• 한국멀티미디어학회논문지
• /
• 제19권2호
• /
• pp.360-374
• /
• 2016

Since WSNs (Wireless Sensor Networks) applied to their application areas such as smart home, smart factory, environment monitoring, etc., depend on sensor data, the sensor data is the most important among WSN components. The resources of each node consisting of WSN are extremely limited in energy, hardware and so on. Due to these limitation, communication failure probabilities become much higher and the communication failure causes data loss to occur. For this reason, this paper proposes 2MC (Maximum/Minimum Compression) that is a method to compress sensor data by selecting circular queue-based maximum/minimum sensor data values. Our proposed method reduces sensor data losses and value errors when they are recovered. Experimental results of 2MC method show the maximum/minimum 35% reduction efficiency in average sensor data accumulation error rate after the 3 times compression, comparing with CQP (Circular Queue Compression based on Period) after the compressed data recovering.

• 복식
• /
• 제26권
• /
• pp.251-264
• /
• 1995

The purpose of this study is to introduce and research the traditional Korean costume collections of Dr. McCune who was born in Pyung-Yang in 1907 and resided until her marriage to George S. McCune in about 1930. Her collections consist of three categories : children's costumes, adults' costumes, access-ories. The characteristics of collections are summorized as follows : 1. Deep wrappings are found at the front part of the top clothing when worn. The front gusset (SUB) has been dramaticaly tilted due to the difference in lengths of the top and bottom parts of the front gusset. 2. Assymetry was one of the principles of decorating Korean costumes. The assymetry were repeated at the GIT and SUB of CHOGORE with patchwork patterns. 3. Primary colors were favored in Korean costume. Hue contrast in color combinations was prefered as well, such as : yellow CHOGORE and purple blue CUFFS, a red SUN pattern matched with green embroidery. 4. Surface patterns were not so popular in Korean costumes, while the most colorful and fabulous patterns were shown through the various embroidery artifacts. Patterns were used as a way of expressing of their desires or longings in Korean costumes. The main themes of the patterns were longevity and happiness. The patterns such as peony, lotus, chrysanthemum, bamboo and bat were implying symbolism at that time. 5. Natural materials were prefered for the garments, Silk and cotton were used as the main materials of the costume collections. Studies of Korean Costume collections owned by international collectors are meaningful to boost the arena of Korean Costumes as well as fill up the vacancy left by lost costume artifacts.

• 한국정보처리학회논문지
• /
• 제5권1호
• /
• pp.137-148
• /
• 1998

본 논문에서는 현대 데이터 컨퍼런싱 분야에서 국제적인 표준으로 되어있는 T.120시리즈의 핵심 기술인 MCS를 멀티캐스트 수송계층 포르토콜 위에서 수행하기 위한 알고리듬을 제안하고 이에 따른 구현 구조를 기술하였다. 구현된 알고리즘은 기존의 MCS와 역방향 호환성을 유지하면서 새로운 멀티캐스트 수송계층의 기능을 충분히 이용할 수 있게 하였다. 이를 위하여 MCS의 연결설정 시에 상대의 수송계층이 멀티캐스트 기능을 가지고 있는 지를 조사하여 멀티캐스트 기능이 있다면 멀티캐스트 수송계층의 기능을 이용하고, 없다면 단일 수송계층을 이용하게 된다. 이러한 기술적인 내용에 대하여는 T.120 시리즈의 상호운용성 시험을 주관하는 IMTC에 기고될 예정이다.

• Geomechanics and Engineering
• /
• 제9권1호
• /
• pp.115-124
• /
• 2015

Determination of mobilized shear strength parameters (that identify stresses on the failure plane) is required for analyzing the stability by limit equilibrium method. Generalized Hoek-Brown (GHB) and Mohr-Coulomb (MC) failure criteria are usually used for obtaining stresses on the plane of failure. In the present paper, the applicability of these criteria for determining the stresses on failure plane is investigated. The comparison is based on stresses on the real failure plane which are obtained from the Mohr stress circle. To do so, 18 sets of data (consist of principal stresses and angle of failure plane) presented in the literature are used. In addition, the values account for (VAF) and the root mean square error (RMSE) indices were calculated to check the determination performance of the obtained results. Values of VAF and RMSE for the normal stresses on the failure plane evaluated from MC are 49% and 31.5 where for GHB are 55% and 30.5, respectively. Also, for the shear stresses on failure plane, they are 74% and 36 for MC, 76% and 34.5 for GHB. Results show that the obtained stresses and angles of failure plane for each criterion differ from real ones, but GHB results are closer to the empirical results. Also, it is inferred that results are affected by the failure envelope not real failure plane. Therefore, obtained shear strength parameters are not mobilized. Finally, a multivariable regressed relation is presented for determining the stresses on the failure plane.

• 한국지반환경공학회 논문집
• /
• 제11권12호
• /
• pp.37-45
• /
• 2010

초미립자시멘트는 입자 크기가 마이크로화되어 실트성 지반까지 주입가능하지만 점성이 높아 침투성이 저하되는 단점이 있다. 본 연구에서는 유동화제를 사용하여 점성을 낮춘 초미립자주입재의 그라우팅 효과를 평가하고자 암반에서 초미립자주입재와 보통시멘트주입재의 주입효과를 비교하였다. 시추조사, 현장수압시험, 공내재하시험, 공내전단시험, 단위주입량분석, p~q~t chart 유형 분석을 실시하였다. 시험 결과 초미립자주입재를 사용하는 경우가 보통시멘트 주입재를 사용하는 경우보다 투수성, 탄성계수 및 변형계수, 단위주입량 및 주입재 회수율 등 측면에서는 유리하지만 전단응력 측면에서는 차이가 거의 없는 것으로 나타났다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 A
• /
• pp.476-478
• /
• 1993

Instead of installing new communication wiring to each house in the apartment house building. the power distribution network. which is already installed in the building. can be use as communication medium. In a safty management, by adoption of power line communication system, at remote we can monitor safty related sensors such as fire, gas leakage, burglar intrusion and emergency call which are located at each house. From this viewpoint, we developed security monitoring system for apartment house building using power lines. Security monitoring system consists of Power Line Communication-Sub Controller (PLC-SC). Power Line Communication-Main Controller (PLC-MC) and Management System (MS). Between a PLC-MC and a PLC-SC, the transmission rate is 1200 bps in power lines and modulation technique is frequency shirt keying (FSK). In between a PLC-MC and a MS, the transmission rate is 1200 bps in communication line (RS-485). As a result of this research. transmission loss is 0.1dB per meter of intrabuilding distribution network. Transmission can be reach in 250 meters. So it is enough to communicate for security monitoring system in apartment house building.

• Nuclear Engineering and Technology
• /
• 제54권1호
• /
• pp.30-35
• /
• 2022

In a nuclear reactor, gamma radiation is the dominant energy deposition in non-fuel regions. Heat is generated upon gamma deposition and consequently affects the mechanical and thermal structure of the material. Therefore, the safety of samples should be carefully considered so that their integrity and quality can be retained. To evaluate relevant parameters, an in-core gamma thermometer (GT) was used to measure gamma heating (GH) throughout the operation of the McMaster nuclear reactor (MNR) at four irradiation sites. Additionally, a Monte Carlo reactor physics code (Serpent-2) was utilized to model the MNR with the GT located in the same irradiation sites used in the measurement to verify its predictions against measured GH. This research aids in the development of modeling, calculation, and prediction of the GH utilizing Serpent-2 as well as implementing a new GH measurement at the MNR core. After all uncertainties were quantified for both approaches, comparable GH profiles were observed between the measurements and calculations. In addition, the GH values found in the four sites represent a strong level of radiation based on the distance of the sample from the core. In this study, the maximum and minimum GH values were found at 0.32 ± 0.05 W/g and 0.15 ± 0.02 W/g, respectively, corresponding to 320 Sv/s and 150 Sv/s. These values are crucial to be considered whenever sample is planned to be irradiated inside the MNR core.

• 대한한방내과학회지
• /
• 제36권4호
• /
• pp.518-526
• /
• 2015

Objectives This study investigated the effect of purified safflower (Carthamus tinctorius Linne) and safflower seed (Carthamus tinctorius L. seed; CS) extract, using hot water and ethanol extract methods , on the osteogenic differentiation of MC3T3E1 cells.Methods The safflower and safflower seed were extracted with hot water and ethanol. The samples were concentrated by a rotary evaporator and then freeze-dried using a freeze-dryer. The MC3T3E1 cells were propagated and maintained in DMEM (Gibco) containing 10% FBS and a 1% antibiotic antimycotic solution. To induce osteogenic differentiation, the cells were treated for 14 days with DMEM with 10 mM β-glycerophosphate and 50 μM ascorbic acid. Extract doses were confirmed by the results of an MTT assay, and treatment of the extracts was performed in a differentiation medium every two days. The ALP staining and activity were tested after osteogenic differentiation for five days, and after 14 days, osteogenic differentiation was determined by alizarin red S staining. The mRNA expressions of osteogenic-related genes were quantified using quantitative real-time PCR.Results In the results of the MTT assay, all concentrations of safflower extracts had no toxicity in the MC3T3El cells. But in the groups of 100 ng/ml and 200 ng/ml concentrations of safflower seed extracts, the cell viability was significantly reduced by up to 40-50%. So we fixed the treatment concentration of the extract at 50 ng/ml. In the ALP and alizarin red S staining, all extract groups increased osteogenic differentiation compared with the control group. The water-safflower extract group showed the highest mRNA level of Alp, Runx2, and Dlx5 genes. The mRNA level of Ocn, an osteogenic gene related to late-stage differentiation, in the ethanol-safflower extract group increased the mineralization more significantly than in other groups.Conclusions These data suggest that the extract of safflower increases the osteoblastic differentiation activates of MC3T3E1 cells like the extract of safflower seed. The water-extract and ethanol-extract of safflower have effects on different stages of osteogenesis in MC3T3El. Not only safflower seed but also safflower will be useful therapeutic reagents for age-associated chronic diseases such as osteoporosis.

• 국제학술발표논문집
• /
• The 9th International Conference on Construction Engineering and Project Management
• /
• pp.319-327
• /
• 2022

Robots for construction sites, although not deeply widespread, are finding applications in the duties of project monitoring, material movement, documentation, security, and simple repetitive construction-related tasks. A significant shortcoming in the use of robots is the complexity involved in programming and re-programming an automation routine. Robotic programming is not an expected skill set of the traditional construction industry professional. Therefore, this research seeks to deliver a low-cost approach toward re-programming that does not involve a programmer's skill set. The researchers in this study examined an approach toward programming a terrestrial-based drone so that it follows a taped path. By doing so, if an alternative path is required, programmers would not be needed to re-program any part of the automated routine. Changing the path of the drone simply requires removing the tape and placing a different path - ideally simplifying the process and quickly allowing practitioners to implement a new automated routine. Python programming scripts were used with a DJI Robomaster EP Core drone, and a terrain navigation assessment was conducted. The study examined the pass/fail rates for a series of trial run over different terrains. The analysis of this data along with video recording for each trial run allowed the researchers to conclude that the accuracy of the tape follow technique was predictable on each of the terrain surfaces. The accuracy and predictability inform a non-coding construction practitioner of the optimal placement of the taped path. This paper further presents limitations and suggestions for some possible extended research options for this study.

• Coupled systems mechanics
• /
• 제2권4호
• /
• pp.329-348
• /
• 2013

This study aims at observing the coupling behaviours between suspended ceilings and partition walls in terms of their global seismic performance using full-scale shake table tests. The suspended ceilings with planar dimensions of $6.0m{\times}3.6m$ were tested with two types of panels: acoustic lay-in and metal clip-on panels. They were further categorized as seismic-braced, seismic-unbraced, and non-seismic installations. Also, two configurations of 2.7 m high partition wall specimens, with C-shape and I-shape in the plane layouts, were tested. In total, seven ceiling-partition-coupling (CPC) specimens were tested utilizing a unidirectional seismic simulator. The test results indicate that the damage patterns of the tested CPC systems included failure of the ceiling grids, shearing-off of the wall top railing, and, most destructively, numerous partial detachments and falling of the ceiling panels. The loss of panels was mostly concentrated near the center of the tested partition wall. The testing results also confirmed that the failure mode of the non-seismic CPC systems was brittle: The whole system would collapse suddenly all at once when the magnitude of the inputs hit the capacity threshold, rather than displaying progressive damage. Overall, the seismic capacity of the unbraced and braced CPC systems could be up to 1.23 g and 2.67 g, respectively; these accelerations were both achieved at the base of the partition wall. Nonetheless, for practical applications, it is noteworthy that the three-dimensional nature of seismic excitations and the size effect of the ceiling area are parameters that exacerbate the CPC's seismic response so that their actual capacity may be dramatically decreased, leading to important losses even in moderate seismic events.