• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.575-580
• /
• 2014

We uniformly coated Eu(III)- and Tb(III)-doped yttrium oxide onto the surface of $SiO_2$ spheres and then characterized them by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction crystallography and UV-Visible absorption. 2D and 3D photoluminescence image map profiles were reported for the core-shell type structure. Red emission peaks of Eu(III) were observed between 580 to 730 nm and assigned to $^5D_0{\rightarrow}^7F_J$ (J = 0 - 4) transitions. The green emission peaks of Tb(III) between 450 and 650 nm were attributed to the $^5D_4{\rightarrow}^7F_J$ (J = 6, 5, 4, 3) transitions. For annealed samples, Eu(III) ions were embedded at a $C_2$ symmetry site in $Y_2O_3$, which was accompanied by an increase in luminescence intensity and redness, while Tb(III) was changed to Tb(IV), which resulted in no green emission.

• Corrosion Science and Technology
• /
• v.12 no.4
• /
• pp.185-190
• /
• 2013

In the present study, $Ni-TiO_2$ composite coatings were electrodeposited in a sulfamate bath containing $TiO_2$ particles. The influence of the ultrasonic treatment on the co-deposition of $TiO_2$ particles in the coating and the hardness of the electrodeposited $Ni-TiO_2$ composite has been investigated. Three different ultrasonic treatments (pretreatment before the electrodeposition (pre-UT), pretreatment + applied during the electrodeposition (UT), and the electrodeposition without the ultrasonic treatment (w/o UT)) were performed. The $Ni-TiO_2$ composite coatings are characterized using scanning electron microscopy (SEM), image analyzer, and hardness tester. Comparison of results indicates that the volume fraction is more important factor than the agglomerated particle size in terms of the strength improvement, and the strength of the electrodeposited $Ni-TiO_2$ composite coatings is enhanced with pre-UT condition.

• Corrosion Science and Technology
• /
• v.17 no.1
• /
• pp.30-36
• /
• 2018

The high rate of corrosion of magnesium alloys makes it limited for industrial applications. Therefore, surface treatment is required to enhance their corrosion resistance. In our study, a chemical conversion coating for protecting the corrosion of the magnesium alloy, AZ31B, was prepared by using a phosphate-permanganate solution. The chemical conversion coating had a limited protection ability due to defects arising from cracks and pores in the coating layer. The sol-gel coating was prepared by using trimethoxymethylsilane (MTMS) and 3-glycidoxypropyltrimethoxysilane (GPTMS) as precursors, and aluminum acetyl acetonate as a ring opening agent. The corrosion protection properties of sol-gel and conversion coatings in 0.35wt% NaCl solution were measured by the electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization test. The EIS results indicated that the resistance of the chemical conversion coating with the sol-gel coating was significantly improved through the sol-gel sealed phosphate-permanganate conversion coating. The results of the potentiodynamic polarization test revealed that the sol-gel coating decreased the corrosion current density ($I_{corr}$). The SEM image showed that the sol-gel coating sealed conversion coating and improved corrosion protection.

• The Journal of Asian Finance, Economics and Business
• /
• v.7 no.10
• /
• pp.865-874
• /
• 2020

In Vietnam, the airline service sector plays an important economic role. However, it is a complicated industry that is open to failures. Negative emotions are an essential variable for the airline service industry because they can trigger a variety of coping behaviors that affect consumer loyalty as well as the image and reputation of the airline service providers. However, negative emotions and the accompanying coping behaviors are often investigated partially or as separate issues, thus leading to an incomplete understanding. This study is conducted to fill this gap by proposing and testing the causal relationship between negative emotions (anger, frustration, regret) and coping behaviors (complaint, negative word-of-mouth (WOM), and switching intention) in the context of the airline industry. Eight research hypotheses are tested. Using the partial least squares structural equation modeling (PLS-SEM) on a sample of 587 passengers in Vietnam, the empirical results show that anger and frustration influence complaints, negative WOM, and switching intention, while regret leads to switching intention and negative WOM. Thus, the research has important academic and practical implications. The empirical outcome could be of major importance for airline companies in planning to provide new services and achieve high performance in the long run.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.5
• /
• pp.215-222
• /
• 2006

The passivity behavior of copper anode containing impurities in copper sulfate solution for electrorefining process was studied at several different levels of impurities such as As, Sb, Bi and Pb. The passivity behavior was investigated by electrochemical techniques (galvanostatic, potentiodynamic and cyclic voltammetry tests) and surface analysis (optical microscopy, electron probe microanalysis, scanning electron microscopy). The results were that arsenic, antimony inhibited passivation and bismuth accelerated it and lead containing anode showed different passivity behavior from above anodes. The improved passivity characteristics could be explained by decrease in oxygen content in passivity film which resulted from a reaction among the impurities, oxygen and copper in the anode. The SEM image revealed that arsenic or antimony containing anode exhibited a porous passivity film and bismuth containing anode showed the compact passivity film and lead containing anode had loose passivity film on anode.

• The Korean Journal of Ceramics
• /
• v.3 no.1
• /
• pp.1-4
• /
• 1997

Diamond film (24$\mu\textrm{m}$) were prepared by Microwave Plasma Chemical Vapor Deposition method from a reactive CO/H$_2$ mixtures. Micro-Raman spectroscopy and micro-cathodoluminescence study were carried out along the crosssection and correlated to SEM observation. CL image of cross-section was also investigated. Peak position, FWHM of Raman spectrum were determined using Lorentzing fit. The stress in this sample is 0.4~0.7 GPa compressive stress, and along the distance the compressive stress reduced. The Raman peak broadening is dominated by phonon life time reduction at grain boundaries and defect sites. Defects and impurities were mainly present inside the film, not at Silicon/Diamond interface.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.707-711
• /
• 2016

A small diameter of SiC fiber mat can produce much higher heat under microwave irradiation than the other types of SiC materials. Fabrication of high strength SiC fiber consists of iodine vapor curing on polycarbosilane precursor and heat treatment process. The curing stage of polycarbosilane fiber was maintained at $150-200^{\circ}C$ in a vacuum condition under the iodine vapor to fabricate a high thermal radiation SiC fiber. The structure and morphology of the fibers were characterized by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TG) and scanning electron microscopy (SEM). In this study, the thermal properties of SiC fiber mats under microwave have been analyzed with an IR thermal camera and its image analyzer. The prepared SiC fiber mats radiated high temperature with extremely high heating rate up to $1100^{\circ}C$ in 30 seconds. The fabricated SiC fiber mats were not oxidized after the heat radiation process under the microwave irradiation.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.4
• /
• pp.1144-1148
• /
• 2014

Here we report a facile synthesis of ruthenium (Ru) Nanoparticles (NPs) by chemical co-precipitation method. The calcination of ruthenium hydroxide samples at $500^{\circ}C$ under hydrogen atmosphere lead to the formation of $Ru^0$ NPs. The size and aggregation of Ru NPs depends on the pH of the medium, and type of surfactant and its concentration. The X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope image (TEM) analyses of particles indicated the formation of $Ru^0$ NPs, and have 10 to 20 nm sizes. As-synthesized $Ru^0$ NPs are characterized and investigated their catalytic ability in click chemistry (azidealkyne cycloaddition reactions), showing good results in terms of reactivity. Interestingly, small structural differences in triazines influence the catalytic activity of $Ru^0$ nanocatalysts. Click chemistry has recently emerged to become one of the most powerful tools in drug discovery, chemical biology, proteomics, medical sciences and nanotechnology/nanomedicine. In addition, preliminary tests of recycling showed good results with neither loss of activity or significant precipitation.

• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.75-79
• /
• 2009

A four beam interference optical system for laser micro structuring using a pulse laser was demonstrated. The four beam interference optical system using a pulse laser(picosecond laser) can fabricate micro structure on mold material(NAK80) directly. Micro structure on the polymer can be reproduced economically by injection molding of the micro structure on the mold material. The four beam interference optical system was composed by the DOE(Diffractive Optical Element) and two lenses. The laser intensity distribution of four beam interference was explained by an interference optics point of view and by the image optics point of view. We revealed that both views showed the same result. The laser power distribution of a $1{\mu}m$ peak pattern was made by the four beam interference optical system and measured by the objective lens and CCD. A $1{\mu}m$ pitch dot pattern on the mold material was fabricated and measured by SEM(Scanning Electron Microscopy).

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.4
• /
• pp.73-80
• /
• 1989

The image sensitive PbO photoconductive films were fabricated ar several deposition conditions such as $O_2$ gas pressure, deposition rate, and substrate temperature. And the effects of these deposition condition on the structural and electrical properties of them were investigated with the aid of scanning electron photomicrographs. X-ray diffraction patterns, and current-valtage chatacteristics. The results show that when PbO film has red tetragonal structure and its dominant orientations are <110> and <010> direction, photocurrent-darkcurrent ratio and light transfer ratio are increase.