• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.48 no.2
• /
• pp.147-154
• /
• 2012

In head sea, a ship has mainly the longitudinal motion such as vertical acceleration and pitch. In that case, the motion characteristics of a ship will have changed as the location different from each of place vertically and horizontally on board. The author carried out an experiment about the ship's vertical acceleration and pitch according to the location for the head sea, and analyzed the data with the aid of the statistical and spectral analyzing method to get the motion characteristics of the vessels. The response of vertical acceleration and pitch not deeply depend on the decks vertically, but displayed the relative big different value horizontally even if same deck. The biggest response of vertical acceleration and pitch among the accommodations was shown at scientist room, but the value of it not reached to the minimum requirement of ISO 2631-1 for working on board.

• Journal of Biosystems Engineering
• /
• v.31 no.3 s.116
• /
• pp.139-145
• /
• 2006

A previous study showed that the handle vibration of a walking type cultivator can be reduced by adding a mass to the handle. This study was conducted to determine the optimum magnitude and location of the mass to be added for the same cultivator. The possible locations of added mass were determined by investigating nodal points of the handle vibration by an ODS (operational deflection shapes) test at an engine frequency of 52 Hz. The optimum location was then determined as one that moved the nodal points to the hand grip of the handle bar. To determine the optimum magnitude of the mass, the possible locations were added by a mass from 0.2 to 2.0 kg in an increment of 0.2 kg. The optimum magnitude was then determined as a mass which minimized the vibration level at the hand grip. For the case of this study, the z-axis vibration at the hand grip was reduced from $2.67m/s^2\;to\;0.88m/s^2$ resulting in a reduction of 67% and the total vibration from $4.09m/s^2\;to\;3.27m/s^2$ resulting in a 20% reduction by adding an optimum mass to the optimum location.

• Aerospace Engineering and Technology
• /
• v.3 no.1
• /
• pp.267-271
• /
• 2004

The satellite in the geostationary orbit rotates around Earth center with the same angular rate as the Earth. So, the Earth can be observed with sequential time series. GOES(Geostationary Operational Environmental Satellites)-9 is a meteorological satellite, which is now located at 155ㆁE geostationary orbit location in order to monitor East-Asia meteorological environment including Korean Peninsular. Every meteorological information is acquired from GOES-9 with the period of about 1 hour. COMS(Communication, Ocean and Meteorological Satellite) has been developed by KARI(Korea Aerospace Research Institute) since 2003 and will be launched at 2008. COMS will be located at different orbit location compared to GOES-9. In this study, a simulated COMS image which is the perspective from different geostationary orbit location is generated using an GOES-9 image.

• Journal of architectural history
• /
• v.8 no.1 s.18
• /
• pp.41-52
• /
• 1999

This study aims to infer the plan and location of the government office building in Chongju Castle in the Late Yi-dynasty. The conclusion is as follows: 1. The Chongju Castle Map(淸州邑城圖, late in the 18th century, hereinafter referred to CCM) provides the detail arrangement and location of Government Office Building in Chongju Castle. And the road structure and plan of the CCM is almost same with the present time. 2. As compared with CCM and a Chongju-land Registration Map(淸州面地籍原圖, 1913, CRM) to infer the location of the traditional government office building in Chongju Castle, the building locations of Gaek-Sa(客舍) Donghun(東軒)'s region in CCM are almost accordance with today's. But those of Byungyoung(兵營) Group's region are represented by a little error. So the locations of Byungyoung(兵營) Group's region rearranged, moved down to be in accordance with the approach circulation of Main Gate(閉門樓) which is shown in CRM. 3. The records, on the plan of the traditional government office building in Chongju Castle, have proved that the plan of Gaek-Sa was a width of 11 bay and a depth of 2 bay. A width of 3 bay drawn in CCM, the present plan of Donghun is a width of 7 bay and a depth of 4 bay. The main building and especially the double-storied Main Gate($4{\times}3$) of Byungyoung Group are exactly in keeping with the present road structure.

• Journal of Industrial Technology
• /
• v.14
• /
• pp.127-140
• /
• 1994

This study is concerned with the accuracy and the patterns when different methods was used in interpolation task. Although 3 methods employed the same modality for input (visual) and for output (manual responding), they differed in central processing, which method 1 is relatively more tendency of verbal processing, method 2 is realtively more tendency of spatial processing and method 3 needed a number of switching code (verbal/spatial) performing task. Split-plot design was adopted, which whole plot consisted of methods (3), orientations (horizon, vertical), base-line sizes (300, 500, 700 pixels) and split plot consisted of target locations (1-99). The results showed the anchor effect and the range effect. Method 2, method 3 and method 1 that order was better accuracy. ANOVA showed that the accuracy was significantly influenced by the method, the location of target, and its interactions ($method{\times}location$, $size{\times}location$). Analysis of error data, response time and frequency of under, just, over estimate indicated that a systematic error pattern was made in task and methods changed not only the performance but also the pattern. The results provided support for the importance of the multiple resources theory in accounting for S-C-R compatibility and task performance. They are discussed in terms of multiple resources theory and guidelines for system design is suggested by the S-C-R compatibility.

• Structural Engineering and Mechanics
• /
• v.26 no.3
• /
• pp.315-341
• /
• 2007

A sudden change of stiffness in a structure, associated with the events such as weld fracture and brace breakage, will cause a discontinuity in acceleration response time histories recorded in the vicinity of damage location at damage time instant. A new damage index is proposed and implemented in this paper to detect the damage time instant, location, and severity of a structure due to a sudden change of structural stiffness. The proposed damage index is suitable for online structural health monitoring applications. It can also be used in conjunction with the empirical mode decomposition (EMD) for damage detection without using the intermittency check. Numerical simulation using a five-story shear building under different types of excitation is executed to assess the effectiveness and reliability of the proposed damage index and damage detection approach for the building at different damage levels. The sensitivity of the damage index to the intensity and frequency range of measurement noise is also examined. The results from this study demonstrate that the damage index and damage detection approach proposed can accurately identify the damage time instant and location in the building due to a sudden loss of stiffness if measurement noise is below a certain level. The relation between the damage severity and the proposed damage index is linear. The wavelet-transform (WT) and the EMD with intermittency check are also applied to the same building for the comparison of detection efficiency between the proposed approach, the WT and the EMD.

• Journal of the Korean Institute of Rural Architecture
• /
• v.10 no.1
• /
• pp.27-35
• /
• 2008

After researching 40 rural areas named 'valley' in Goesan County, Chungbuk Province, they are classified by 2 two classes. Firstly, villages located on the crossways valley are 22 of 40, they are located on the valley which is at right angles with a direction of light of a mountain range. A closed valley location is placed in the deep valley against a background mountain range. It is divided with closed large valley and small valley. Secondly, an open valley location style is 14 of 40. It means the villages are paralleled with a direction of mountain and located with same direction of entrance. This study is carried out to understand the characteristic of location in vernacular agricultural villages by judging from natural environment around the village. For this purpose, there were selected 3 villages of the valley categirized villages in Geosan Area which lean against valley. After classifying these sample by the morphorogical approach, according to compare them with pre-researched villages, the methodology of spatial structure was investigated in agriculture villages.

• Journal of Welding and Joining
• /
• v.23 no.6
• /
• pp.87-92
• /
• 2005

It has been well hewn that ductile fracture of steels is accelerated by triaxial stresses. The characteristics of ductile crack initiation in steels are evaluated quantitatively using a two-parameters criterion based on equivalent plastic strain and stress triaxiality. The present study focuses on the effects of strength mismatch, which can elevate plastic constraint due to heterogeneous plastic straining, on the critical condition for ductile fracture initiation usinga two-parameter criterion. Fracture initiation testing has been conducted under static loading using notched round bar specimens which had different notch locations. This study provides the fundamental clarification of the effect of strength mismatching and effect of notch location on the critical condition to ductile crack initiation from notch root using fuite element method and ultrasonic-mechatronics system. The critical condition of ductile crack initiation from notch root of strength mismatched tensile specimens under static loading appeared to be almost the same as those of homogeneous tensile specimens with circumferential sharp notch specimen. Also, the effect of notch location in mismatched specimens was estimated using finite element(FE) analyses.

• Nuclear Engineering and Technology
• /
• v.51 no.6
• /
• pp.1681-1688
• /
• 2019

In accordance with ASME Boiler and Pressure Vessel (B&PV) Code Sec.XI Appendix. G, a postulated crack is located at the beltline of a reactor pressure vessel because the neutron flux at the beltline is higher than elsewhere. This means that the distance between the core and the semi-spherical bottom head is longer than the distance between the core and the cylindrical beltline. However, several Small and Medium sized Reactors have bottom heads with diverse shapes, including dished or semi-elliptical shapes, to satisfy the requirement and performance. So, the aim of this paper is to evaluate the effect of crack location on Pressure-Temperature limit curve. To do this, two types of postulated crack location, such as beltline and semi-elliptical bottom head, were adopted to derive the Pressure-Temperature limit curve. Also, parametric studies for neutron flux, crack shape and so on were performed. As a result, core critical temperature of semi-elliptical bottom head is found to higher than that of beltline even when they have same values of thickness and neutron flux. This result will be useful to enhance the understanding of Pressure-Temperature limit curve.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.4
• /
• pp.29-35
• /
• 2014

The formula contains up between the text and the structural information, as well as their mathematical symbols. Research on-line or off-line recognition formula is underway actively used in various fields, and various forms of the equation are implemented recognition system. Although many documents are included in the various formulas, it is not easy to enter a formula into the computer. Recognition of the expression is divided into two processes of symbol recognition and structural analysis. After analyzing the location information of each character is specified to recognize the effective area after each symbol, and to the structure analysis based on the proximity between the characters is recognized as an independent single formula. Furthermore, analyzing the relationship between the front and back each time a combination of the position relationship between each symbol, and then to add the symbol which was able to easily update the structure of the entire formula. In this paper, by using a scanner to scan the book formula was used to interpret the meaning of the recognized symbol has a relative size and location information of the expression symbol. An algorithm to remove the formulas for calculation of the number of formula is present at the same time is proposed. Using the proposed algorithms to scan the books in the formula in order to evaluate the performance verification as 100% separation and showed the recognition rate equation.