• Korean Journal of Materials Research
• /
• v.31 no.1
• /
• pp.29-37
• /
• 2021

Martensitic stainless steel is commonly used in the medical implant instrument. The alloy has drawbacks in terms of strength and wear properties when applied to instruments with sharp parts. 440C STS alloy, with improved durability, is an alternative to replace 420 J2 STS. In the present study, the carbide precipitation, and mechanical and corrosion properties of STS 440C alloy are studied as a function of different heat treatments. The STS 440C alloy is first austenitized at different temperatures; this is immediately followed by oil quenching and sub-zero treatment. After sub-zero treatment, the alloy is tempered at low temperatures. The microstructures of the heat treated STS 440C alloy consist of martensite and retained austenite and carbides. Using EDX and SADP with a TEM, the precipitated carbides are identified as a Cr23C6 carbide with a size of 1 to 2 ㎛. The hardness of STS 440C alloy is improved by austenitization at 1,100 ℃ with sub-zero treatment and tempering at 200 ℃. The values of Ecorr and Icorr for STS 440C increase with austenitization temperature. Results can be explained by the dissolution of Cr-carbide and the increase in the retained austenite. Sub-zero treatment followed by tempering shows a little difference in the properties of potentiodynamic polarizations.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.5
• /
• pp.278-282
• /
• 2004

Effect of pre-treatment on the gas nitriding process of austenitic stainless steels has been investigated and the following results were obtained. Minimum pre-treatment time was decreased to 5min with increasing treatment temperature from $200^{\circ}C$ to $600^{\circ}C$. Surface activation effect by the pre-treatment was maintained in the air up to holding time of 64hr, judging from the analysis result of gas nitrided specimens. The Depth of nitrided layer of STS 304 and 316 stainless steels were ranged from $5{\mu}m$ to $90{\mu}m$ at $440^{\circ}C{\sim}600^{\circ}C$. The X-ray diffraction intensity for austenitic stainless steels were increases as nitriding temperature from $440^{\circ}C$ to $600^{\circ}C$.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.89-93
• /
• 1992

We experimented cutting characteristics-cutting force, behavior of chip, surface roughness-under low temperature, which generated by liquid nitrogen(77K). The results obtained are as follows; 1) The workpice is became to-195 .deg. C in 5, minutes, and in cooled cutting, cutting force bycooled workpices is stronger than normal temperature condition. Chip thickness is decreasing comparative toN.C and shear angle in shear plane is in creasing. 2) Chip formation becomes long or short tubular chips in turning SXM440, SNCM21 steel, when cutting speed is low and cutting temperatre is cooled condition, but in the STS304 steel the variation of c formations isn't known to. 3) In C.C, surface roughness of workpices is better than N.C and found to make more the crat wearthan N.C 4) It is possible to detect the behavior of chip by monitoring the maximum amplitude of gai value of cutting force.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.1
• /
• pp.44-53
• /
• 1994

We experimented on cutting characteristics-cutting force, behavior of cutting temprature, surface foughness, behavior of chips-under low tempdeature, which generated by liquid nitrogen (77K). The workpieces were freezed to -195 .deg. C and liquid nitrogen was also sprinkled on cutting area in order to increase the efficiency of machining in low temperature. The workpiece was became to -195 .deg. C in 5 minutes, and cutting temperature in CC was lower about 170 .deg. C than NC. The cutting force trended to increase slighty in cooled cutting, but chip thickness was decreased, shear angle was however increased. The form of chips was in good conditions of long or short tubular chips in CC. In CC surface roughness of workpiece was better than NC. In NC surface hardness of chips trended to increase according to increasing of cutting speed, but in CC it trended to decrease. The power spectrum of vertical cutting force trended to increase according to increasing of feed, and in CC it was higher than NC.

• Tribology and Lubricants
• /
• v.21 no.6
• /
• pp.278-282
• /
• 2005

Deep groove ball bearing is installed in a control element of an integral nuclear reactor, where water is used as coolant and lubricant. This bearing is made of STS440C stainless steel for the raceways and the balls to use in radioactive environment and water. It is known that the retainer design affects ball bearing operability and endurance life, however there is no verified retainer design and material for water lubricated ball bearing. Four kinds of retainers are manufactured for the endurance test of water lubricated deep groove ball bearing. Three of them are commercially developed types and the other is designed for this research. It is verified that ball bearings with steel pressed and general plastic retainer can not survive to required life in the water, however bearings with machined type and cylinder type retainer can survive. This proves that one of the major design parameters for water lubricated ball bearing is retainer type and material. In this paper, experimental research of endurance test for water-lubricated ball bearing are reported.