• KIEE International Transactions on Power Engineering
• /
• v.4A no.3
• /
• pp.109-114
• /
• 2004

In this paper, the H$\infty$ control method is applied in the control of SPFC and generators in order to obtain the robust stability performance of the power system. Moreover, a SPFC H$\infty$ controller based on loop shaping is designed to achieve first-rate tracking properties in addition to the robust stability. This robust control method is applied to a Ward and Hale 6-bus power system and the effects are analyzed. The MATLAB program is used for simulation of the robust controller.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.1
• /
• pp.27-31
• /
• 2014

As research development of seat frame is being studied actively, the total deformation of seat frame made of high tension steel plate(HTSP) is examined in this study. The seat frame made of SPFC 980 t=2mm with HTSP is tested to obtain total deformation through repeated fatigue durability tester and total deformation is analyzed by simulation under the same condition as experiment. After analyzing by comparing the results of experiment and analysis, structural stabilities of seat frame models with SPFC 780 t=2mm and SPFC 780 t=1.5mm are investigated by FEM analysis on the basis of these results. And it is considered that which model is more suitable at commercial use can be found through this study result.

• Journal of Power System Engineering
• /
• v.21 no.2
• /
• pp.5-13
• /
• 2017

This study has developed an organic/inorganic hybrid solution according to amount of $SiO_2$ polysilicate, and the amount of melamine is constant. The three types of cold rolled steel were evaluated a corrosion resistance properties by using these solutions. $US_3M_3$ and $US_{11}M_3$ solutions were generate a lot of corrosion. $US_7M_3$ solution was excellent in corrosion resistance, regardless of the steel type. The appearance of coating by $US_3M_3$ and $US_{11}M_3$ solutions were bumpy surface, and were a lot of fine defects. $US_7M_3$ solution was made a sophisticated molecular cross-linking structure inside the coating, it was a slick surface. Other characteristics are exhibited the excellent property for all solutions.

• Transactions of Materials Processing
• /
• v.24 no.6
• /
• pp.381-386
• /
• 2015

Recently, high-strength-steel sheets have been used extensively for increasing fuel-efficiency and stability in automobiles. A study on the characteristics regarding friction factors is required because high-strength-steel sheets have higher contact pressure at the tool interface as compared to low-strength steel sheets. For the current study, a sheet friction test was used to examine the influence of several factors on friction. The friction tests were performed on two types of sheet steels (SPFC590 and SPFC980) to obtain friction coefficients as a function of contact pressure, surface roughness, lubricant viscosity, and speed. Based on the experimental results for SPFC590 and SPFC980, the friction coefficient decreased with increasing contact pressure, but the friction coefficient increased with increasing surface roughness. Also, the friction coefficient decreased with increasing lubricant viscosity and decreasing speed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.5
• /
• pp.53-64
• /
• 2012

Deep and narrow welds can be produced by laser welding at high welding speeds with a narrow heat-affected zone (HAZ) and little distortion of the workpiece. This study aims to evaluate the usefulness of laser welding at automobile component manufacture. Microstructure observation, hardness test, tensile test and fatigue life test are performed by using the fiber laser welded SPFC590 steel sheets which is used widely in the manufacture of automotive seat frame. Three kinds of specimens are only a SPFC590 steel plate, quasi-butt joint plate and lap joint plate by laser welding. The following results that will be helpful to understand the static strength, fatigue crack initiation and growth mechanism were obtained. (1) The tensile strength of quasi butt joint specimens nearly equal to base metal specimens, but lap joint specimens fractured in shear area of weld metal. (2) The fatigue strength of quasi-butt joint specimen was approximately 8 percent lower than that of the base metal specimens. Furthermore, the lap joint specimens were less than 86 percent of the base metal specimens. (3) The lap joint fatigue specimens fractured at shear area in high level stress amplitude, while fractured at normal area in low level stress amplitude. From these results, the applicability of the laser welding to the automobile component is discussed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.8
• /
• pp.929-934
• /
• 2012

This study was carried out to analyze the dynamic characteristics of laser tailor-welded blanks (TWBs) made of dissimilar materials. The analysis was performed using Hyper Works 10.0 with Solver LS-DYNA v.971. 2D-Shell was used as the modeling element, and the number of elements and nodes was 35,641 and 36,561, respectively. The impact speed was 10 km/h. To analyze the impact characteristics according to the height of the weld line for the upper and lower parts of the center pillar, the length of the lower part was set as 300 and 400 mm. When the lower part was made of SPFC980 steel with a length of 300 mm, the deformation was the smallest and the absorbed energy of the impact force was the largest. On based the lower part of center pillar, the position of TWB shows the shorter and the better value. In other words, the performance depended on the proportion of the upper part made of high-strength SABC1470 steel. A lower part made of SPFH590 steel showed large deformation. In contrast, a lower part made of SPFC980 steel showed significantly lesser deformation. Therefore, the impact performance of a lower part made of SPFC980 steel with a length of 300 mm showed the best analysis result.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.794-801
• /
• 2021

This study examined the mechanical strength and corrosion resistance of a dissimilar joint with an aluminum alloy and steel by resistance element spot welding. SPFC980 steels and Al5052 alloys were applied as the base materials. S20C steels were assembled on Al5052 for the riveting element before the electric resistance welding process. The SPFC980-S20C riveted Al5052 was welded at a 6.5 kA current and 250 kgf/㎠. As a result, the engraved S20C elements formed unstable nuggets after the spot welding processes. In contrast, in the embossed S20C elements, exceptional mechanical properties, such as robust corrosion resistance and fatigue resistance, were obtained by structurally sound joints. The correlation between the microstructure and mechanical properties were examined by microstructural investigations and FEM simulations. The corrosion reliability of element spot-welded SPFC980-Al5052 dissimilar joints was investigated systematically.

• Journal of Power Electronics
• /
• v.1 no.2
• /
• pp.99-106
• /
• 2001

This paper describes the implementation of a Storage Power Flow Controller (SPFC) connected to the grid which can provide concomitant benefits associated with a Unified Power Flow Controller while at the same time providing several other very important benefits to power system operation such as, load leveling dynamic voltage stability inprovement, harmonic compensation and power factor correction. This Storage power Flow Controller (SPFC) was implemented using real time signal processors, three-phase inverter(s) and battery bank which can provide improved power system operation and control, added system security and reduced power system losses.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.8
• /
• pp.3644-3649
• /
• 2013

Automotive seat recliner has the function to control the angle at the back of chair and has the relation close to the safety of seat. Therefore each of parts constituting the recliner is important and the recliner housing to protect these parts from various dynamic loads is also important. In this study, the recliner housing with t=3mm which is made of high tension steel plate(SPFC 980) is applied to actual automotive seat. The deformation is investigated through the durability tester. Deformation and equivalent stress are also analyzed by simulation analysis under the same condition with experiment. After recliners with thicknesses of 1mm and 2mm are modeled by bases of experimental and analysis values, deformation and equivalent stress are investigated through structural analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.8
• /
• pp.997-1006
• /
• 2010

For manufacturing modern cars, so-called multi-materials, such as aluminum alloy with high-strength steels, are used. For obtaining such materials, a new joining method is required to achieve the multi-material design. Mechanical clinching is one of joining methods used to join the dissimilar materials. The objective of this study is to investigate the characteristics of mechanical clinching of Al5052 alloy to high-strength steels (SPFC440, 590, 780). Using FE-analysis and clinching experiment, the joinability of Al5052 alloy to high-strength steel is evaluated by geometrical shape of mechanical clinched joint, such as neck-thickness and undercut. Further, the joint strength is evaluated by performing a single-lap shear test. The upper high-strength steel SPFC780 was not clinched because of the necking of the upper sheet. The joint strength increased with increasing strength of the upper sheet. For the lower high-strength steel sheet, the joinability and joint strength decreased with increasing strength of the lower sheet.