• Korean Journal of Optics and Photonics
• /
• v.4 no.3
• /
• pp.354-358
• /
• 1993

The temperature distribution inside a zigzag slab laser glass was measured using a Mach-Zehnder interferometer. The temperature difference between the center and the surface of the slab caused the fracture of the slab glass. Two laser glasses were fractured at a temperature difference ${\Delta}T_0$of TEX>$110^{\circ}C$, $62^{\circ}C$ respectively. For the design of high-average power glass laser, it is recommended that the limit of the temperature difference ${\Delta}T_0$ inside the slab glass should be smaller than $50^{\circ}C$ for safe operation.ration.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.90-99
• /
• 2002

The main purpose of this study lies on the development of micro dilution tunnel based on the Sierra Dilution chamber model. As a primary examination, characteristics of flow and temperature distributions during the steady dilution process in dilution chamber are observed with numerical analysis. The penetration of dilution air through porous tube as well as wall temperature and temperature gradient inside porous tube are examined. The thermophoretic velocity in terms of temperature behavior inside porous tube are defined and examined. Based on the ratio of penetration and thermophoretic velocities, all part of porous tube are shown to be safe from the particulate depositions. However, The inlet portion of porous tube in addition to the portion of impinging of dilution air are marginally safe from the particulate depositions. Generally the safer design against particulate deposition is required in provision f3r steady dilution process and for transient process as well.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1543-1546
• /
• 1994

Ignitabilility of explosive gas mixture by spark of dry cell in case of short circuit by accident was studied for the purpose of evaluation of intrinsically safe characteristics of dry cell that manufactured in Korea. IEC type spark test apparatus, $21{\pm}2$ Vol% of hydrogen - air mixture, and dry cell that produced in Korea was used for the experiment. The result of this research could be used for design, manufacturing, and using the intrinsically safe electrical apparatus.

• Proceedings of the Safety Management and Science Conference
• /
• 2008.04a
• /
• pp.47-51
• /
• 2008

Recently, the development of technology has been rapidly proceeding with information technology in various fields. Due to their abstract properties, proper evaluation of intangible assets is very difficult compared to evaluation of tangible assets. Intangible assets are knowledge, technology, and design etc. In general there are two approaches to evaluate the intangible assets such as qualitative and quantitative approach. The qualitative approach contains scoring approach, profile approach, checklist approach, and quantitative approach. Quantitative approach contains cost approach, market approach, income approach, and real-option approach. As an initial step for evaluation of safe work environments, this study compares and analyzes evaluation methods of intangible assets.

• Journal of the Korean Society of Safety
• /
• v.8 no.4
• /
• pp.133-138
• /
• 1993

The stable and safe operation of a boiler system is essential for ensuring stability of the chemical processes. A dynamic simulation of a boiler drum was performed to identify the dynamics of the boiler drum. The obtained results represented that the variation of process variables disturb boiler system. So, disturbance rejection with tracking and constraints handing was necessary for stable operation of boiler drum. Among many controller, GPC has been known to show good performance in set point tracking than disturbance. In order to improve disturbance rejection performance measurable disturbance term was Introduced in basic GPC model. The controller which had tracking and disturbance rejection was designed for Improving the stable operation of a boiler system.

• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.4
• /
• pp.389-395
• /
• 2022

In order to ensure reliability the high-level automated driving such as Advanced Driver Assistance System (ADAS) and universal robot taxi provided by autonomous driving systems, the operation with high integrity must be generated within the defined Operation Design Domain (ODD). For this, the position and posture accuracy requirements of autonomous driving systems based on the safety driving requirements for autonomous vehicles and domestic road geometry standard are necessarily demanded. This paper presents localization requirements for safe road driving of autonomous ground vehicles based on the requirements of the positioning system installed on autonomous vehicle systems, the domestic road geometry standard and the dimensions of the vehicle to be designed. Based on this, 4 Protection Levels (PLs) such as longitudinal, lateral, vertical PLs, and attitude PL are calculated. The calculated results reveal that the PLs are more strict to urban roads than highways. The defined requirements can be used as a basis for guaranteeing the minimum reliability of the designed autonomous driving system on roads.

• International Journal of Highway Engineering
• /
• v.18 no.6
• /
• pp.161-171
• /
• 2016

OBJECTIVES : Many roadway departure crashes on the freeway interchange are due to the running speed being greater than the design speed. This study aims to ensure a safe and pleasant driving experience for the driver by increasing the superelevation based on the running speed on the highway interchange ramp. METHODS : The mean running speed for each type of ramp is calculated on site survey more than 10 interchanges. Using the mean running speed, we calculated the superelevation and the side friction using the method given in "A Policy on Geometric Design of Highways and Street" (Pages 145-166, 2001). Then, we applied the modified method to the superelevation range. Finally, we ensured safety using the Degree of Safety that is proven by the centrifugal acceleration ratio as suggested by Joseph Craus (1978). RESULTS : The mean running speeds are 50 km/h and 65 km/h when the design speeds are 40 km/h and 50 km/h, respectively. After the application of the new method used in this study, the superelevation will be increased by 9.0% and 10.0% when the mean running speeds are 50 km/h and 65 km/h, respectively. CONCLUSIONS : A higher superelevation can give the driver a more comfortable and safe driving environment. However, the driver needs to be aware of snow and low-temperature conditions.

• International Journal of Highway Engineering
• /
• v.14 no.5
• /
• pp.101-111
• /
• 2012

PURPOSES: Because expressway ramps are very complex segments where diverse roadway design elements dynamically change within relatively short length, drivers on ramps are required to drive their cars carefully for safety. Especially, ramps on expressways are designed to guarantee driving at high speed so that the risk and severity of traffic accidents on expressway ramps may be higher and more deadly than other facilities on expressways. Safe deceleration maneuvers are required on off-ramps, whereas safe acceleration maneuvers are necessary on onramps. This difference in required maneuvers may contribute to dissimilar patterns and severity of traffic accidents by ramp types. Therefore, this study was aimed at developing prediction models of the severity of traffic accidents on expressway on- and off-ramps separately in order to consider dissimilar patterns and severity of traffic accidents according to types of ramps. METHODS: Four-year-long traffic accident data between 2007 and 2010 were utilized to distinguish contributing design elements in conjunction with AADT and ramp length. The prediction models were built using the negative binomial regression model consisting of the severity of traffic accident as a dependent variable and contributing design elements as in independent variables. RESULTS: The developed regression models were evaluated using the traffic accident data of the ramps which was not used in building the models by comparing actual and estimated severity of traffic accidents. Conclusively, the average prediction error rates of on-ramps and offramps were 30.5% and 30.8% respectively. CONCLUSIONS: The prediction models for the severity of traffic accidents on expressway on- and off-ramps will be useful in enhancing the safety on expressway ramps as well as developing design guidelines for expressway ramps.

• Journal of Biosystems Engineering
• /
• v.32 no.6
• /
• pp.416-421
• /
• 2007

Physical damage to fruits and vegetables caused by shock degrades the value of product in the fresh market. In order to design a product/packaging system to protect the product, the G-factor to the product that causes shock damage needs to be determined. The shock fragility of organisms such as fruits with a concept correspondent to the G-factor of industrial products was calculated and we defined the allowable bio-shock fragility index as the value divided peak acceleration that was generated in safe drop height by standard acceleration of gravity. We did modeling for safe drop hight that would prevent fruits from damage by drop tests and tried to estimate the allowable bio-shock fragility index of pears and apples for optimum packaging design. The bio-shock fragility index of pears was in the range of $0.74{\sim}2.29\;G$, while apples had a slightly higher value than that of pears, of $0.51{\sim}2.98\;G$. This result shows accordance with the general fact that apples have a firmer structure and get less damage from the same impact. Based on this result, it is possible to create an optimum packaging design by providing a damage standard by impact.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1181-1187
• /
• 2012

For the fatigue design of aircraft landing gear, the safe-life approach is applied. Structural defects such as cracks or detrimental deformations should not occur under the fatigue load spectrum depicting the entire lifetime usage of the aircraft. In the design phase, the fatigue life of the landing gear is estimated analytically by adopting the stress-based approach because the fatigue of aircraft landing gear is generally high-cycle fatigue. This utilizes S-N curves that are factored to produce design curves that account for the scatter and surface finish of the material. In the test and evaluation phases, a fatigue test should be conducted for full-scale landing gear to substantiate the fatigue design requirement in the end. In this study, the procedure for the fatigue test and evaluation of aircraft landing gear is presented with real application cases.