• Journal of the Korean Magnetics Society
• /
• v.8 no.1
• /
• pp.13-20
• /
• 1998

The crystallographic and high frequency characteristics of $Fe_{73.9}Cu_{1.0}Nb_{3.5}Si_{14.0}B_{7.6}$ soft magnetic alloys were investigated under the magnetic field annealing. As-cast ribbon with which already imbedded nanocrystalline Fe-Si phase on the surface have a preferred orientation with (400) plane to surface and also with the [011] direction parallel to the ribbon length. The extra nanocrystalline Fe-Si phase appeared throughout at 45$0^{\circ}C$ in samples with or without the longitudinal magnetic field. However the formation of nanocrystalline phase does not appear on the suface layer until 50$0^{\circ}C$ annealing temperature under the transverse field. The cryststallization fraction of annealed samples with longitudinal magnetic field is higher than that of samples without magnetic field. When the transverse magnetic field is applied, the crystallization fraction does not increases but decreases until 50$0^{\circ}C$. However the crystallization of internal regions can be confirmed by X-ray diffraction measurement via tilting the sample. It was found that for all samples, the saturation induction were all same with 1.3 T. The coercive field of as-cast sample was 1.06 A/cm, but in annealed samples it decrease from 0.56 to 0.1 A/cm with increasing annealing temperature from 400 and 55$0^{\circ}C$, respectively. The squareness of annealed samples under transverse magnetic field has a small value than that of both without field and with longitudinal field annealing.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.2
• /
• pp.147-151
• /
• 2023

Transparent ZnO (100 nm thick) and ZnO/Ti/ZnO (ZTZ) films were prepared with radio frequency (RF) and direct current (DC) magnetron sputtering on the glass substrate at room temperature. During the ZTZ film deposition, the thickness of the Ti interlayer was varied, such as 6, 9, 12, and 15 nm, while the thickness of ZnO films was kept at 50 nm to investigate the effect of the Ti interlayer on the crystallization and opto-electrical performance of the films. From the XRD pattern, it is concluded that the 9 nm thick Ti interlayer showed some characteristic peaks of Ti (200) and (220), and the grain size of the ZnO (002) enlarged from 13.32 to 15.28 nm as Ti interlayer thickness increased. In an opto-electrical performance observation, ZnO single-layer films show a figure of merit of 1.4×10^-11 Ω^-1, while ZTZ films with a 9 nm-thick Ti interlayer show a higher figure of merit of 2.0×10^-5 Ω^-1.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.49 no.2
• /
• pp.97-106
• /
• 2023

In this study, we would like to study the stabilization of the high content of ceramide formulation by containing cyclodextrin. Ceramide, which constitutes the intercellular lipid, a human skin barrier, is a very important ingredient in moisturizing maintenance by protecting moisture in the skin and strengthening the skin barrier. However, since ceramide is poorly soluble, even if it is included in the cosmetic formulation, it has a problem that it is slowly gelled or crystallized and deposited over time, making it difficult to containing a high amount of ceramide. Cyclodextrin is a cyclic oligosaccharide connected with glucose molecules and has a cylindrical structure with hydrophilic outer surface and hydrophobic inner surface, which is known to improve the physicochemical properties of drugs such as improving solubility and absorption of poorly soluble drugs. We demonstrated the stability of the formulation containing high amount of ceramide by measuring hardness and observing emulsion drops with polarized microscope. This study also demonstrated that the high-content ceramide formulation containing cyclodextrin has the effect of preventing gelation or crystallization of ceramide, thus having excellent environmental conditions stability and skin moisturization.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.115-119
• /
• 2008

Single particle of nickel hydroxide and the surface-treated one with cobalt element were performed to review the effect of LiOH additive in alkaline electrolyte for Ni-MH batteries using microelectrode test system. As a result of cyclic voltammetry, the electrochemical behaviors such as the oxidation/reduction and oxygen evolution reaction are clearly observed for a single particle of nickel hydroxide, respectively. Furthermore, the reduction current peak of nickel hydroxide added with LiOH in electrolyte was very low and broad compared with the normal nickel hydroxide without an additive LiOH, which had a bad effect to the crystallization structure of nickel hydroxide. However, it was found that capacity and cycle properties of the nickel hydroxide treated with cobalt greatly increased by the addition of LiOH.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.26 no.2
• /
• pp.81-88
• /
• 2013

Wet-spun silk fibers have attracted the attention of many researchers because of 1) the unique properties of silk as a biomaterial, including good biocompatibility and cyto-compatability and 2) the various methods available to control the structure and properties of the fiber. Cellulose nanofibrils (CNFs) have typically been used as a reinforcing material for natural and synthetic polymers. In this study, CNF-embedded silk fibroin (SF) nanocomposite fibers were prepared for the first time. The effects of CNF content on the rheology of the dope solution and the characteristics of wet-spun CNF/SF composite fibers were also examined. A 5% SF formic acid solution that contained no CNFs showed nearly Newtonian fluid behavior, with slight shear thinning. However, after the addition of 1% CNFs, the viscosity of the dope solution increased significantly, and apparent shear thinning was observed. The maximum draw ratio of the CNF/SF composite fibers decreased as the CNF content increased. Interestingly, the crystallinity index for the silk in the CNF/SF fibers was sequentially reduced as the CNF content was increased. This phenomenon may be due to the fact that the CNFs prevent ${\beta}$-sheet crystallization of the SF by elimination of formic acid from the dope solution during the coagulation process. The CNF/SF composite fibers displayed a relatively smooth surface with stripes, at low magnification (${\times}500$). However, a rugged nanoscale surface was observed at high magnification (${\times}10,000$), and the surface roughness increased with the CNF content.

• Journal of Powder Materials
• /
• v.21 no.4
• /
• pp.251-255
• /
• 2014

In this study, we optimized dissolution the dissolution conditions of porous amorphous powder to have high specific surface area. Porous metallic glass(MG) granules were fabricated by selective phase dissolution, in which brass is removed from a composite powder consisting of MG and 40 vol.% brass. Dissolution was achieved through various concentrations of $H_2SO_4$ and $HNO_3$, with $HNO_3$ proving to have the faster reaction kinetics. Porous powders were analyzed by differential scanning calorimetry to observe crystallization behavior. The Microstructure of milled powder and dissolved powder was analyzed by scanning electron microscope. To check for residual in the dissolved powder after dissolution, energy dispersive X-ray spectroscory and elemental mapping was conducted. It was confirmed that the MG/brass composite powder dissolved in 10% $HNO_3$ produced a porous MG granule with a relatively high specific surface area of $19.60m^2/g$. This proved to be the optimum dissolution condition in which both a porous internal granule structure and amorphous phase were maintained. Consequently, porous MG granules were effectively fabricated and applications of such structures can be expanded.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.2
• /
• pp.77-86
• /
• 2000

In this study effects of La starting compounds and substrates on the densification of (P $b_{0.92}$L $a_{0.05}$)Ti $O_3$ thin films were investigated. After the heat treatment on platinized silicon at $650^{\circ}C$ for 30min thickness of PLT(i) thin films (from La-isopropoxide) shrank by 27%, while 33% reduction occurred for PLT (a) thin films (from La-acetate). These PLT(i) films showed less densified surface microstructure compared to the PLT (a) . Lower shrinkage of the films on platinized silicon than on bare silicon (41% and 40% for PLT (i) and PLT (a) respectively) is attributed to the earlier development of crystallinity in the film, which arrests film densification. In order to maximize sintering before crystallization, heat treatment at $400^{\circ}C$ for 3 hours followed by $650^{\circ}C$ for 30 min was attempted. This method increased the shrinkage of the PLT (i) and PLT (a) films two times and 1.5 times as much as that observed for the films heat treated at $650^{\circ}C$ for 30min, respectively. FTIR results indicated that first pyrolysis in the film is associated with the burning of acetate ligands. Condensation reaction between OHs was found to occur preferentially between $350^{\circ}C$ and $450^{\circ}C$, whereas majority of polycondensation between ROH-OH appears to occur until $300^{\circ}C$ and be completed below $450^{\circ}C$.EX>.

• Applied Chemistry for Engineering
• /
• v.9 no.7
• /
• pp.998-1003
• /
• 1998

$BaTiO_3$ thin film was electrochemically deposited on Ti electrode in a 0.4 M $Ba(OH)_2$ solution of $85^{\circ}C$ using a current pulse waveform. Both $BaTiO_3$ crystallinity and faradaic efficiency for the film formation were enhanced with the increase of cathodic current density and pulse time. Based on the surface analysis and electrochemical studies, it was suggested that, during cathodic pulsed, the surface pH increase due to the reduction of $H_2O$ accelerates the structural changes of Ti oxides which were formed during anodic cycle. Prior to experiments, Ti oxides were intentionally grown in 0.1 M $H_2SO_4$ solution and the effect of initial oxide film thickness on the $BaTiO_3$ film formation was investigated. The migration of $Ti^{+4}$ ions through the oxide film was retarded with the increase of film thickness and it was observed that the crystallization of $BaTiO_3$ was only limited to the defect area of surface oxides.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.3
• /
• pp.128-132
• /
• 2009

Transparent conducting thin films of indium tin oxide(ITO) co-sputtered with aluminum-doped zinc oxide(AZO) were deposited on glass substrate by dual magnetron sputtering. It was found that the electrical properties and structural characteristics of the films are significantly changed according to the sputtering power of the AZO target. The IAZTO film prepared with D.C power of ITO at 100 W and R.F power of AZO at 50 W shows an electrical resistivity of $4.6{\times}10^{-4}{\Omega}{\cdot}cm$ and a sheet resistance of $30{\Omega}/{\square}$ (for 150 nm thick). Besides of the improvement of the electrical properties, compared to the ITO films deposited at the same process conditions, the IAZTO films have very smooth surface, which is due to the amorphous nature of the films. However, the electrical conductivity of the IAZTO films was found to be deteriorated along with the crystallization in case of the high temperature deposition (above $310^{\circ}C$). In this work, high quality amorphous transparent conductive oxide layers could be obtained by mixing AZO with ITO, indicating possible use of IAZTO films as the transparent electrodes in OLED and flexible display devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.5
• /
• pp.392-397
• /
• 2011

The effect of various post-annealing temperature to sputtered Pb(Zr,Ti)$O_3$ (PZT) thin films was investigated. The crystallization process, surface morphology and the electrical characteristics strongly depends on the rapid thermal annealing (RTA). In radio frequency (RF) sputtering methods, there were many papers mostly forcing on the crystal forming and the surface variations with different elements distribution (Pb, Ti, Zr, O) on the surface of the PZT layer. In this experiment, the post-annealing treatment promoted the Pb volatilization in PZT thin film and affected the Ti diffused throughout the Pt layer into the PZT layer. Second ion mass spectroscopy (SIMS) analysis was employed to show that the Pb element in the PZT layer was decreased at the same time the Ti element mass was slight decreased than Pb with increasing RTA temperature. That result prove the content of Pb affect the PZT thin film property.