• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.509-515
• /
• 2005

Interfacial reactions at LSGM electrolyte and NiO-GDC anode interfaces were thoroughly investigated with Environmental Scanning Electron Microscopy (ESEM-PHlLIPS XL-30) and Energy Dispersive X-ray (EDX-Link XL30). According to the analysis, serious reaction zone was observed at LSGM/NiO-GDC interface. It was found that the reaction layer was originated from the chemical reaction between NiO and LSGM. The reaction products were identified as La deficient form of LSGM based perovskite and Ni-La-O compounds such as LaSrGa$_{3}$O$_{7}$ and LaNiO$_{3}$ from the X-Ray Diffraction (XRD, Philips) analysis. According to the electrical characterization, interfacial layer was very electrically resistive which would be the cause of high internal resistance and low power generating characteristic of the unit cell.

• New & Renewable Energy
• /
• v.3 no.3
• /
• pp.5-13
• /
• 2007

Stacks of solid oxide fuel cell with 1kW max power performance were designed on planar type employing anode-supported cells and metallic interconnects. The stacks composed of 3-cells, 8-cells, and 16-cells were fabricated and tested in serials by using anode-supported cells purchased from Indec, and sealants/interconnects prepared at RIST. In the performance test of the final 16-cells stack, OCV was recorded to be 16.7V. The peak power and the power density showed 1 kW, $0.77W/cm^2$ at $820^{\circ}C$, respectively. In addition, the long-term degradation rate of the power exhibited 2.25 % during 500h at $750^{\circ}C$.

• Journal of Powder Materials
• /
• v.20 no.6
• /
• pp.425-431
• /
• 2013

Microstructural and mechanical properties of Ni-YSZ fabricated using SPS processing have been investigated at various sintering temperatures. Our study shows samples to be applied as a SOFC anode have the proper porosity of 40% and high hardness when processed at $1100^{\circ}C$. These results are comparable to the values obtained at $100-200^{\circ}C$ higher sintering temperature reported by others. This result is important because when the fabrication processes are performed above $1100^{\circ}C$, the mechanical property starts to decrease drastically. This is caused by the fast grain coarsening at the higher temperature, which initiates a mismatch between thermal expansion coefficients of Ni and YSZ and induces cracks as well.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.1
• /
• pp.41-47
• /
• 2003

For the development of low temperature anode-supported planar solid oxide fuel cell, the planar anode supports with the thickness of 0.8 to 1 mm and the area of 25, 100 and $150\;cm^2$ were fabricated by the tape casting method. The strength, porosity, gas permeability and electrical conductivity of the planar anode support were measured. The porosity of anode supports sintered at $1400^{\circ}C$ and then reduced in$H_2$ atmosphere was increased from $45.8\%\;to\;53.9\%$. The electrical conductivity of the anode support was $900 S/cm\;at\; 850^{\circ}C$ and its gas permeability was 6l/min at 1 atm in air atmosphere. The electrolyte layer and cathode layer were fabricated by slurry dip coating method and then had examined the thickness of $10{\mu}m$ and the gas permeability of 2.5 ml/min at 3 atm in air atmosphere. As preliminary experiment, cathode multi-layered structure consists of LSM-YSZ/LSM/LSCF. At single cell test using the electrolyte layer with thickness of 20 to $30{\mu}m$, we achieved $300\;mA/cm^2$ and 0.6V at $750^{\circ}C$

• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.823-828
• /
• 2006

One of the main issues of Solid Oxide Fuel Cells (SOFCs) is to reduce the operating temperature to $750^{\circ}C$ or less. It has advantages of improving the life of component parts and the long-term stability of a system, so the production cost could be decreased. In order to achieve that, the ohmic and polarization loss of a single cell should be minimized first. This paper presents.to fabricate anode-supported single cells with controlling microstructure as a function of particle size and volume of graphite and NiO-YSZ weight ratio. By means of optimizing the manufactural condition through microstructure analysis and performance evaluation, the single cell which had NiO-YSZ=6:4, graphite volume of 24% and graphite size of $75{\mu}m$ as the anode composition showed a distinguished power density of $510mW/cm^2$ at $650^{\circ}C$ and $810mW/cm^2$ at $700^{\circ}C$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.768-774
• /
• 2006

The microstructure of Ni-YSZ cermets was controlled with fine and coarse starting powders (NiO and YSZ) to obtain a optimum strong and conductive tubular anode support for SOFCs. Three types of cermets with different microstructures, i.e., coarse Ni-fine YSZ, fine Ni-coarse YSZ, and fine Ni-fine YSZ, were fabricated to investigate their electrical and mechanical properties. The cermets from fine NiO powder showed high electrical conductivity due to the enhanced percolation of Ni particles. The cermet by foe Ni and coarse YSZ showed excellent electrical conductivity (>1000 S/cm) despite its high porosity $(\sim40%)$ but it showed poor mechanical strength due to the lack of percolation by YSZ particles and due to large pores. Thus fine NiO and YSZ powders were used to make strong and conductive Ni-YSZ support tube by extrusion. The microstructure of the anode tube was modified by the amount of polymeric additives and carbon black, a pore former. Ni-YSZ tube (porosity $\sim34%$) with the finer microstructure showed better performance both in electrical conductivity (>1000 S/cm) and fracture strength $(\sim140\;MPa)$. Either flat or circular NiO-YSZ tubes with the length from 20 to 40cm were successfully fabricated with the optimized composition of materials and polymeric additives.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.4
• /
• pp.257-268
• /
• 2017

This paper proposes an efficient two-dimensional simulation model for solid oxide fuel cells (SOFCs) based on the electrochemical effectiveness model. The effectiveness model is known to accurately predict the current generation performance of SOFC electrodes, by considering the complex reaction/transport processes that occur within thin active functional layers near the electrolyte. After validation tests, the two-dimensional simulation model was used to calculate the distribution of current density and oxygen concentration transverse to the flow channel in anode-supported SOFCs, with which the oxygen depletion characteristics were investigated in detail. In addition, simulations were also conducted to determine the minimum number of grids required in the transverse direction to efficiently obtain accurate results.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.3
• /
• pp.31-35
• /
• 2016

This paper demonstrates the successful application of yttria-stabilized zirconia thin films deposited by atomic layer deposition to the anode-side interlayer for cerium oxide electrolyte based solid oxide fuel cell. At the operating temperature over $500^{\circ}C$, the electrical conductivity of cerium oxide electrolyte is known to dramatically increase and, therefore, the open circuit voltage of the cell decreases leading to the decrease of the performance. Ultra-thin (60 nm) atomic layer deposited yttria-stabilized zirconia thin film in this study conformally coated the anode-side surface of the cerium oxide electrolyte and efficiently blocked the electrical conduction through the electrolyte. Accordingly, the open circuit voltage increased by up to 20%, and the maximum power density increased by 52% at $500^{\circ}C$

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.76-76
• /
• 2003

제 3세대로 불리우는 차세대 발전시스템인 고체산화물 연료전지(Solid Oxide Fuel Cell, SOFC)는 연료전지 가운데 발전효율이 가장 높고, NOx와 SOx의 발생이 없는 무공해 청정에너지 발전 시스템으로 많은 연구가 진행되고 있다. 이중 원통형 구조는 전력밀도가 평판형 구조에 비해 다소 떨어지나 반응기체의 밀봉이 쉽고, 기계적 강도가 높으며, 열응력에 대한 저항성이 높아 스텍제작이 비교적 용이하며 장기 운전이 가능하다는 장점이 있으며, 평판형 구조의 경우는 전류의 흐름이 구성요소의 면에 수직방향으로 흐르므로 전력밀도가 높은 장점이 있으나 가스의 밀봉이 어렵고, 기계적 강도나 열응력에 대한 저항성이 높은 단점을 갖고 있다. 본 연구에서는 원통형 구조와 평판형 구조의 상호 장점을 보완하여 기존의 원통형의 구조를 최적화하여 개선한 연료극 지지체식 Flat-Tube형 고체산화물 연료전지의 제조와 특성에 대한 연구를 발표하고자 한다.

• Journal of the Korean Ceramic Society
• /
• v.45 no.12
• /
• pp.788-795
• /
• 2008

An electrolyte supported SOFC cell was tested at $800^{\circ}C$ in air for 3600 h with an applied current density of $200\;mA/cm^2$ to examine possible cathode degradation issues. A scandium- stabilized zirconia (ScSZ) with additional manganese doping (ScSZ: Mn) was used as electrolyte. A strontium and copper-doped lanthanum ferrite (LaSrCuFe) and platinum were used as cathode and quasi-anode material, respectively. The DC resistance was logged over the complete testing period. Additionally, impedance spectroscopy was used from time to time to track changes of the cell in-situ. Post-test analysis of the cell using methods like scanning electron microscopy imaging and other electrochemical testing methods allow the identification of different degradation sources. The results indicate a promising combination of electrolyte and cathode material in terms of chemical compatibility and electrical performance.