• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.3
• /
• pp.88-94
• /
• 2006

In order to substitute current aluminum sabot and to increase the penetration performance of the kinetic energy projectiles, the research and development program for composites sabot has been conducted. For carbon/epoxy composites sabot, unidirectional carbon fiber reinforced epoxy prepreg was chosen and thick sectioned composites preforms with the different fiber angles along the circumferential direction of sabot were prepared by compression molding under the careful processing conditions at $150^{\circ}C$ for 1hour with $70kgf/cm^2$ curing pressure. The composites sabot demonstrated a weight reduction by approximately 30% than that of current aluminum sabot. The muzzle velocity of a kinetic energy projectile with composites sabot was measured to be about 63m/s higher than that with aluminum sabot. These results imply that the penetration performance is expected to be considerably increased when the composite sabot is applied to the kinetic energy projectiles.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.2
• /
• pp.65-72
• /
• 2003

Composite sabot can increase the penetration performance of APFSDS projectile by reduction of the sabot weight. However, it has a thick-sectioned lamination and the lamination structure is different from those of the conventional composite parts. In this study, modeling technique for a thick and radially-laminated composite part has been applied in the finite element analysis of composite sabot. Four models of composite lamination for the sabot have been proposed and evaluated for their structural strength.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.1
• /
• pp.1-9
• /
• 2018

In this paper, we have proposed a prediction method for sabot-trajectory of projectile using high speed camera data analysis. Through analyzing trajectory of sabot with high speed camera data, we can extract its real velocity and acceleration including effects of friction force, pressure of flume, etc. Using these data, we suggest a prediction method for sabot-trajectory of projectile having variable acceleration, especially for minimum and maximum acceleration, by using interpolation method for velocity and acceleration data of sabot. Also we perform the projectile launching tests to achieve the trajectory of sabot in case of minimum and maximum thrust. Simulation results show that they are similar to real tests data, for example velocity, acceleration and the trajectory of sabot.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.4
• /
• pp.63-72
• /
• 2003

This paper deals with the analysis of composite sabot of APFSDS projectile. Unlike conventional composite parts, the sabot is composed of thick-sectioned lamination, and thus requires 3-dimensional properties in the analysis. In this study, a model was formulated to calculate the equivalent composites properties. The equivalent properties were then used in the finite element analysis and the results were compared with those by the full 3-dimensional analysis with ply-by-ply modeling. The results generally agreed with each other in the bound of 20% error, indicating that the formulated model produced the equivalent properties with reasonable accuracy. It was thought to be an efficient approach to use the model in global analysis and then perform the full 3-dimensional analysis in regions of interest for detailed evaluation in designing the composite sabot structure.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.269-274
• /
• 2001

This research covers the development of new technique for composite injection molding of high stiffness Sabot. An analysis of polymer resin is performed by means of making test specimen mold and doing test with accordance of ASTM test guidelines. Structural analysis and simulation of injection molding process are carried out in order not only to estimate but also to predict the characteristics of molding stresses what both product and structure of mold may have. For structural analysis software, Moldflow and LS-dyna are used and universal test machine is utilized for evaluating performance of sabot. Cases of adopting this material to sabot are not announced yet in domestic academic world. In addition to that, materials for polymer-metal mixed injection molding are imported on the whole due to deficient level of domestic technology. Therefore, this new developed injection molding technique using PEI material can make it available to ensure the technology of making mold, injection and design. Finally, this technique may be applicable to another sabot having different radius of warheads from now on.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.5
• /
• pp.572-582
• /
• 2018

In this paper, we have calculated a formular for sabot-trajectory of shipboard projectile including ship motion and generated trajectory-range function for analysing interference with structure of naval ship. We make formula to approximate the ship motion data of naval ship using optimization technique. Through this formula, we calculate the velocities and accelerations of sabot caused by ship motion(surge, sway, heave, roll, pitch, yaw) and then, we produce the formula about the trajectory of sabot including effects of ship motion in addition to previous study which had considered the effects of the pressure of flume, friction force, etc. To investigate interference with ship structures, we make the trajectory-range functions and then extract the nearest or farthest trajectory to ship structure. Through these data, we can conform whether the interference is happened or not.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.1
• /
• pp.37-42
• /
• 2020

This study is for a bulletproof experiment through speed acceleration of steel ball(2.385 mm) at the laboratory level. The secondary propulsion method is used for speed acceleration, which uses a sabot assembly consisting of a sabot body, a plunger, water, and a sabot cap. At the core of the secondary drive, it is important that the energy in the water of the private particle is transferred well to the steel ball. The experiment was conducted by selecting a plunger that pushes water and water charged with variables. judging that the longer the contact time, the greater the energy transferred to the steel ball. As a result of experiments with each variable, the amount of water does not affect the speed acceleration efficiency of the steel ball and, when the length of the plunger is increased by 200 %, the speed of the steel ball can be accelerated up to 130 m/s.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.4
• /
• pp.395-401
• /
• 2015

A mini ball launch system was developed for the study of dynamic fracture of ceramic materials. The principle of velocity multiplication system is similar to two stage gun. The plastic sabot assembly houses steel plunger and the void filled with silicone rubber. The sabot is stopped by the stopper block then the steel plunger inside the sabot compress the silicone rubber to high pressure. Then the compressive energy of the silicone rubber is transferred to the ball. More than ten times of initial speed was attained. In this study, most effective silicone rubber for the highest final speed was chosen out of three different varieties by launch tests.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.6
• /
• pp.68-74
• /
• 2002

This research covers the development of axi-symmetric plastic elements for injection molding with insert steel such as high stiffness Sabot. The functional requirements of sabot are concentricity and fracture resistance about vertical and horizontal forces. For these, an analysis of characteristics of PEI(polyetherimide) polymer is performed by standard test specimen with accordance of ASTM test guidance. Moldflow analysis and simulation of injection molding process are carried out in order not only to estimate of the warpage but also to predict the characteristics of residual stresses which both product and structure of mold may have. A new vertical side injection machine and transverse mold have been constructed. Results of the measuring concentricity and fracture test after molding of sabot are satisfied to design specification over Cp $ratio{\geq}1.33$. Finally, this technique needs more research application to others axi-symmetric elements having different radius with insert steel md structure analysis from now on.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.2
• /
• pp.92-98
• /
• 1999

Dynamic behavior of missile which is fired in canister is analyzed by flexible multibody dynamics. The bending elasticity of missile is very important in case that missile is fired in the inclined launcher. In this paper, the force element model for the missile launching stage and the finite element model of missile are developed. The FEA model of missile is condensed into five lumped mass element model and the consistence between FE model and lumped mass model of missile is verified by modal analysis. As a result of analysis, sabot reaction force and pitch rate of missile for the variation of gap size and force element are obtained.