• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.5
• /
• pp.515-525
• /
• 2014

In this paper, we present a design and implementation of a Voltage-tuned Planar Composite Resonator Oscillator(Vt-PCRO) with a low phase noise. The designed Vt-PCRO is composed of a resonator, two phase shifters, and an amplifier. The resonator is designed using a dual mode SIW(Substrate Integrated Waveguide) resonator and has a group delay of about 40 nsec. Of the two phase shifters (PS1 and PS2), PS1 with a phase shift of $360^{\circ}$ is used for the open loop gain to satisfy oscillation condition without regard to the electrical lengths of the employed microstrip lines in the loop. PS2 with a phase shift of about $70^{\circ}$ is used to tune oscillation frequency. The amplifier is constructed using two stages to compensate for the loss of the open loop. Through the measurement of the open loop gain, the tune voltage of the PS1 can be set to satisfy the oscillation condition and the loop is then closed to form the oscillator. The oscillator with a oscillation frequency of 5.345 GHz shows a phase noise of -130.5 dBc/Hz at 100 kHz frequency offset. The oscillation power and the electrical frequency tuning range is about 3.5 dBm and about 4.2 MHz for a tuning voltage of 0~10 V, respectively.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.171-174
• /
• 2010

In the paper, a printed dual-dipole array antenna is presented. A 4-way planar SIW power divider is adopted for feeding the array antenna. The dual-dipole is adopted as radiation elements which greatly improves the impedance band. The measured bandwidth larger than 31 % for VSWR$\leq$1.5 operating near 14 GHz is achieved and in agreement with the simulated results. The radiation E-plane and H-plane radiation pattern is presented in the paper. The radiation gain is also presented in the paper.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.175-178
• /
• 2010

In this paper, a millimeter-wave multi-beam antenna is studied by rotating the antipodal linear tapered slot antenna(ALTSA) with respect to a center is successfully designed. In order to lowering the SLL and enhancing the isolation between the ALTSA elements, a row of metallic via is inserted between the ALTSAs. A 9 beams antenna is designed and experimented at Ka band. The measured and simulated results agree well with each other. The antenna can provide horizontal wide angle coverage up to ${\pm}62^{\circ}$. The gain of each beam can achieve about 12.5 dB. The mutual coupling between ports is all below 20 dB.

• ETRI Journal
• /
• v.36 no.6
• /
• pp.1062-1065
• /
• 2014

A novel substrate-integrated waveguide (SIW) cavity-backed slot antenna is proposed in this study to achieve enhanced-gain performance. The peak gain is remarkably improved with the use of an SIW cavity and metallic superstrate. The superstrate comprises a single rectangular slot window and two half-wavelength patches. The gain can be enhanced by combining the in-phase radiating fields. Further, the 10 dB bandwidth of the proposed antenna ranges from 2.32 GHz to 2.49 GHz, which covers the wireless local area network band. The measured peak gain is 9.44 dBi at 2.42 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.680-687
• /
• 2009

In this paper, we propose a substrate integrated waveguide(SIW) power divider to yield excellent broadband isolation performance. In order to achieve high broadband isolation, a two stage Wilkinson power divider is employed in SIW. The measurement results show the insertion loss($S_{21}$, $S_{31}$ to be $4.0{\pm}0.5$ dB) and input return loss($S_{11}$ of 10 dB) from 13.12 GHz to 16.14 GHz. Moreover, the results show that the output return loss and isolation between output ports are larger than 10 dB between 10.37 GHz and 17.64 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.4
• /
• pp.470-480
• /
• 2011

Analog ferrite phase shifters based on rectangular waveguides which are used as component of passive phased array system have high power handling capability, but it is heavy and has high cost to fabricate. In this paper, we propose an analog ferrite phase shifter using substrate integrated waveguide(SIW), which has low cost and is easy to fabricate because it uses printed circuit board(PCB) process. The proposed structure is fabricated by using centeral dielectric material removal for inserting a ferrite bar. The measured results show that the proposed structure has not only $5.1^{\circ}$/mm phase variation but also return loss variation under 12.9 dB. Therefore, it is expected that the proposed phase shifter can plays an role to reduce weight and to has low cost on the phased array system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.11
• /
• pp.1584-1589
• /
• 2013

A new and significantly small guided and resonant structure is suggested to take over bulky metallic hollow waveguides used in military satellite transceivers. Below Ku-band, the conventional waveguides resulting in quite heavy transceivers will be replaced by the low profile SIW(substrate integrated waveguide) structures that are distinguished from the others in that the suggested ones have much lower cut-off frequencies by the circuital configuration of DNG(dobule negative) constitutive parameters and become even smaller than the other SIWs. The design scheme is validated by the circuit and full-wave simulations from the guided, resonant, and coupled structures. Besides, a bandpass filter as the suggested coupled structure is fabricated with a cheap substrate in a low-budget fabrication process and its frequency response is measured as verification of the purpose of the design.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.179-182
• /
• 2010

This paper proposed a novel compact bandpass filter with folded half mode substrate integrated waveguide (FHMSIW) cavities using two-layer printed circuit board(PCB) process. The area of the FHMSIW filter is reduced by nearly 50 % and 75 % compared with half mode substrate integrated waveguide(HMSIW) filter and substrate integrated waveguide(SIW) filter, respectively. A four-pole Chebyshev FHMSIW bandpass filter at C-band has been designed, simulated and fabricated. Measured results are presented and found to agree with the full-wave simulated results by using Ansoft HFSS. The filter shows good performance and compact size.

• ETRI Journal
• /
• v.45 no.2
• /
• pp.338-345
• /
• 2023

A filtering power divider based on air-filled substrate-integrated waveguide (AFSIW) technology is proposed in this study. The AFSIW structure is used in the proposed filtering power divider for substantially reducing the transmission losses. This structure occupies a large area because of the use of air as a dielectric instead of typical dielectric materials. A filtering power divider provides power division and frequency selectivity simultaneously in a single device. The proposed filtering power divider comprises three AFSIW cavities. The filtering function is achieved using symmetrical inductive posts. The input and output ports of the proposed circuit are realized by directly connecting coaxial lines to the AFSIW cavities. This transition from the coaxial line to the AFSIW cavity eliminates the additional transitions, such as AFSIW-SIW and SIW-conductor-backed coplanar waveguide, applied in existing AFSIW circuits. The proposed power divider with a second-order bandpass filtering response is fabricated and measured at 5.5 GHz. The measurement results show that this circuit has a minimum insertion loss of 1 dB, 3-dB fractional bandwidth of 11.2%, and return loss exceeding 11 dB.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.4
• /
• pp.29-34
• /
• 2023

A clear and efficient design method for a microstrip-to-waveguide inline transition, which is based on an analytical model, is presented. The transition consists of three parts: a microstrip-to-SIW transition, a dielectric-loaded waveguide with substrate-height, and a stepped-height waveguide. The shape of the transitional structure is formed for impedance matching. Two equivalent type0s of dielectric-loaded transitional structures are proposed. The design method is applicable to any size of the waveguide, but a design method of two Ka-band transitions is demonstrated. The proposed transitions, in a back-to-back configuration, have less than 1.2 dB insertion loss and more than 15 dB return loss from 29.8 GHz to 38.2 GHz.