• Journal of Welding and Joining
• /
• 제9권4호
• /
• pp.17-27
• /
• 1991

The direct brazing technology which could be used for the simplification of brazing process and the improvement of brazed joint quality was studied with $Al_2O_3$ and stainless steels. The brazing of $Al_2O_3$ to STS304 or STS430 was performed under different brazing conditions such as brazing filler metal, temperature, heating rate and brazing time. Microstructural observation and chemical analysis be SEM/EPAM were carried out to verify the quality of brazed joints. 4-point bending strength of brazed joints was also measured to find the optimal brazing conditions. The results showed that, in brazing of $Al_2O_3$, the mixed oxide layer resulted from the reaction between Ti in filler metal and oxide layer on the material surface to be brazed was found to be bery important for the joint quality. The width of oxide layer varied with the brazing conditions such as brazing time, heating rate and chemical composition of filler metals. The strength of brazed joints was more affected by the type of materials and their thermal properties than by brazing heat cycle.

• 한국정밀공학회지
• /
• 제13권5호
• /
• pp.53-59
• /
• 1996

Warm deep drawing of single-action dies using local heating has appeared to be an alternative attractive production method of multi-operation die sets generally used at room temperature in deep drawing of rectangular cup. Uniaxial tensile tests and deep drawing tests of various materials are carried out and the effect of temperature on tensile properties and drawability are examined at temperatures up to 200 .deg. C under three kinds of lubricants of teflon film, vinyl film and drawing oil. Good formability is achieved when punch and die temperature were differentiated intentionally in order to get large tensile strength(TS) at punch shoulder protion and small TS at die side. Throughout the experiments, it has been shown that the limiting drawing height of STS316L was increased with heating die and blank holder at 100 .deg. C, but that of STS430 wasn't. When vinyl or teflon film was attached on the plates, the drawability was increased considerably.

• 한국분말재료학회지
• /
• 제18권3호
• /
• pp.290-296
• /
• 2011

Titanium carbonitride is more perspective materials compared to titanium carbide. It can be used in tool industry and special products because of its higher strength, abrasive wear-resistance and especially its strong chemical stability at high temperatures. We produced STS+TiCxNy composite by the spark plasma sintering for higher strength and studied the characteristics. The planar and cross-sectional microstructures of the specimens were observed by scanning electron microscopy. Characterizations of the carbon and nitride phases on the surface of composite were carried out using an X-ray diffractometer. During annealing TiCxNy particles diffusion into STS 430 was observed. After annealing, sintering isolations between particles were formed. It causes decreasing of mechanical strength. In addition when annealing temperature was increased hardness increased. Heterogeneous distribution of alloying elements particles was observed. After annealing composites, highest value of hardness was 738.1 MHV.

• 전기화학회지
• /
• 제6권4호
• /
• pp.250-254
• /
• 2003

본 연구는 전기화학적 실험측정으로 페라이트계 430스테인레스강 시험편에 인위적으로 틈을 형성시켰다. 부식용액은 IN $H_2SO_4+0.1N\;NaCl$ 전해액을 사용하였고, 각 시험편의 틈의 크기를 달리하였다. 전기화학적 평가방법은 -600mV/5CE에서 정방향으로 +1,200mV/SCE까지 주사속도 600mV/hr로 동전위 분극시험을 실시하여 부식전위, 부동태 전류밀도 등의 부식거동을 분석하였다. 그리고 정전위 분극시험을 실시하여 부동태 구간 전위 -200mV/SCE를 일정하게 인가 한 후, 틈내에 부동태 전류밀도와 틈부식 발생시간을 계측하였다 실험방법에 있어 Microcapillary tube(MCT)를 이용한 방법으로 틈내 각 지점의 전위를 틈 깊이에 따른 틈내부의 전위강하(IR Drop)에 주목하고, 575 430 스테인레스강 금속에 대한 분극특성과 연계하므로써 틈부식의 발생 원인을 '전위의 이동'의 관점에서 규명 하였다.

• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.512-519
• /
• 2001

Sink roll has been used in molten Zn-0.2%Al alloy bath of continuous galvanizing line in sinking and stabilizing process of the steel strip in molten metal bath. In this process, although the scraper scraps off the sink roll surface, the dross compounds is builded up on the sink roll surface and the life time of the sink roll is shorten by the dross compounds. The present study was investigated the application of the spray coating layer on sink roll body for improving durability In molten Zn-0.2%Al alloy. Through the durability tests in molten Zn-0.2%Al alloy with various ceramic and cermet coating layer, the optimum bond and top coating material was obtained. As the results, the system of STS430F base metal, WC-l7Co bond and $ZrO_2-SiO_2$ top coating was clarified to be the best quality of durability in molten Zn-0.2%Al alloy.

• 한국재료학회지
• /
• 제20권7호
• /
• pp.356-363
• /
• 2010

For this paper, we investigated the area specific resistance (ASR) of commercially available ferritic stainless steels with different chemical compositions for use as solid oxide fuel cells (SOFC) interconnect. After 430h of oxidation, the STS446M alloy demonstrated excellent oxidation resistance and low ASR, of approximately 40 $m{\Omega}cm^2$, of the thermally grown oxide scale, compared to those of other stainless steels. The reason for the low ASR is that the contact resistance between the Pt paste and the oxide scale is reduced due to the plate-like shape of the $Cr_2O_3$(s). However, the acceptable ASR level is considered to be below 100 $m{\Omega}cm^2$ after 40,000 h of use. To further improve the electrical conductivity of the thermally grown oxide on stainless steels, the Co layer was deposited on the stainless steel by means of an electroless deposition method; it was then thermally oxidized to obtain the $Co_3O_4$ layer, which is a highly conductive layer. With the increase of the Co coating thickness, the ASR value decreased. For Co deposited STS444 with 2 ${\mu}m$hickness, the measured ASR at $800^{\circ}$ after 300 h oxidation is around 10 $m{\Omega}cm^2$, which is lower than that of the STS446M, which alloy has a lower ASR value than that of the non-coated STS. The reason for this improved high temperature conductivity seems to be that the Mn is efficiently diffused into the coating layer, which diffusion formed the highly conductive (Mn,Co)$_3O_4$ spinel phases and the thickness of the $Cr_2O_3$(S), which is the rate controlling layer of the electrical conductivity in the SOFC environment and is very thin

• 한국강구조학회 논문집
• /
• 제28권5호
• /
• pp.303-312
• /
• 2016

최근에 스테인리스강의 우수한 연성과 내식성 등의 재료적 특성으로 건축물의 구조용 강재로 적용하기 위한 많은 연구들이 수행되어 오고 있다. 특히, 니켈을 거의 함유하고 있지 않은 페라이트계 스테인리스강은 재료비 측면에서 니켈을 함유하고 있는 오스테나이트계 스테인리스강에 비해 저렴하고 탄소강에 비해서는 월등한 내식성능과 구조성능을 제공하기 때문에 그 사용성이 증대되고 있다. 본 연구에서는 페라이트계 스테인리스강 용접접합부에 있어 용착금속이 아닌 모재 블록전단파단의 구조적 거동을 조사하기 위해 용접길이와 용접방법(아크, 티그)을 변수로 하여 단순인장 실험을 실시하였다. 용접접합부의 블록전단 거동은 용접에 의한 삼축응력효과 때문에 볼트접합부의 블록전단 거동과 상이하며, 현행설계기준식은 이러한 특성을 반영하지 못하고 있다. 티그용접 접합부의 변형능력과 최대내력이 아크용접 접합부보다 높게 나타났고, 현행기준식과 기존연구자에 의해 제시된 내력식에 의한 예측내력과 실험결과 최대내력을 비교 검토하였다.

• 한국식품위생안전성학회지
• /
• 제35권5호
• /
• pp.430-437
• /
• 2020

본 연구는 전자코와 전자혀 시스템을 이용한 15가지 국내 식품에 대한 맛과 향에 대한 기본 접근 연구를 진행하였다. 먼저 전자혀 시스템을 이용한 샘플의 맛 성분에 대해 상대적인 센서 강도를 제시하였다. 신맛으로 대표되는 SRS 센서에서는 소고기배추국이 가장 높은 9.0을 나타내었고, 미역국에서 가장 낮은 3.7을 나타내었다. 짠맛으로 대표되는 STS 센서는 오징어국에서 가장 높은 8.2를 나타내었고, 소고기배추국이 가장 낮은 1.9를 나타내었다. 감칠맛으로 확인되는 UMS 센서의 경우 소고기배추국이 가장 높은 10.1을 보였고, 달걀국이 가장 낮은 3.3을 나타내었다. 단맛에 관여하는 SWS 센서에서는 비교적 큰차이를 보이지 않았는데, 시금치된장국이 가장 높은 7.3을 나타내었고, 달걀국이 가장 낮은 4.6을 나타내었다. 마지막으로 쓴맛에 기여하는 BRS 센서에서는 시래기 된장국이 가장 높은 7.8을 나타내었으며, 햄김치찌개에서 가장 낮은 4.4를 보였다. 주성분 분석을 통해 5가지 맛 성분과 15가지 샘플에 대한 패턴을 확인한 결과 PC1에서 56.21%의 variance를 확인하였고, PC2에서 25.23%의 variance를 확인할 수 있었다. 각 맛 성분의 경우 SRS 센서의 경우 PC1과 PC2의 factor loading의 경우 -0.95와 -0.20을 나타내었고, STS 센서의 경우 PC1과 PC2의 factor loading의 값이 0.96과 0.14, UMS 센서의 경우 PC1과 PC2의 factor loading의 값이 -0.94와 0.22, SWS 센서의 경우 PC1과 PC2의 factor loading의 값이 0.08과, 0.89, 그리고 BRS 센서의 경우 PC1과 PC2의 factor loading의 값이 0.32와 -0.60을 각각 나타내었다. 군집분석을 통해 확인된 샘플간의 유사도는 크게 4개의 cluster를 확인할 수 있었다. 15가지 샘플에서 확인된 향기성분은 총 25가지 성분이 확인되었고, 모든 샘플에서 상대적으로 가장 높은 함량을 보이는 향기성분은 ethanol과 2-methylthiophene으로 확인되었다. 주성분 분석을 통해 휘발성 향기 성분과 15가지 샘플에 대한 패턴을 확인한 결과 PC1에서 28.54%의 variance를 확인하였고, PC2에서 20.80%의 variance를 확인할 수 있었다. 군집분석의 경우 크게 3개의 cluster로 분류되는 것을 확인할 수 있었다. 이러한 맛과 향에 대한 연구를 통해서 국내 식품에 대한 표준 자료로써의 활용이 가능할 것으로 판단된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2222-2227
• /
• 2007

Newly structured metal-supported solid oxide fuel cell was fabricated and characterized by impedance analysis and galvanodynamic experiment. Using a cermet adhesive, thin ceramic layer composed of anode(Ni/YSZ) and electrolyte(YSZ) was joined with STS430 metal support of which flow channel was fabricated. $La_{0.8}Sr_{0.2}Co_{0.4}Mn_{0.6}O_3$ perovskite oxide was used as cathode material. Single cell performance was increased and saturated at operating time to 300hours at 800$^{\circ}C$ because of cathode sintering effect. The sintering effect was reinvestigated by half cell test and exchange current density was measured as 0.005A/$cm^2$. Maximum power density of the cell was 0.09W/$cm^2$ at 800$^{\circ}C$. Numerical analysis was carried out to classify main factors influencing the single cell performances. Compared to experimental IV curve, simulated curve based on experimental parameters such as exchange current density was in good agreement.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.127-131
• /
• 2006

There are being a lot of studies for achievement of high speed Dehydration, high-strength and Lightweight of washing machine in the latest washing machine business. It is essential that Press-joining Strength of Spin Drum Seaming division is improved .to attain that target. Generally, we are using Mechanical press-joining by Seaming and T.I.G (Tungsten Inert Gas) welding among part joint method. Mechanical press-joining method that is mainly using for Stainless Steel (STS430) Drum have lots of merit that consumption of energy is low more than welding and production costs cut down and generation of the corrosion is solved by removing weld zone defect and materials having different properties are enable to join without special equipment. But, it is difficult to realize joint strength required at high speed operation because joint strength of mechanical press-joining method is low remarkably in comparison with welding. Also, there are a lot of analysis difficulties and very limited research is under way due to the dynamic factor such as multistage plastic working, elastic recovery, residual stress etc. The results of this study show optimal joining condition for mechanical press-joining by performing lots of tensile joining strength test with various specimen under multi-change of important design factor such as seaming width, bead area and bead depth etc.