• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.404-409
• /
• 2006

The catalytic combustion of toluene over Pd-Cu/USY zeolite has been examined by using FT-IR spectroscopy in a closed system under dry and humid conditions. The catalytic combustion of toluene (700 ppmv) in the temperature range of $80-220^{\circ}C$ has been investigated by using a fixed bed reactor. The Pd-Cu/USY catalyst showed the highest catalytic performance with respects to the PdO-CuO/USY and Pd/USY. Comparing to $PdO/Al_2O_3$ catalysts, the slight improvement in conversion was observed over PdO/USY catalysts under humid condition since USY zeolite is hydrophobic substrate and water give an additional oxygen source to zeolite surface like oxygen. The reduced catalysts showed more enhanced catalytic activity due to the reduced activation energy of combustion of toluene than oxidized catalysts such as PdO/USY and PdO-CuO/USY.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.6
• /
• pp.143-154
• /
• 2012

The wireless low-floored tram is an innovative transportation system which is environment-friendly and highly energy-efficient. In addition, the system has various advantages such as low construction cost, improvement of urban landscape, revitalization of surrounding commercial area, elevated convenience for passengers, etc. Therefore, more than ten local governments have proposed tram construction projects in Korea. Accordingly, many research and development projects are ongoing funded by government including the developments of tram vehicle, tram trackway, signal system, etc. The embedded rail system are commonly used in order to provide leveled roadway surface in urban area. It is effective to reduce the noise and vibration, caused at the interface between the wheel and track, to minimize the construction period, and to lower the maintenance cost. This paper investigated the design and construction processes for tram trackway and figured out the constructability for the test track with embedded rail system for the first time in Korea. The performance to reduce the noise and vibration were quantitatively measured in the test track with embedded rail system. In addition, the results were compared to the ones for track with conventional rail system.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.11 no.2
• /
• pp.61-72
• /
• 2008

Leaf area index (LAI) is a key biophysical variable influencing land surface processes such as photosynthesis, transpiration and energy balance, and is a required input to estimate evapotranspiration in various ecological and hydrological models. The development of more correct and useful LAIs estimation techniques is required by these importance, but LAIs had been assumed in most LAI research through simple relations with the normalized difference vegetation index (NDVI) because the field measurement is difficult on wide area. This paper is to evaluate the MODIS LAI Product's practical use by comparing with LAIs that is derived from NOAA AVHRR NDVIs and the 2 years (2003-2004) measured LAIs of Korea Forest Research Institute in Gyeongancheon watershed (561.12 $Km^2$). As a result, the MODIS LAIs of deciduous forests showed higher values about 14 % and 15~30 % than the measured LAIs and NOAA LAIs. In the year of 2003, the MODIS LAIs in coniferous forests were 5 % higher than the measured LAIs, and showed about 7 % differences comparing with the NOAA LAIs except April. These differences come from the insufficient field data measured in partial points of the target area, and the extracted reference data from MODIS LAIs include the limits of spatial resolution and the error of incorrect land cover classification. Thus, using the MODIS data by the proper correction with the measured data can be useful as an input data for ecological and hydrological models which offers the vegetation information and simulates the water balance of a given watershed.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.3
• /
• pp.118-124
• /
• 2001

The Langmuir adsorption isotherm of the over-potentially deposited hydrogen (OPD H) for the cathodic $H_2$ evolution reaction (HER) at the $poly-Au|0.5M\;H_2SO_4$ aqueous electrolyte interface has been studied using cyclic voltammetric and ac impedance techniques. The behavior of the phase shift $(0^{\circ}\leq{-\phi}\leq90^{\circ})$ for the optimum intermediate frequency corresponds well to that of the fractional surface coverage $(1\geq{\theta}\geq0)$ at the interface. The phase-shift profile $({-\phi}\;vs.\;E)$ for the optimum intermediate frequency, i.e., the phase-shift method, can be used as a new method to estimate the Langmuir adsorption isotherm $(\theta\;vs.\;E)$ of the OPD H for the cathodic HER at the interface. At the poly-$Au|0.5M\;H_2SO_4$ electrolyte interface, the equilibrium constant (K) and standard free energy $({\Delta}G_{ads})$ of the OPD H are $2.3\times10^{-6}\;and\;32.2\;kJ\;mol^{-1}$, respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.12
• /
• pp.877-882
• /
• 2013

The application of ultrafiltration (UF) and microfiltration (MF) membranes has been increased for drinking water purification. The advantages of UF/MF membrane process compared to conventional treatment processes are stable operation under varying feed water quality, smaller construction area, and automatic operation. Most membrane treatment plants are designed with polymeric membranes. Recently, some studies suggested that the process of treating surface water with ceramic membranes is competitive to the application of polymeric membranes. Higher water flux, less frequent cleaning, and much longer lifetime are the advantages of ceramic membrane comparing to polymeric membrane. Therefore, this research focused on the application of ceramic MF membrane pilot plant at the slow sand filtration plant. The ceramic membrane pilot plant has three trains that used raw water and sand filtered water as a feed water, respectively. For optimizing the pilot plant process, the coagulation with PACl coagulant was used as a pretreatment of ceramic membrane process. In addition, CEB (Chemical Enhanced Backwash) process using $H_2SO_4$ and NaOCl was used for 1.5 days, respectively. The experimental results showed that applying the optimum coagulant dose before membrane filtration showed enhancing membrane fluxes for both raw water and sand filtered water. Also, when using raw water as a feed of membrane, minimum fouling rate was 2.173 kPa/cycle with 25 mg/L of PACl and when using sand filtered water, the minimum fouling rate was 0.301 kPa/cycle with 5 mg/L of PACl.

• Applied Microscopy
• /
• v.19 no.2
• /
• pp.119-137
• /
• 1989

It has been shown in this and earlier investigation that the turtle bladder mucosa has three main cell types on their mucosal surface. They are the granular cells, ${\alpha}$ CA cells, and ${\beta}$ CA cells. The three major transport mechanisms that occurs in the turtle bladder are sodium reabsorption, proton secretion, and bicarbonate secretion. In the present work the trans-port mechanisms by bladder epithelial cells of freshwater turtle, Pseudemys scripta, are summarized as follows. 1. The granular cells play an important role in sodium transport, while the ${\alpha}$ and ${\beta}$ CA cells do not appear to play a determining role in sodium transport. 2. It appears that the active sodium transport in the granular cells occurs in two-step process, implying that first, sodium diffuses into the cells, followed by an energy-dependent efflux step, which is catalyzed by the ouabain-sensitive Na-K ATPase. 3. The ${\alpha}$ type of CA cells are responsible for the proton secretion using the proton pump on the apical plasma membrane, while the ${\beta}$ type of CA cells are believed to be responsible for bicarbonate secretion. 4. When looked at under freeze-fracture electron microscopy, the apical plasma membrane of ${\alpha}$ cells have a characteristic population of rod-shaped intramembranous particles which are believed to be components of the proton pumps. Conversely, ${\beta}$ type of CA cells show rod-shaped particles in their basolateral plasma membranes, which is consistent with the proton absorptive, bicarbonate secretory mechanism. 5. In the turtle bladder, the ${\alpha}$ and ${\beta}$ type of cells are believed to be both responsible for proton transport, but in opposite directions.

• Journal of Veterinary Clinics
• /
• v.22 no.1
• /
• pp.21-25
• /
• 2005

This study was performed to assess therapeutic effect of the tibial plateau leveling osteotomy (TPLO) in dogs with experimentally transected cranial cruciate ligaments (CrCL). Nine healthy adult Beagle dogs were transected left CrCL under general anesthesia. The dogs were assigned to TPLO and non-TPLO control groups. The TPLO procedures for correcting the CrCL rupture in the left stifle of dogs were performed under sterile conditions. Before TPLO procedures, all dogs were screened by orthopedic and radiographic examinations. Dogs were lameness free for the previous three months, and when examined at the walk and trot on a hard surface, in a straight line and on a circle. Lateral and craniocaudal radiographs were done to confirm the soundness of the both knee joint in dogs and not detectable lesions were diagnosed. The dogs were intravenously injected with a 10 mci/kg of 99mTechnetium-methylene diphosphonate (99mTc-MDP) under general anesthesia. Scintigraphs were obtained using a large field of view gamma camera equipped a parallel-hole, low-energy about 3 hours after intravenous injection of 99mTc-MDP. Before CrCL transection and 4, 8, and 12 weeks after the procedures, scintigraphy were conducted. Bone uptake of the left stifle joint increased after the procedures in all dogs. When the bone uptake from the TPLO procedure was compared with that of the control, there was a significant difference (p < 0.05). At 12 weeks after the TPLO procedure, the dogs showed normal anatomical posture and gait. It is concluded that TPLO procedure was effective in reconstruct of the stifle joint in dogs with CrCL rupture.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.26 no.2
• /
• pp.225-236
• /
• 2016

Objectives: Nanomaterials have been used in various fields. As use of nanoproducts is increasing, workers dealing with nanomaterials are also gradually increasing. Exposure assessments for nanomaterials have been carried out for protection of worker's health in workplace. Exposure studies were mainly focused on manufacturing processes, but these studies on after-treatment processes such as refinement, weighing, and packing were insufficient. So, we investigated exposure characteristics of particles during after-treatment processes of $Al_2O_3$ fibers and Ni powders. Methods: Mass-production of Ni powder process was carried out in enclosed capture-type canopy hood. In a developing stage, $Al_2O_3$ was handled with a local ventilation unit. Exposure characteristics of particles were investigated for $Al_2O_3$ fiber and Ni powder processes during the periods of 10:00 to 16:00, 20 May 2014 and 13:00 to 16:00, 21 May 2014, respectively. Three real-time aerosol instruments were utilized in exposure assessment. A scanning mobility particle sizer(SMPS, nanoscan, model 3910, TSI) and an optical particle counter(OPC, portable aerosol spectrometer, model 1.109, Grimm) were used to determine the particle size distribution in the size range of 10-420 nm and $0.25-32{\mu}m$, respectively. In addition, a nanoparticle aerosol monitor(NAM, model 9000, TSI) was used to measure lung-deposited nanoparticle surface area. Membrane filters(isopore membrane filter, pore size of 100 nm) were also used for air sampling for the FE-SEM(model S-5000H, Hitachi) analysis using a personal sampling pump(model GilAir Plus by 2.5 L/min, Gilian). Conclusions: For Ni powder after-treatment process, only 27% increase in particle concentration was found during the process. However, for $Al_2O_3$ fiber after-treatment process, significant exposure(1.56-3.34 times) was observed during the process.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.835-841
• /
• 2013

Modern solid-state gyroscopes (HRG) with hemispherical resonators from high-purity quartz glass and special surface superfinishing and ultrathin gold coating become the best instruments for precise-grade inertial reference units (IRU) targeting long-term space missions. Designing of these sensors could be a notable contribution into development of Korea as a space nation. In participial, 40mm diameter thin-shell resonator from high-purity fused quartz, fabricated as a single-piece with its supporting stem has been designed, machined, etched, tuned, tested, and delivered by STM Co. (ATS of Ukraine) several years ago; an extremely-high Q-factor (upto 10~20 millions) has been shown. Understanding of the best way how to match such a unique sensor with inner glass assembly of the gyro means how to use the high potential in a maximal extent; and this has become the urgent task. Inner quartz glass assembly has a very thin indium (In) layer soldered the resonator and its silica base (case), but effects of internal resonances between operational modal pair of the shell-cup and its side (parasitic) modes can notable degrade the potential of the sensor as a whole, instead of so low level of resonator's intrinsic losses. Unfortunately, there are special combinations of dimensions of the parts (so-called, "resonant sizes"), when intensive losses of energy occurs. The authors proposed to use the length of stem's fixture as an additional design parameter to avoid such cases. So-called, a cyclic scheme of finite element method (FEM) and ANSYS software were employed to estimate different combinations of gyro assembly parameters. This variant has no mismatches of numerical origin due to FEM's discrete mesh. The optimum length and dangerous "resonant lengths" have been found. The special attention has been paid to analyses of 3D effects in a cup-stem transient zone, including determination of a difference between the positions of geometrical Pole of the resonant hemisphere and of its "dynamical Pole", i.e., its real zone of oscillation node. Boundary effects between the shell (cup) and 3D short "beams" (inner and outer stems) have been ranged. The results of the numerical experiments have been compared with the classic model of a quasi-hemispherical shell band with inextensional midsurface, and the solution using Rayleigh's functions of the $1^{st}$ and $2^{nd}$ kinds. To guarantee the truth of the recommended sizes to a designer of the real device, the analytical and FEM results have been compared with experimental data for a party of real resonators. The consistency of the results obtained by different means has been shown with errors less than 5%. The results notably differ from the data published earlier by different researchers.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.267-275
• /
• 1997

$ZrO_2$ Powder was Prepared by sol-gel process and the adsorption characteristic of cobalt($Co^{2+}$) by $ZrO_2$ adsorbent in high-temperature water was investigated using batch adsorption experiment with a stirred autoclave. The prepared $ZrO_2$ was calcined at $600{\sim}1400^{\circ}C$ and analyzed by X-ray diffractometry, SEM, BET surface area, FT-IR and TG-DTA measurement. The tetragonal Phase of $ZrO_2$ is produced $480^{\circ}C$ from amorphous gel at temperature $480^{\circ}C$. Both tetragonal and monoclinic phase of $ZrO_2$ exist at temperature between $600^{\circ}C$ and $1000^{\circ}C$. At temperature $1200^{\circ}C$, tetragonal to monoclinic phase trasition is occurred. The $Co^{2+}$ adsorption capacity of $ZrO_2$ calcined at $600^{\circ}C$ for 4 hours is 0.16 meq $Co^{2+}/g$ adsorbent in the high temperature at $250^{\circ}C$. The adsorption of $Co^{2+}$ on the $ZrO_2$ adsorbent is irreversible endothermic in the temperature range ($125-175^{\circ}C$). The standard enthalpy change (${\Delta}H^{\circ}$) of $ZrO_2$ calcined at $600^{\circ}C$ for 4 hours is 18 kJ/gmol.