• Journal of the Korean Geosynthetics Society
• /
• v.14 no.4
• /
• pp.59-77
• /
• 2015

In order to meet the new requirements for landfill materials, this study planned a study to apply mixed soil of mixing bottom ash and coastal dredged soil to the dredged ground. Coal ash generated from thermal power plant is divided into fly ash and bottom ash. In the case of fly ash, many studies have been conducted because small particles causes permeability coefficient to be small during recycling so no problem has been raised in the environmental area but the utilization of bottom ash has been limited because environmental problems have been raised during recycling due to its larger particle size and greater permeability coefficient. According to recently published studies, however, the results of the study that conducted the water analysis of leachate generated in the ground improvement section using bottom ash showed that heavy metal contamination levels were found to be within the reference value and no significant environmental problems were found so utilization of bottom ash is evaluated to increase significantly in the future. This bottom ash has the particle size of sand and only transportation costs need to be considered when providing materials because the majority has been disposed and it is judged as the most suitable material in dredging landfill in the economic aspect because most thermal power plants are located in the coast and transportation costs can be reduced by ship. Also, research on mixed soil that can maximize the effect of the construction period and construction cost savings than dredged soil is determined as needed because the demand for coastal dredging reclamation is increasing such as Saemangeum project etc. Therefore, we studied self-weight consolidation characteristics depending on sample processing and mixing method of mixed soil by carrying out interior self-weight consolidation experiments on mixed soil of mixing bottom ash and Kaolinite according to the new development needs of recent coastal reclaimed ground and these result findings are expected to be used as basic data when applying the large coastal dredged ground in the future.

• Progress in Medical Physics
• /
• v.17 no.3
• /
• pp.179-186
• /
• 2006

Purpose: Photon beam data of linear accelerators in Korea are collected, analyzed, and a simple method for checking and verifying the dose calculations in a TPS are suggested. Materials and Methods: Photon beam data such as output calibration condition, output factor, wedge factor, percent depth dose, beam profile, and beam quality were collected from 26 institutions in Korea. In order to verify the accuracy of dose calculation, ten sample planning tests were peformed. These Include square, elongated, and blocked fields, wedge fields, off-axis dose calculation, SSD variation. The planned data were compared to that of manual calculations. Results: The average and standard deviation of photon beam quality for 6, 10, and 15 MV were $0.576{\pm}0.005,\;0.632{\pm}0.004,\;and\;0.647{\pm}0.006$, respectively. The output factors of 6 MV photon beam measured at depth of dose maximum for $5{\times}5cm,\;15{\times}15cm,\;20{\times}20cm\;were\;0.944{\pm}0.006,\;1.031{\pm}0.006,\;and\;1.055{\pm}0.007$. For 10 MV photon beam, the values were $0.935{\pm}0.006,\;1.031{\pm}0.007,\;1.054{\pm}0.0005$. The collected data were not enough to calculate average, the output factors for 15MV photon beam with field size of $5{\times}5cm,\;15{\times}15cm,\;20{\times}20cm\;were\;0.941{\pm}0.008,\;1.032{\pm}0.004,\;1.049{\pm}0.014$. There was seven institutions $e{\times}ceeding$ tolerance when monitor unit values calculated from treatment planning system and manually were compared. The measured average MU values for the machines calibrated at SAD setup were 3 MU and 5 MU higher than the machines calibrated at SSD for 6 MV and 10 MV, respectively except the wedge case. When the wedges were inserted, the MU values to deliver 100 cGy to 5 cm depends on manufactures. When the same wedge angle was used, Siemens machine requires more MUs then Varian machine. Conclusion: In this study, photon beam data are collected and analyzed to provide a baseline value for chocking beam data and the accuracy of dose calculation for a treatment planning system.

• Journal of Global Scholars of Marketing Science
• /
• v.17 no.3
• /
• pp.1-19
• /
• 2007

1. Purpose Rural tourism is made by individuals with different characteristics, needs and wants. It is important to have information on the characteristics and preferences of the consumers of the different types of existing rural accommodation. The stud aims to identify the determinants of consumer preference by type of accommodations. 2. Methodology 2.1 Sample Data were collected from 1000 people by telephone survey with three-stage stratified random sampling in seven metropolitan areas in Korea. Respondents were chosen by sampling internal on telephone book published in 2006. We surveyed from four to ten-thirty 0'clock afternoon so as to systematic sampling considering respondents' life cycle. 2.2 Two-step cluster Analysis Our study is accomplished through the use of a two-step cluster method to classify the accommodation in a reduced number of groups, so that each group constitutes a type. This method had been suggested as appropriate in clustering large data sets with mixed attributes. The method is based on a distance measure that enables data with both continuous and categorical attributes to be clustered. This is derived from a probabilistic model in which the distance between two clusters in equivalent to the decrease in log-likelihood function as a result of merging. 2.3 Multinomial Logit Analysis The estimation of a Multionmial Logit model determines the characteristics of tourist who is most likely to opt for each type of accommodation. The Multinomial Logit model constitutes an appropriate framework to explore and explain choice process where the choice set consists of more than two alternatives. Due to its ease and quick estimation of parameters, the Multinomial Logit model has been used for many empirical studies of choice in tourism. 3. Findings The auto-clustering algorithm indicated that a five-cluster solution was the best model, because it minimized the BIC value and the change in them between adjacent numbers of clusters. The accommodation establishments can be classified into five types: Traditional House, Typical Farmhouse, Farmstay house for group Tour, Log Cabin for Family, and Log Cabin for Individuals. Group 1 (Traditional House) includes mainly the large accommodation establishments, i.e. those with ondoll style room providing meals and one shower room on family tourist, of original construction style house. Group 2 (Typical Farmhouse) encompasses accommodation establishments of Ondoll rooms and each bathroom providing meals. It includes, in other words, the tourist accommodations Known as "rural houses." Group 3 (Farmstay House for Group) has accommodation establishments of Ondoll rooms not providing meals and self cooking facilities, large room size over five persons. Group 4 (Log Cabin for Family) includes mainly the popular accommodation establishments, i.e. those with Ondoll style room with on shower room on family tourist, of western styled log house. While the accommodations in this group are not defined as regards type of construction, the group does include all the original Korean style construction, Finally, group 5 (Log Cabin for Individuals)includes those accommodations that are bedroom western styled wooden house with each bathroom. First Multinomial Logit model is estimated including all the explicative variables considered and taking accommodation group 2 as base alternative. The results show that the variables and the estimated values of the parameters for the model giving the probability of each of the five different types of accommodation available in rural tourism village in Korea, according to the socio-economic and trip related characteristics of the individuals. An initial observation of the analysis reveals that none of variables income, the number of journey, distance, and residential style of house is explicative in the choice of rural accommodation. The age and accompany variables are significant for accommodation establishment of group 1. The education and rural residential experience variables are significant for accommodation establishment of groups 4 and 5. The expenditure and marital status variables are significant for accommodation establishment of group 4. The gender and occupation variable are significant for accommodation establishment of group 3. The loyalty variable is significant for accommodation establishment of groups 3 and 4. The study indicates that significant differences exist among the individuals who choose each type of accommodation at a destination. From this investigation is evident that several profiles of tourists can be attracted by a rural destination according to the types of existing accommodations at this destination. Besides, the tourist profiles may be used as the basis for investment policy and promotion for each type of accommodation, making use in each case of the variables that indicate a greater likelihood of influencing the tourist choice of accommodation.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.4
• /
• pp.65-70
• /
• 2005

Many case histories of re-liquefaction phenomena seem to support the idea that sand deposits, if they once have been liquefied, could be reliquefied again by a subsequent earthquake even though the earthquake is smaller than the previous one. The magnitude of the strains induced in the initial liquefaction has a significant influence on the resistance of the sample to re-liquefaction. The deposits undergoing liquefaction experience large shear strain during liquefaction. And this previous strain changes the microstructure into highly anisotropic structure such as columnlike structure and connected voids. This type of anisotropy is so unstable that it can reduce re-liquefaction resistance. It is blown that the extent of anisotropic structural change depends on the gradation characteristics of ground. The purpose of this study is to estimate the correlation between the gradation characteristics of the sand and the ratio of re-liquefaction resistance to liquefaction resistance. In this study, 1-g shaking table tests were carried out on five different kinds of sands. During the tests the values of excess pore pressure at various depths and surface settlements were measured. Re-liquefaction resistances were not affected by the initial void ratio and the effective confining pressures, and the deposits of all test sands which had once been liquefied were reliquefied in the cyclic loading number below 1 to 1.5. The ratio of re-liquefaction resistance to liquefaction resistance linearly decreased as $D_{10}/C_u$ increased, and was constant as about 0.2 above the value of $D_{10}/C_u$, 0.15 mm.

• Analytical Science and Technology
• /
• v.25 no.6
• /
• pp.483-491
• /
• 2012

This study is to investigate the issues on how to secure stability during the purification process for the production of recombinant protein A. The final recombinant protein A is produced by passing through the cation exchange column (SP) and the anion-exchange column (Q) during the production process, for which the samples produced by the step-by-step processes can be exposed to trouble in securing stable storage in case the next process cannot be taken within the proper time period. Accordingly, this study aims to evaluate the proper storage conditions and length of time when storing samples produced in the production process. That is, in this study, how to store fair samples, how long the storage period should be set up, and how to evaluate the security of its quality depending on time are dealt with. The items to be experimented with were enodotoxin, SDS-PAGE, HPLC purity and concentration. Experimental results showed that after passing the cation exchange column, when stored at $4^{\circ}C$ or room temperature, SDS-PAGE showed a major band, endotoxin is 5.0 Eu/mg or less, and concentration is on average of 8.21 to 8.24 mg/mL and RSD% 0.10~0.62%. In addition, HLPC purity showed somewhat stable results; at the HPLC purity 214 nm, the average is 99.24% to 99.37% and RSD% is 0.22~0.29%, while the average is 89.72% to 89.80% and RSD% 0.62~1.26% at 280 nm. On the contrary, after passing the anion exchange column, when stored at $4^{\circ}C$ or room temperature, SDS-PAGE revealed the major band, endotoxin is 0.5 Eu/mg or less, and concentration is on average of 5.59 mg/mL and RSD% 0.03~0.10%. when it comes to HLPC purity, the result showed that at the HPLC purity 214 nm, the average is 99.74% and RSD% is 0.10~0.11%, while the average is 96.16% to 96.85% and RSD% 0.72~1.13%. In conclusion, the stability of fair samples of recombinant protein A during the manufacturing process could be obtained without substance decomposition for 7~8 days at $4^{\circ}C$ or 20~21 days at room temperature.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.16 no.4
• /
• pp.314-323
• /
• 2006

This study was conducted to identify ingredients of thinners and to confirm reliability of material safety data sheets (MSDS) of thinners for public and workers' health. The 41 thinner products were collected from paint shops located in Busan and Gyeongnam province. The 12 thinner products among them were identified using product MSDS. GC-MSD was used to analyze 41 kinds of thinners qualitatively and quantitatively. The 12 products MSDS were compared with thinner's component through qualitative analysis to confirm MSDS. Chemical ingredients, such as Benzene, Toluene, and Xylene etc., of thinners were analysed in quantity. The 41 thinner products contained 17 disclosed specific, trade name, or generically described chemical solvent ingredients. These 17 ingredients came under 6 classes: alcohols, aromatic hydrocarbons, esters, glycol ethers, ketones, and mixtures. These 17 ingredients were important in the view of industrial hygiene and had occupational exposure limit in the ambient, such as toluene, xylene, acetone, nonane, EGEE, heptane, cumene, MIBK, indene, tri-methyl benzene, etc, were found in 41 kinds of thinners. Aromatic hydrocarbons were the most identified ingredient in thinners. Especially, the benzene, which induces leukemia, was found in 4 kinds of thinners. The content rates of benzene in thinners were 0.25~1.18%. The benzene in enamel thinner, which were 0.39~0.72%, was highest from chemical classification. The contents of toluene, which was found from 27 kinds of thinners, were 5.35~64.16%, which were highest in sobu thinner as 58.80%. Xylene was found from 22 kinds of thinners and contents of xylene were 4.61~72.42%. Acrylic thinner's contents of xylene were 12.06~51.05%, which was most high. It was found that contents of benzene were increased and frequency of detection was decreased through comparison with other study. The MSDS possession rate of paint shops was low as 29.27%. So it did not provide information with public or workers. Mean of agreement rate between MSDS and components of thinners through qualitative analysis was 42.01% and it has wide range from 8.3% to 75%. There are many deficiencies in MSDS about component of thinners. In some case of sample, expecially, despite containing benzene, information was not written it on MSDS.

• Journal of the Korean Society of School Health
• /
• v.14 no.1
• /
• pp.131-143
• /
• 2001

The primary aim of this dissertation is to contribute to the improvement of methods in physical examination by providing quality information for the current school system and advice for improving status. Present status, controversial points and possible remedies in physical examination were analyzed on a frequency and percentage basis. An $x^2$-test was used to verify the statistics between the results from the examination and each variable. In case of multiple categories of variables, an $x^2$ cs was adopted. Chronological data as well as both total and sampling physical examination data verified the statistics using an $x^2$-test. This thesis is based both on the data from middle school health care specialists in Gyunggi Province and on the analysis of physical examinations reported from local schools to the municipal education agency from 1997 to 1999. The results of the study are as follows: First, according to the survey, only 29.0% of the total schools had their school doctors examine all the students while most of the educational institutions failed to implement the whole process of physical examination on the list. It also turned out that the more students the schools have, the lower the rate of implementation of physical examination by school doctors(p=0.014). Second, the average time a school doctor spends for checkup turned out to be approximately 1.7 minutes per student This means that the quality of the physical examination is not guaranteed in the process. Third, 47.7% of those surveryed say that a dental examination was performed, each taking 21.24 seconds on average. In addition, it shows that some 31.5% wanted to have a task force team for dental checkups at the local health center. Given the fact that dental caries among students is progressively on the rise, the dental health centers that are now set up in some elementary schools should be expanded to cover the whole educational institution in order to raise awareness of the importance of dental care. Fourth, 48.5% of those surveyed say that a comprehensive physical examination should be adopted to promote the health of high schoolers. Since it takes a lot of public funds to implement a comprehensive method, it is essential to make sure that in-depth studies should be based on the frequency and methods of physical examination. Fifth, regarding such diseases among 3rd year middle school students in 1999, statistics shows that there was a slight difference in the prevalence rate of color blindness, and allergic diseases for male students ; and color blindness, hearing disturbance and allergic disease for female students. For those items, however, it is too little to say that there is a significant difference and accordingly it is assumed to be a problem of the measuring process. Sixth, the result of analysis on the sample physical examination and the total physical examination of the year 1999 shows as follows: For male students in the 3rd year of middle school, a slight difference appeared to those students in 11 items including eye problems and eye disease, otitis media, tonsillar hypertrophy, spinal shape, respiratory urinary allergic disease and other abnormal diseases(p<0.05). Particularly, the prevalence rate between students with and without disease was shown to be two times more in the following: eye problems, otitis media, tonsill hypertrophy, allergic diseases, etc. For female students in the 3rd year, prevalence rate showed little difference in 14 items(p<0.05). For items including eye problem, otitis media, tonsill hypertrophy, allergic disease, etc. it was shown that the rate was two times more between students with and without diseases. Physical examinations under the current school system are not producing any fundamental results for the health of the students. Methods and results are not trustworthy. Accordingly, a drastic overhaul of the current practices is needed in frequency, methods and items on the list in order to promote the health of the students. Cost-benefit studies as well as political considerations to ensure the development of efficient methods for physical examination are urgently needed at this moment.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.10-24
• /
• 1979

It is understood that drum speed of threshers and the moisture content of paddy grains to be threshed, respectively, have a signific:mt effect upon rice recoveries. Threshing under an increased drum speed would give a high performance rate, which is the general practice in custom work threshing in association with the use of semiauto-t hreshers. In the connection, however, it may result in the promotion of grain cracks and brokens of the rice product after milling. No reference or determination for an opti mum drum speed of the thresher is made available for various grain moisture contents at the time of the threshing operation and for different rice varieties especially for the Tongil rice varieties. This study was Conducted to find out and determine effects of the drum speeds on grain losses. The grain loss was quantified in terms of recovery rates of rice grains after treatments. Samples of each of all treatments were taken from the grain sampling plate placed in the grain conveyor of threshers. The grain sample plate was specially provided for this experiment. The brown-rice, milling, and head-rice recJveries were tes ted in the laboratory mill, respectively. Two rice varieties, Akibare and Suweon 251, each with five levels of different moist\ulcornerure contents at harvest and six levels of different drum speeds of threshers, were selected and used for treatments in this experiment. Two conditions of materials were tested in the thresher. One condition was to thresh the experimental material immediately after cutting, referred to as the wet-material thr eshing in this study. The other was to thresh the experimental :material, dried to contain about 15-16 percent of the grain moisture under the shocking operation. This is referred to as the dry-material threshing in this study. In additioon, field measurements for the grain moistures and drum-sdeeds under actual operation practices of the traditional field threshing, were conducted with a view to comparing with results of the experimental treatments. The results of the study may be summarized as follows: 1. For threshing treatments of Japonica-type rice variety (Akibare) , the effect of drum speeds and levels of grain moisture at cutting upon brown-rice, milling, and head-rice recoveries were found statistically significant. No significant difference in these recovery rates was noticed regardless of whether the material was threshed right after cutting or after drying by the shocking operation. 2. For the Tongil-sister rice variety(Suweon 251), milling recovery for the varied drum-speed and the grain~moisture level at cutting was found statististically significant. Th milling recovery was much significant when associated with the wet-material thres\ulcornerhing compared to the dry-material threshing. 3. The optimum peripheral velocity to be maintained at the edge of teeth on the thr\ulcorneresher drum was determined and may be recommanded as that of about 12 to 13 meters per second in view of the maximum recovery rate of the milled rice. 4. The effect of the drum speed on the qualitative loss of the milled rice was much greater in the case of the Tongil variety than Japonica. This effect was also greater by the wet-material threshing than by the dry-material threshing. Therefore, to apply the wet-material threshing operation for the Tongil variety, in particular, it should be very important to introduce the kind of threshing technology which would maintain the drum speed at optimum. 5. A field survey for the actual drum speed of threshing operations for 50 threshers indicated that average peripheral velccity was 12.76m/sec., and that the range was from 10.50 to 14.90m/sec. Approximately, more than 30% of the experimented and measured threshers were being operated at speeds which exceeded the optimum speed determined and assessed in this study. Accordingly, it should be highly desirable and important to take counter-measures against these threshing practices of operational overspeed.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.9-9
• /
• 1979

It is understood that drum speed of threshers and the moisture content of paddy grains to be threshed, respectively, have a signific:mt effect upon rice recoveries. Threshing under an increased drum speed would give a high performance rate, which is the general practice in custom work threshing in association with the use of semiauto-t hreshers. In the connection, however, it may result in the promotion of grain cracks and brokens of the rice product after milling. No reference or determination for an opti mum drum speed of the thresher is made available for various grain moisture contents at the time of the threshing operation and for different rice varieties especially for the Tongil rice varieties. This study was Conducted to find out and determine effects of the drum speeds on grain losses. The grain loss was quantified in terms of recovery rates of rice grains after treatments. Samples of each of all treatments were taken from the grain sampling plate placed in the grain conveyor of threshers. The grain sample plate was specially provided for this experiment. The brown-rice, milling, and head-rice recJveries were tes ted in the laboratory mill, respectively. Two rice varieties, Akibare and Suweon 251, each with five levels of different moist?ure contents at harvest and six levels of different drum speeds of threshers, were selected and used for treatments in this experiment. Two conditions of materials were tested in the thresher. One condition was to thresh the experimental material immediately after cutting, referred to as the wet-material thr eshing in this study. The other was to thresh the experimental :material, dried to contain about 15-16 percent of the grain moisture under the shocking operation. This is referred to as the dry-material threshing in this study. In additioon, field measurements for the grain moistures and drum-sdeeds under actual operation practices of the traditional field threshing, were conducted with a view to comparing with results of the experimental treatments. The results of the study may be summarized as follows: 1. For threshing treatments of Japonica-type rice variety (Akibare) , the effect of drum speeds and levels of grain moisture at cutting upon brown-rice, milling, and head-rice recoveries were found statistically significant. No significant difference in these recovery rates was noticed regardless of whether the material was threshed right after cutting or after drying by the shocking operation. 2. For the Tongil-sister rice variety(Suweon 251), milling recovery for the varied drum-speed and the grain~moisture level at cutting was found statististically significant. Th milling recovery was much significant when associated with the wet-material thres?hing compared to the dry-material threshing. 3. The optimum peripheral velocity to be maintained at the edge of teeth on the thr?esher drum was determined and may be recommanded as that of about 12 to 13 meters per second in view of the maximum recovery rate of the milled rice. 4. The effect of the drum speed on the qualitative loss of the milled rice was much greater in the case of the Tongil variety than Japonica. This effect was also greater by the wet-material threshing than by the dry-material threshing. Therefore, to apply the wet-material threshing operation for the Tongil variety, in particular, it should be very important to introduce the kind of threshing technology which would maintain the drum speed at optimum. 5. A field survey for the actual drum speed of threshing operations for 50 threshers indicated that average peripheral velccity was 12.76m/sec., and that the range was from 10.50 to 14.90m/sec. Approximately, more than 30% of the experimented and measured threshers were being operated at speeds which exceeded the optimum speed determined and assessed in this study. Accordingly, it should be highly desirable and important to take counter-measures against these threshing practices of operational overspeed.

• Journal of KIISE:Software and Applications
• /
• v.30 no.1_2
• /
• pp.117-128
• /
• 2003

Software usability is a characteristic of the software that is decided based on learnability, effectiveness, and satisfaction when it is evaluated. The usability is a main factor of the software quality. A software has to be continuously improved by taking guidelines that comes from the usability evaluation. Usability factors may vary among the different software products and even for the same factor, the users may have different opinions according to their experience and knowledge. Therefore, a usability evaluation process must be developed with the consideration of many factors like various applications and users. Existing systems such as satisfaction evaluation and performance evaluation only evaluate the result and do not perform cause analysis. And also unified evaluation items and contents do not reflect the characteristics of the products. To address these problems, this paper presents a evaluation model that is based on the mental model of user and the problems, this paper presents a evaluation model that is based on the mental model of user and the emotion of users. This model uses evaluation factors of the user task which are extracted by analyzing usage of the target product. In the mental model approach, the conceptual model of designer and the mental model of the user are compared and the differences are taken as a gap also reported as a part to be improved in the future. In the emotional factor approach, the emotional factors are extracted for the target products and evaluated in terms of the emotional factors. With this proposed method, we can evaluate the software products with customized attributes of the products and deduce the guidelines for the future improvements. We also takes the GUI framework as a sample case and extracts the directions for improvement. As this model analyzes tasks of users and uses evaluation factors for each task, it is capable of not only reflecting the characteristics of the product, but exactly identifying the items that should be modified and improved.