• 청정기술
• /
• 제9권4호
• /
• pp.169-177
• /
• 2003

온도(0 to $30^{\circ}C$)와 압력(4 bar까지)의 함수로서 이온성액체인 buthylmethylimidazolium tetrafluoride ($BMIBF_4$)에 관한 디플루오로클로로메탄($CHCIF_2$, R22)과 헥사플루오로프로필렌($C_3F_6$, HFP) 가스의 용해도 실험을 실시하였는데, R227가스의 용해도는 온도가 낮거나, 압력이 증가할수록 거의 선형적으로 증가한 반면, HFP 가스는 거의 용해도를 나타내지 않았다. 이어서 이 이온성액체를 고분자지지체인 polyvinylidenefluoride(PVDF)에 함침량을 달리하여 액막을 제조하였으며, 일정한 압력(3 atm)에서 가스분리막 장치를 사용하여 액막의 이온성액체 함침량 변화와 조업온도의 함수로 R22, HFP 및 $N_2$ 가스의 투과특성 실험을 실시하였다. 실험결과, R22의 투과도는 주로 이온성액체의 함침량에 의존하여 급격히 증가하였으며, HFP 및 $N_2$의 투가도는 거의 0에 가까운 매우 낮은 값을 나타내었다. 또한 R22의 확산계수 및 용해도계수는 조업온도가 낮거나 액막에서 이온성액체의 함침량에 비례하여 증가하였다. 결과적으로 R22에 관한 HFP가스의 선택도는 조업온도와 액막의 이온성액체 함침량에 의존하여 10-45배 정도까지 매우 높은 값올 나타내었다.

• 한국환경보건학회지
• /
• 제38권4호
• /
• pp.351-359
• /
• 2012

Objectives: This study was conducted in order to investigate the specific correlation between physicochemical properties and bioactivity in ecdysteroids found in living organisms. Methods: The examined steroidal compounds were classified into three groups according to their relevance to ecdysone activity. Each compound molecule was completely drawn to automatically calculate its physicochemical parameters and docked against 20-hydroxyecdysone to calculate the total distance. Electronic charge distribution was also observed for each molecule. All procedures were conducted using a computational chemistry program. Results: Ecdysone agonists showed different ranges of parameter values, such as log P, hydrophilic-lipophilic balance (HLB), solubility parameter (SP), hydrophilic surface (HPS), hydrogen bond (HB) and Kappa 2, when compared with antagonists and steroids without ecdysone activity. They also showed a similar electronic charge distribution that is significantly different from the electron charge distribution of antagonists and steroids without ecdysone activity. The total distance values of agonists, estimated by docking them with 20-hydroxyecdysone, were relatively small but showed no correlation with binding affinity with receptor ligand. Conclusions: These results suggest that physicochemical properties such as steric and electronic effects, hydrophobicity and hydrogen bonding may operate in combination to determine the binding activity of ecdysteroids to the receptor protein.

• Elastomers and Composites
• /
• 제54권3호
• /
• pp.209-219
• /
• 2019

It is important to analyze crosslink densities of rubber articles because the physical properties are dependent on the crosslink densities. In this paper, analytical techniques for the measurement of crosslink densities of rubber vulcanizates are described. The most widely used method to measure the crosslink density is a swelling method combined with the Flory-Rehner equation. Application of the interaction parameter (${\chi}$) of rubber and swelling solvent is critical because the crosslink density is absolutely dependent on the ${\chi}$ value. Methods for obtaining ${\chi}$ employ not only solubility parameters of the polymer and swelling solvent but also inverse gas chromatography (IGC). The solubilities of rubbers can be obtained using micro differential scanning calorimetry (${\mu}DSC$), intrinsic viscosity measurement, and UV-visible spectroscopy. Nuclear magnetic resonance (NMR) spectroscopy has been also used for the measurement of the crosslink density using the $T_2$ relaxation time, which is determined by spin-spin relaxation in solid-state NMR. For sulfur-cured rubber vulcanizates, crosslink densities according to the crosslink types of mono-, di-, and polysulfides are measured by treating the rubber samples with a chemical probe composed of thiol and amine compounds. Measurement methods of physical crosslinking by filler, crystallization, and ionic bonding have also been introduced.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.189-194
• /
• 1999

The antiwear performance of several organic phosphates ,such as tricrecylphosphate(TCP), tributylphosphate(TBP), diphenylhydrogenphosphate(DPHP) ,dissolved in polyol ester based oils is studied. These organic phosphates are well known for antiwear additive for lubricating oil that produce reacted surface protective film. These antiwear additives can drastically reduce wear with their concentration increasing, because the amount of additive adsorbed on metal sur(ace increases. But in the higher concentration region, the wear is increased by excessive and corrosive reaction of the metal surface with these additives. That is to say, there is an optimum concentration for minimum wear. The optimum concentration was different with the kinds of base oils and additives. Different polyolesters showed different optimum concentrations of the additive. The order of optimum concentration among the polyolesters was different with different phosphates. The order of the optimum concentration is shown that the effect of the concentration of additives on the antiwear performance. It can be explained by the interaction between additives and base oils using the solubility parameter.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.471-476
• /
• 1994

The influence of TiO2 addition on the sintering and microstructure of magnesia ceramics was studied. An excess amount of TiO2 over the solid solubility limit reacted with magnesia to form Mg2TiO4 compound above 130$0^{\circ}C$. The deviation of lattice parameter of MgO was estimated to be under 0.2% when existence of TiO2 in MgO. The addition of TiO2 markedly promoted the densification of MgO at comparatively low temperature and the sintered density of about 98% of the theorectical was obtained at 150$0^{\circ}C$, 2h. The densification was mainly governed by grain growth of MgO and the effect of Mg2TiO4 existing as a second phase on depression of grain growth of MgO was not exhibited.

• Fibers and Polymers
• /
• 제4권4호
• /
• pp.204-209
• /
• 2003

The effect of padding solution on the microwave heat dyeing of polyester fabric was studied extensively. Polyester fabrics were impregnated in aqueous urea solution and aqueous sodium chloride solution for 10 min and then dyed for 7 min by microwave apparatus (2450 MHz, 700 W) under optimum conditions which provide good exhaustion. Aqueous solutions of urea and sodium chloride showed more effective than water as a padding solution for microwave heat dyeing. The type of solvent added in padding media and its concentration significantly affects the K/S values of dyed polyester fabric. Added solvents such as n-hexane, acetone, and dimethyl formamide were also more effective than 100 % water as padding media for the microwave heat dyeing. It is supposed that the effect of used solvents on dyeing property of polyester fabrics depends on the solubility parameter difference between solvent and polyester fabric.

• Korean Membrane Journal
• /
• 제1권1호
• /
• pp.73-80
• /
• 1999

The removal of trace chlorinated and aromatic hydrocarbons from water by a pervaporation technique has been carried out through poly (dimethylsiloxane) membrane which had been fabricated by the addition crosslinking reaction. This study dealt with the swelling and permeation behaviors of the PDMS membranes with dichloroethane trichloroethane and toluene aqueous solutions. The swelling ratio in the toluene aqueous solution was much higher than those in the chloroethane solutions at all of the operating temperatures and concentrations. The solubility parameter theory was introduced to interpret the affinity between permeates and a membrane material and in all cases this approach seemed to be proper. It was suggested that the existence of water clusters in the membrane due to the hydrophobic characteristics of the membrane made the size of the permeating water larger resulting in suppressing water permeation and increasing enrichment of the organic components. The permeation behaviors at different membrane thicknesses were indirectly interpreted in terms of the effect of concentration polarization.

• Elastomers and Composites
• /
• 제28권4호
• /
• pp.267-273
• /
• 1993

A number of hydrophilic acrylic comonomers were incorporated into styrene-butadiene soap-free emulsion polymerization. It was found that reaction rate decreased according to : AN>AA>MMA>EA>IA>AAM>MA>HEMA. It was also observed that reaction rate increased with decreasing H-bonding factor contribution to the solubility parameter of the hydrophilic comonoer. The SBR latexes were very monodisperse with the particle size distribution of $1.03{\times}1.12$. Since growth rate is proportional to polymerization time, the difference in conversion rates between various comonomers was resulted from the particle number density of SBR latexes for the various hydrophilic comonomers. It was also found that the colloidal stability of the latexes was excellent because no external emulsifier was incorporated.

• 한국안전학회지
• /
• 제5권3호
• /
• pp.63-68
• /
• 1990

The effects of various brominated flame retardants were investigated in PC/ABS blend system. The compatibilities between polymers and flame retardants were expected with the solubility parameter using group contribution theory. Tetrabromobisphenol A carbonate oligomer, among the flame retardants in this experiment, has been shown good miscibility for PC and ABS, respectively. But polydibromophenylene oxide and octabromodiphenyl oxide has immiscibility. The flame retardant PC/ABS blends containning tetrabromobisphenol A carbonate oligomer have been exhibited higher mechanical properties, tensile strengths and notch Izod impact strengths, at varlous content of flame retardants, than containning other flame retardants. It could be seen that the trends of mechanical properties for the flame retardant PC/ABS blends have a good concidence with the expectation of compatibility.

• 대한화학회지
• /
• 제18권4호
• /
• pp.272-277
• /
• 1974

분배계수와 용매의 용해도 파라미터 도표상의 추출포물선을 검토하여 질산산성에서 유로퓸을 TBP로 추출할 때 유로퓸착물과 TBP의 활동도 계수간의 관계를 알 수 있었고 이에 따라 TBP의 용해도 파라미터를 결정하는 가능성을 제시하였다. 용매로서는 cyclohexane, 벤젠, 톨루엔, chlorobenzene을 사용하였고 TBP의 농도를 용적백분율로 5에서 50까지 변화시켰다.