• 대한기계학회논문집A
• /
• 제36권9호
• /
• pp.971-978
• /
• 2012

진공침탄법은 이산화탄소의 발생이 없는 친환경적인 열처리 방식으로 알려져 있다. 그러나 진공침탄법은 탄화수소 가스(메탄, 프로판)를 노내에 직접 공급하여 열분해하는 과정을 거침으로써 노내에 그을음이 발생하여 안정적인 조업이 불가능한 단점이 있다. 최근에는 이러한 단점을 극복하기위한 불포화 탄화수소인 아세틸렌가스를 이용한 진공침탄법이 활발히 연구되고 있다. 본 논문에서는 아세틸렌가스를 이용한 진공침탄방식의 침탄 및 확산 시간을 변수로 하여 여러 가지 조건에서 열처리를 진행한 후 가스침탄 열처리된 소재와 기계적 성질을 비교 분석하여 이산화탄소 무 배출 진공침탄 열처리 방법의 활용가능성을 확인하였다. 연구결과 본 연구에서 시도된 진공침탄법은 가스침탄에서 나타나는 입계산화층이 발생하지 않았으며 경도 값은 진공침탄 시험편의 유효경화 깊이가 29.8% 크게 나타났으며 인장강도는 가스침탄보다 10%낮게 나왔으나 허용치를 충분히 만족하는 수준이었다.

• Bulletin of the Korean Chemical Society
• /
• 제11권5호
• /
• pp.415-420
• /
• 1990

A series of copolymers of poly(1,4-phenylenevinylene-co-2,3,5,6-tetramethyl- 1,4-phenylenevinylene), poly(PV-co-TMPV), were prepared in film forms from the precursor polymer films. The sulfonium salt precursor polymers were synthesized by copolymerization of the mixtures of the respective bis(sulfonium salt) monomers. All of the copolymer films could be doped with $FeCl_3$ to have high electrical conductivities and they showed good air stability. The maximum conductivity of the $FeCl_3$-doped films ranged $10^{-3}\;to\;10^2Scm^{-1}$ depending on the composition of the copolymer films. However, these copolymer films could not be doped with iodine. The coplanarity of PV and TMPV units in the main chain appears to be affected by steric effect of the methyl groups in the TMPV units.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 추계학술대회 논문집
• /
• pp.311-315
• /
• 1992

일반적으로 기계구조물에서는 비교적 응력확대계수 K의 해석이 용이한 판 두께를 관통하는 관통크랙보다는 표면에 존재하는 결함에서 발생, 전파하는 표면 크랙이 대부분이다. 표면은 내부보다 소성변형에 대한 저항이 작고, 대기에 직접 접해 있으며, 평활재에 있어서의 인장, 압축이외의 응력은 일반적으로 표면에서 최대가 되는 등의 이유로 내부보다 쉽게 피로재해를 받는다. 침탄질화 열처리를 하는 중요한 목적이 재료 표면에 있어서 경화능과 피로강도의 향상이므로 침탄질화 처리재의 표면 크랙에 관한 연구가 절실히 요구됨은 당연하다.

• 소성∙가공
• /
• 제6권6호
• /
• pp.500-507
• /
• 1997

The conventional closed-die forgings had been applied to the forging of spur gears. But the forgings require high forging-pressure. In this paper, new precision forging technology have been developed. The developed technology is two steps forging process. Good shaped products are forged successfully with lower forging-pressure than those of conventional forging. The accuracy of the forged spur gear obtained by new precision forging technology is set nearly equal to that of cut spur gear of fourth and fifth class in Korean industrial standard.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 추계학술대회논문집
• /
• pp.172-175
• /
• 1997

The conventional closed-die forgings had been applied to the forging of spur gears. But the forgings require high forging-pressure. In this paper, new precision forging technology have been developed. The developed technology is two steps forging process. Good shaped products are forged successfully with lower forging-pressure than those of conventional forging

• 한국산학기술학회논문지
• /
• 제16권4호
• /
• pp.2430-2435
• /
• 2015

상품을 제조할 때 유연성을 높이기 위해서는 칩의 형상분석이 중요한 문제 중의 하나이다. 본 연구에서는 선삭 작업에서 가공 여유각 변경에 따른 피삭재의 가공특성이 어떻게 변화되는지 분석하고 자 하였다. 피삭재는 3가지로 SM45C(기계구조용탄소강), SCM415(크롬몰리브덴강), STS303(스테인리스강)을 선택하여 정해진 가공조건인 회전속도, 이송속도와 가공 깊이에 따라 분석하였다. 특히, 선삭가공에서의 칩의 형상과 인서트 팁의 마모현상을 분석하였다. 결과적으로 칩의 형상은 피삭재의 재질과 가공깊이, 이송속도에 따라 변화됨을 알 수 있었다. 가공이송속도가 0.10mm/rev일 때와 가공깊이 0.3mm일 때가 유동형 칩으로 재질이나 가공특색을 분류하지 않고 가장 좋은 형상을 보였다.

• 한국분말재료학회지
• /
• 제17권6호
• /
• pp.456-463
• /
• 2010

This paper describes the results of the application of Cr-Diamond-like carbon (DLC) films for efficiency improvement through surface modification of spur gear parts in the hydraulic gear pump. Cr-DLC films were successfully deposited on SCM 415 substrates by a hybrid coating process using linear ion source (LIS) and magnetron sputtering method. The characteristics of the films were systematically investigated using FE-SEM, nano-indentation, sliding tester and AFM instrument. The microstructure of Cr-DLC films turned into the dense and fine grains with relatively preferred orientation. The thickness formed in our Cr buffer layer and DLC coating layer were obtained the 487 nm and $1.14\;{\mu}m$. The average friction coefficient of Cr-DLC films considerably decreased to 0.15 for 0.50 of uncoated SCM415 material. The hardness and surface roughness of Cr-DLC films were measured 20 GPa and 10.76 nm, respectively. And then, efficiency tests were performed on the hydraulic gear pump to investigate the efficiency performance of the Cr-DLC coated spur gear. The experimental results show that the volumetric and mechanical efficiency of hydraulic gear pump using the Cr-DLC spur gear were improved up to 2~5% and better efficiency improvement could be attributed to its excellent microstructure, higher hardness, and lower friction coefficient. This conclusion proves the feasibility in the efficiency improvement of hydraulic gear pump for industrial applications.

• 한국해양공학회지
• /
• 제13권4호통권35호
• /
• pp.105-111
• /
• 1999

This study aimed not only to develop the optimization of dissimilar friction welding of pinion gear of a motor vehicle steels of SCM415 and SMn443, but also to develop the application technique of the acoustic emission to accomplish an in-process real-time quality(such as strength and toughness) evaluation during friction welding of the pinion gear by the AE technique.

• 산업공학
• /
• 제13권3호
• /
• pp.405-415
• /
• 2000

The accurate quotation of Available-To-Promise (ATP) plays a very important role in enhancing customer satisfaction and fill rate maximization. However, the complexity of Supply Chain structure, which includes all the linkages among procurement, production, and distribution, makes the accurate quotation of ATP be a quite difficult job. This paper presents a computerized ATP quotation system in global SCM environments where the worldwide headquarter, distribution centers, and manufacturing facilities are globally networked. We modeled the ATP quotation processes with the definition of required data flow and a comprehensive ATP-algorithm was newly developed. The illustrative example shows the efficiency of the proposed system is largely affected by the selection of alternative rules used in ATP-algorithm.

• 한국정밀공학회지
• /
• 제20권11호
• /
• pp.55-63
• /
• 2003

In this study, an experimental research of grinding characteristics using super-abrasives for surface carburized and heat treated SCM415 materials, which were usually used to make a linear motion guide block and were comparatively hard-to-machine materials, was carried out. In order to conduct a high efficiency and a accuracy grinding of such materials, grinding processes using CBN (Cubic boron nitride) and 38P grinding wheels have been attempted on a surface grinding machine. The grindability according to each grinding conditions was evaluated by means of a grinding force, a surface roughness and a residual stress. The experimental methods and results were presented in this paper. And also, from a proposed truing method the CBN wheels that combined a copper and a break truer gave a full scope to the wheel's performance.