• 대한전자공학회논문지SD
• /
• 제40권3호
• /
• pp.1-9
• /
• 2003

본 연구에서는 1-단자 표면탄성파 공진기를 적용한 사다리형 구조 필터에 대한 전극 두께, 공진기의 반사기 하중 및 정적 정전용량비에 따른 주파수 응답특성의 고찰이 이루어졌으며, 최적화된 매개변수를 이용하여 송신 및 수신단용 RF 필터를 제작하였다. 제작된 필터는 800㎒ 대역 이동통신 시스템에 적용 가능하며, 외부회로에 의한 임피던스 정합이 필요하지 않다. 36°LiTaO₃ 압전기판 위에 Al-Cu(W 3%) 전극을 형성하여 제작하였으며, 3.8㎜×3.8㎜×1.5㎜세라믹 패키지에 실장되었다. 통과대역(25 ㎒)에서의 최소 삽입손실은 2.3 dB, 3-dB 대역폭은 약 33 ㎒, 통과대역 리플은 0.5 dB 미만이며, 약 30 dB 이상의 저지대역 감쇄를 확보할 수 있었다. 또한, 제작된 RF 필터의 내전력성 및 온도 변화에 따른 주파수 응답특성 실험을 통해 약 3.5 W의 내전력성과 -20℃∼80℃에서 최대 0.09 dB/℃의 3-dB 삽입손실 변화를 측정할 수 있었다.

• 펄프종이기술
• /
• 제43권3호
• /
• pp.59-65
• /
• 2011

The saw dust of tropical hardwood, Nyatoh(Palaquium Spp.), was used as a raw material for the preparation of the high valued microcrystalline cellulose(MCC). Three pulping methods, soda pulping, Kraft pulping, and acid-sulfite pulping were applied to obtain cellulose from the saw dust. The residual impurities were removed with the additional bleaching processes: (A) $ClO_2{\rightarrow}H_2O_2$; (B) $ClO_2{\rightarrow}O_3$; (C) $O_3$. For the acid treatment for MCC preparation, the $H_2SO_4$, with three concentration, 20%, 40%, 60% were applied and the effects of $H_2SO_4$ concentration on the properties of MCC were evaluated. The results indicated that the MCC obtained by acid-sulfite pulping followed with $O_3$ treatment and 40% $H_2SO_4$ treatment showed less residual lignin, higher brightness and crystallinity than that of Avicel MCC.

• 한국정밀공학회지
• /
• 제18권5호
• /
• pp.130-136
• /
• 2001

Generally, a metal slitting saw is plain milling cutter with thickness less than 3/16 inch. This is used for cutting a workpiece that high dimensional accuracy and surface finish is necessary. A small thin milling cutter like a metal slitting saw is useful for machining a narrow groove. In this case, built up edge(BUE) is severe at each tooth and affects the surface integrity of the machined surface and tool wear. It is well known that tool geometry and cutting conditions are decisive factors to remove BUE. In this paper, we optimized the geometry of the milling cutter and selected cutting conditions to remove BUE by the experimental investigation. The experiment was planned with Taguchi method based on the orthogonal array of design factors such as coating, rake angle, number of tooth, cutting speed, feed rate. Response table was obtained from the number of built-up edge generated at tooth. The optimized tool geometry and cutting conditions could be determined through response table. In addition, the relative effect of factors was identified bh the analysis of variance (ANOVA). Finally, coating and cutting speed turned out important factors for BUE.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2012년도 춘계학술발표대회
• /
• pp.884-887
• /
• 2012

무선 센서 네트워크 기술은 상시적으로 물리정보를 획득할 수 있기 때문에 광범위한 응용분야에서 수요가 증가하고 있다. 또한 무선 센서 네트워크에 적용되는 무선 센서 시스템은 일반적으로 배터리를 장착하여 회로에 전력을 공급해주는 방식을 사용한다. 그러나 센서가 적의 기지근처, 인체 조직내 삽입, 건물의 내벽 등과 같이 배터리를 교체할 수 없는 곳에 위치해 있는 경우, 반영구적인 사용에 제한이 있기 때문에 무전원 무선 센서의 개발이 절실히 필요하다. 특히, 이러한 센서를 새롭게 개발하고 검증하려며 센서의 주파수 특성을 분석해야 하는데 기존에는 단순한 파형만을 분석할 수 있는 일반적인 계측기를 사용할 수밖에 없었다. 따라서 본 논문에서는 기존의 계측기보다 유연성 있고 효율적으로 무전원 무선 센서의 개발과 검증이 가능하도록 신호의 모니터링과 신호발생기를 에뮬레이션하는 NI LabVIEW기반의 SAW System Analyzer와 SAW Reader Emulator 시스템을 설계하고 개발하였다.

• 한국음향학회지
• /
• 제19권2호
• /
• pp.33-39
• /
• 2000

낮은 형상요소를 갖는 표면탄성파 대역통과 필터의 주파수 특성을 구현하기 위하여 35° Y-cut Quartz 표면에 빗살무늬 변환기를 형성시켜 모의실험을 수행하였으며, 전극재료로는 Al을 이용하였다. 이 모의실험에서 얻은 조건들로부터 필터를 설계하였으며, 필터의 입력단에는 apodization weighted형 빗살무늬 변환기를 이용하고, 출력단에는 withdrawal weighted형 빗살무늬 변환기로 필터를 구성하였다. 또한, 입·출력 빗살무늬 변환기의 전극 수는 리플의 영향을 최소화하기 위해 Kaiser-Bessel 창함수를 이용하였으며, 각각 2200쌍과 1000쌍으로 하였다. 그리고, 빗살무늬 변환기 전극의 폭은 6㎛, 간격은 5.75㎛ 및 두께는 표면탄성파 파장과의 비를 고려해 6000Å으로 할 때 최적의 결과를 얻을 수 있었으며, 구경은 임피던스 정합을 위해 2mm로 하였다. 제작한 표면탄성파 대역통과 필터의 중심주파수는 70MHz, 형상요소는 1.3이하, 1.5dB에서의 통과 대역은 1.3MHz, 저지대역은 -45dB, 삽입손실은 19dB, 통과 대역폭 내의 리플은 1dB정도로 측정되었다. 따라서, 제작한 필터의 주파수 응답과 특성은 설계조건과 잘 일치하였다.

• 대한치과기공학회지
• /
• 제32권4호
• /
• pp.403-415
• /
• 2010

Purpose: The purpose of this study was to examine the eyesight and life habits of college students in an attempt to provide some information on the protection of their eyesight. Methods: The subjects in this study were 311 students in the department of dental technology at a college of health, on whom a survey was conducted. A crosstabulation analysis was carried out to show the joint distribution of general characteristics and several variables involving the use of glasses or contact lenses and life habits. Results: 77.5% of the students currently wore glasses due to weak sight. 9.3% took an eye test on a regular basis, and 31.2% did that every six months. As for the length of the length of daily mean reading time, 55.3% spent one hour or less reading books. The most common distance between eyes and books during their reading(44.7%) was 21 to 25. Concerning a reading posture, the biggest group(54.3%) lay down or lay on their face while they read books. 45.0 % spent less than an hour watching TV per day on average, and 27.0% were on the computer for 30 minutes to less than an hour per day on average. The greatest group(63.0%) made use of basic indoor lighting when they were on the computer at night, and 62.1% saw eye doctors to take an eye test. In relation to how to protect eyesight, the biggest group(50.5%) spent less time being on the computer. Conclusion: As the eyesight of college students fails due to reading, TV, computer, and improper ways and posture of doing or using those things, every college definitely should provide education on eye health as one of general education courses.

• 한국지반공학회논문집
• /
• 제21권1호
• /
• pp.29-41
• /
• 2005

우리나라의 소규모 항만이나 어항인 경우에 설계파는 낮지만 지반조건이 좋지 않은 경우가 많기 때문에 기존의 방파제 축조공법을 이용할 경우 비용이 커질 뿐만 아니라 건설재료의 확보가 어려운 실정이다. 따라서 설계파가 비교적 낮은 경우에 저렴하게 적용할 수 있는 새로운 형식의 방파제에 대한 수요가 증가함에 따라, 본 연구에서는 지반에 대한 특별한 처리 없이 간편하게 설치할 수 있는 가로널식 방파제를 개발하였다. 이 논문은 개발된 가로널식 방파제에 대해 방파제의 근입깊이 및 보강기법, 배치 형태 등 다양한 조건에 따른 방파제의 횡방향 거동을 분석한 것으로 이를 위해 느슨한 모래지반을 대상으로 모형 토조실험을 수행하였다. 실험 결과, 근입깊이 이외에도 경사 버팀보나 앵커등 보강재의 효과 및 방파제 배치 형식에 따른 경향을 확인하였다.

• 한국가시화정보학회지
• /
• 제14권1호
• /
• pp.57-61
• /
• 2016

We report a finding of fast(exceeding 2,000 K/s) heating of polydimethylsiloxane(PDMS), one of the most commonly-used microchannel materials, under cyclic loadings at high(~MHz) frequencies. A microheater was created based on the finding. The heating mechanism utilized vibration damping of sound waves, which were generated and precisely manipulated using a conventional surface acoustic wave(SAW) microfluidic system, in PDMS. The penetration depths were measured to range from $210{\mu}m$ to $1290{\mu}m$, enough to cover most microchannel heights in microfluidic systems. The energy conversion efficiency was SAW frequency-dependent and measured to be the highest at around 30 MHz. Independent actuation of each interdigital transducer(IDT) enabled independent manipulation of SAWs, permitting spatiotemporal control of temperature on the microchip. All the advantages of this microheater facilitated a two-step continuous flow polymerase chain reaction(CFPCR) to achieve the billion-fold amplification of a 134 bp DNA amplicon in less than 3 min. In addition, a technique was developed for establishing dynamic free-form temperature gradients(TGs) in PDMS as well as in gases in contact with the PDMS.

• Wind and Structures
• /
• 제23권2호
• /
• pp.91-107
• /
• 2016

Flow-excited acoustic resonance in ducted cavities can produce high levels of acoustic pressure that may lead to severe damage. This occurs when the flow instability over the cavity mouth, which is created by the free shear layer separation at the upstream edge, is coupled with one of the acoustic modes in the accommodating enclosure. Acoustic resonance can cause high amplitude fluctuating acoustic loads in and near the cavity. Such acoustic loads could cause damage in sensitive applications such as aircraft weapon bays. Therefore, the suppression and mitigation of these resonances are very important. Much of the work done in the past focused on the fluid-dynamic oscillation mechanism or suppressing the resonance by altering the edge condition at the shear layer separation. However, the effect of the downstream edge has received much less attention. This paper considers the effect of the impingement edge geometry on the acoustic resonance excitation and Strouhal number values of the flow instabilities in a ducted shallow cavity with an aspect ratio of 1.0. Several edges, including chamfered edges with different angles and round edges with different radii, were investigated. In addition, some downstream edges that have never been studied before, such as saw-tooth edges, spanwise cylinders, higher and lower steps, and straight and delta spoilers, are investigated. The experiments are conducted in an open-loop wind tunnel that can generate flows with a Mach number up to 0.45. The study shows that when some edge geometries, such as lower steps, chamfered, round, and saw-tooth edges, are installed downstream, they demonstrate a promising reduction in the acoustic resonance. On the other hand, higher steps and straight spoilers resulted in intensifying the acoustic resonance. In addition, the effect of edge geometry on the Strouhal number is presented.

• 복식
• /
• 제54권5호
• /
• pp.109-123
• /
• 2004

The purpose of this study is to examine features of parts of Jikryung and relations among the features. Results of the study can be described as follows. 1. The short front and long rear of Jikryung was changed into the long front and long rear of the dress in the late 16th century. Kalgit of quasi-square style as double collar was changed into that of common collar in the late 16th century and then into common semi-circle collar in the early 17th century, when double Sup was also changed Into single Sup. Narrow sleeves of Jikryung were replaced by bean chaff-shaped in the late 16th century and then by wide ones in the early period of the next century. The shape of the side hem of Jikryung was changed from rectangle into trapezoid in the early 17th century Triangle-shaped Moo was changed into trapezoid-shaped one in the late 16th century and then again into triangle in the late 17th century 2. Changes in shapes of the parts of Jikryung were made with them correlated. The collar of Jikryung saw change in its form from double to common as its width was reduced. Double Sup was changed into single one and the narrow, short coat string into the long one as Jikryung became a dress needing less adjustment. The sleeves widened as the length of whajang increased. The side hem of Jikryung saw change in its shape from rectangular to trapezoidal one as its position was changed. Trapezoidal Moo was replaced by triangular one as the sleeve of Jikryung was changed in shape. 3. Changes in shapes of the parts of Jikryung influenced the aesthetic beauty of the dress itself In its first period, Jikryung was simple with long, slim silhouettes. In its second period, the dress was rich with increased volume. Finally in its third period, the dress was characterized by the harmony of simpleness and richness.