• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.5
• /
• pp.435-441
• /
• 2010

To verify the possibility of a power generation system using biogas from the waste of pig farm for rural electric production, a SI gasoline engine is modified to use biogas fuel and was installed in a 20 KVA power generation system. An electronic speed regulation unit is developed to keep the system speed at 1500 rpm. Experimental investigations have been carried out to examine the performance characteristics of power generation system (such as: system frequency, phase output voltage,$\ldots$). In addition, the operating parameters and output emissions ($NO_x$, HC, and $CO_2$) of biogas-fueled engine are preliminary evaluated and analyzed for the change of system load. Results indicated that the researched power generation system shows a high stability of output voltage and frequency with help of speed regulator. Biogas fuel (mainly $CH_4$ and $CO_2$) has an environmental impact and potential as a green alternative fuel for SI engine and they would not require significant modification of existing engine hardware. Output emissions of biogas-fueled engine are found to be relative low. $NO_x$ emission increases with the increase of output electric power of the power generation system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.5 s.248
• /
• pp.405-412
• /
• 2006

In order to realize a stably propagating flame in a narrow channel, flame instabilities resulting from flame-wall interaction should be avoided. In particular flame quenching is a significant issue in micro combustion devices; quenching is caused either by excessive heat loss or by active radical adsorptions at the wall. In this paper, the relative significance of thermal and chemical effects on flame quenching is examined by means of quenching distance measurement. Emphasis is placed on the effects of surface defect density on flame quenching. To investigate chemical quenching phenomenon, thermally grown silicon oxide plates with well-defined defect distribution were prepared. ion implantation technique was used to control defect density, i.e. the number of oxygen vacancies. It has been found that when the surface temperature is under $300^{\circ}C$, the quenching distance is decreased on account of reduced heat loss; as the surface temperature is increased over $300^{\circ}C$, however, quenching distance is increased despite reduced heat loss effect. Such abberant behavior is caused by heterogeneous surface reactions between active radicals and surface defects. The higher defect density, the larger quenching distance. This result means that chemical quenching is governed by radical adsorption that can be parameterized by oxygen vacancy density on the surface.

• Proceedings of the Korean Environmental Health Society Conference
• /
• 2004.06a
• /
• pp.142-145
• /
• 2004

The purpose of this study was to characterize background mass concentration of fine particle PM10 and metallic composition from September 2001 to August 2002 in comparison with a medium-sized city, Asan and a metropolitan city, Seoul. Annual mean PM10 concentrations in Asan and Seoul were 47.98 and $75.33\;{\mu}g\;/\;m^3$, respectively. The concentrations of PM10 were highest in spring season in both cities. The concentrations of measured metals except As and Pb in Asan were higher than those in Seoul. Yellow dust could affect the mass and metals concentrations of measured PM10 in Asan and Seoul. Relationship between measured metals concentrations showed that Si and Fe were associated with natural sources such as soil. Pb, Cu and Zn were closely related to urban anthropogenic sources such as fuel combustion. Especially, relationship between metals showed different association during yellow dust. Proper management for fine particles is warranted in Asan, considering the concentrations of metallic elements in fine particles in Asan were relatively higher than those in Seoul.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.6
• /
• pp.575-584
• /
• 2001

Erosion due to abrasive particles contained in gas streams from boilers has been emerged as a significant problem in the coal fired power plants. Particle erosion accounted for approximately 50% of boiler failures and especially flyash erosion was responsible for 20~30% of emergency boiler shutdowns. Particularly, because of the high ash loading and high velocity, most erosion occurs in the boiler tubes and economiser tube bank where the direction of the gas stream changes to $180^{\circ}$ .In this study, a high temperature particle erosion tester was used to evaluate erosion rate in a simulated environment. The erosion parameters such as erosion temperature, particle impact angle, particle velocity and various particle size were changed. Flyash is the combustion product of the pulverized coal, where size is ranging from 1 to $200\mu\textrm{m}$. Flyash composed of mainly SiO$_2$, $A1_2$$_O3$, and $Fe_2$$O_3$has dense spherical particles and irregular particles containing numerous pores and cavities. From the erosion tests at various conditions, the maximum erosion was experienced at impact angles of $30^{\circ}$ to $60^{\circ}$ In addition, erosion rate increased in proportional to velocity and temperature. And from the observation of the eroded surfaces, it was also concluded that 304 stainless steel was mainly eroded by extrusion-forging at high impact angle ($90^{\circ}$) and by microcutting mechanism at low impact angles ($30^{\circ}$ and $45^{\circ}$).

• Journal of Energy Engineering
• /
• v.11 no.3
• /
• pp.224-229
• /
• 2002

During the operation of Circulating Fluidized Bed Combustion Boiler, defluidization is mainly caused by the formation of clinker. The clinker is made of components of Si, Fe, Ca, etc. However, although the defluidization is widely researched, the major factor has not been validated yet clearly. In this study, in the view of the shape and the arrangement of nozzles at a distributor (type 1, type 2), the formation of clinker is examined by CFD calculations and an improved nozzle design is proposed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.361-365
• /
• 2005

Since the fuel cell uses the hydrogen for its fuel. it has no emission and higher efficiency than an internal combustion engine. Also fuel cell is much quieter than engine generator and generates heat much less than engine generator. So it has advantage of Army's 'si lent watch' capability and the ability to operate undetected by the enemy. The fuel cell hybrid system combines a fuel cell power system with an ESS. The ESS (e.g., batteries or ultracapacitors) reduces the fuel cell's peak power and transient response requirements. It allows the fuel cell to operate more efficiently and recovery of vehicle energy during deceleration. The battery has high energy density, so it has the advantage regarding driving distance. However, it has a disadvantage considering dynamic characteristic because of low power density. One other hand. the ultracapacitor has higher power density, so it can handle sudden change or discharge of required power. Yet. it has lower energy density. so it will be bigger and heavier than the battery when it has the same energy. This paper proposes the power management strategy for multi-power source fuel cell hybrid system. which is applied with the merits of both battery and ultra capacitor by using both of them simultaneous.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.223-227
• /
• 2005

A PCV valve is a part to control the flow rate of Blowby gas in a PCV system. A PCV system re-burns Blowby gas with fuel in a combustion chamber. Some gas enters to a crankcase room through the gap between piston ring and engine cylinder wall. This gas si called 'Blowby gas'. This gas causes many problems. In environmental view, Blowby gas includes about $25\~35\%$ hydrocarbon{HC) of total generated HC in an automobile. Hydrocarbon is a very harmful pollutant element in our life. In mechanical view, Blowby gas has some reaction with lubricant oil of crankcase room. Then, this causes lubricant oil contamination, crankcase corrosion and a decrease fo engine efficiency. Consequently, Blowby gas must be eliminated from a crankcase room. In this study, we simulated internal flow characteristics in a PCV valve according to spool dynamic behavior using local remeshing method And, we programmed our sub routine to simulate a spool dynamic motion. As results, spool dynamic behavior is periodically oscillated by the relationship between fluid force and elastic force of spring. And its magnitude is linearly increased by the differential pressure between inlet and outlet. Also, as spool is largely moved, flow area is suddenly decreased at orifice. For this reason, flow velocity is rapidly decreased by viscous effect.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.2
• /
• pp.66-68
• /
• 2014

Most commercial white LED lamps use blue chip coated with yellow emitting phosphor. The use of blue excitable red and green phosphors is expected to improve the CRI. Several phosphors, such as $SrGa_2S_4:Eu^{2+}$ and $(Sr,Ba)SiO_4:Eu^{2+}$, have been suggested in the past as green components. However, there are issues of the sensitivity and stability of such phosphors. Here, we describe gallium substituted $YAG:Ce^{3+}$ phosphor, as a green emitter. YAG structures are already accepted by the industry, for their stability and efficiency. LEDs with improved CRI could be fabricated by choosing $Y_3Al_4GaO_{12}:Ce^{3+}$ (green and yellow), and $SrS:Eu^{2+}$ (red) phosphors, along with blue chip. Also, the effect of a slight change in chip wavelength is studied, for two phosphor-coated w-LEDs. The reduction in particle size of the coated phosphors also gives improved w-LED characteristics.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.97-100
• /
• 2006

Accelerating ability is one of the most important performance of the vehicle. Unlike conventional internal combustion vehicles and power-assist hybrid vehicles, the maximized acceleration of dual mode hybrid vehicles is not simply. achieved by maximizing engine or motor torque Because of the dynamic stability of planetary gear, speeds and torques control of engine, motor 1 and motor 2 is essential and according to control value, acceleration performance is changed There are two control values which are velocity and torque for each component totalling six. These six values can be variables for an objective function. However, because three velocity variables can be regarded as only one variable speed ratio and the remaining three torque variables can be solved analytically, without complicated numerical algorithm the solution for the objective function can be obtained. This optimized solution shows the best performance possible to the specified dual mode system.

• 한국연소학회:학술대회논문집
• /
• 2000.12a
• /
• pp.217-228
• /
• 2000

Circulating Fluidized Bed Combustor(CFBC) has been used for the incineration of waste sewage sludge and for the power generation. In this study hydrodynamic characteristics of two phase flow have been studied in a riser section of CFBC. A lab-scale riser is designed and SiC (Geldart type B) is used for solid particles. Experiments are performed by controlling the fluidization parameters including superficial velocity and secondary air to primary air ratio for determination of solid holdup profiles in the riser. Superficial velocities of each fluidization regime are well agreed with results predicted by a theoretical model. The results show that the axial solid holdup distributions calculated by measuring differential static pressures in the riser are found to show a basic profile described by a simple exponential function. Our flow regime during experiments mainly belongs to fast fluidization regime for particle size of 300${\mu}m$. As the SA/PA ratio increases, solid holdup in the lower dense region of the riser increases.