• Steel and Composite Structures
• /
• 제14권4호
• /
• pp.349-365
• /
• 2013

Structures consisting of concrete and steel parts, which are irregular in damping ratios are investigated. This investigation is a code-based seismic design of such structures. Several practical difficulties encountered, due to inherent differences in the nature of dynamic response of each part, and the different damping ratios of the two parts. These structures are irregular in damping ratios and have complex modes of vibration so that their analysis cannot be handled with the readily available commercial software. Therefore, this work aims to provide simple yet sufficiently accurate constant values of equivalent damping ratios applied to the whole structure for handling the damping irregularity of such structures. The results show that the equivalent damping ratio changes with the height of the building and the kind of the structural system, but it is constant for all accelerations values. Thus, available software SAP2000 applied for seismic analysis, design and the provisions of existing seismic codes. Finally, evaluation of different kinds of structural system used in this research to find the most energy dissipating one found by finding the best value of quality coefficient.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.347-351
• /
• 1997

A micromachined piezoelectic cantilever transducer,which works both as a microphone and as a microspeaker,has been fabricated and tested. The 2000*2000*3.mu.m .sap2. cantilever has oxide(ZnO)piezoelectric thin film on a supporting layer of low-pressure chemical-vapor-deposited(LPCVD)low-stress siliconnitride. A highlight of the fabrication process which may also be relevant for other micromachined stuctures is the technique for producing a flat,multilayer cantilever. The measured microphone sensitivity is fairly constant at 2 mV/.mu.bar in the low frequency range and rise to 20 mV/.mu.bar at the lowest resonant frequency of 890 Hz. The 2 mV/.mu.bar sensitivity is the highest report to data for a microphone with a micromachined diaphragm. When measured into a 2 cm/sap3 coupler with 4V (zero-park)drive,the microspeaker output sound pressure level(SPL) is 75 dB at 890 Hz. It increases to approximately 100dB SPL at 4.8kHz with 6V(zero-park)drive. The measured microphone frequency response agrees well with the results of an ABAQUS simulation.

• Steel and Composite Structures
• /
• 제22권4호
• /
• pp.733-744
• /
• 2016

In this study, optimum structural designs of braced (non-swaying) planar steel frames are investigated by using one of the recent meta-heuristic search techniques, teaching-learning based optimization. Optimum design problems are performed according to American Institute of Steel Construction- Allowable Stress Design (AISC-ASD) specifications. A computer program is developed in MATLAB interacting with SAP2000 OAPI (Open Application Programming Interface) to conduct optimization procedures. Optimum cross sections are selected from a specified list of 128W profiles taken from AISC. Two different braced planar frames taken from literature are carried out for stress, geometric size, displacement and inter-storey drift constraints. It is concluded that teaching-learning based optimization presents robust and applicable optimum solutions in multi-element structural problems.

• Structural Engineering and Mechanics
• /
• 제63권5호
• /
• pp.607-615
• /
• 2017

This study presents optimum design of plane steel bridges considering corrosion effect by using teaching-learning based optimization (TLBO) method. Optimum solutions of three different bridge problems are linearly carried out including and excluding corrosion effect. The member cross sections are selected from a pre-specified list of 128 W profiles taken from American Institute of Steel Construction (AISC). A computer program is coded in MATLAB to carry out optimum design interacting with SAP2000 using OAPI (Open Application Programming Interface). The stress constraints are incorporated as indicated in AISC Allowable Stress Design (ASD) specifications and also displacement constraints are applied in optimum design. The results obtained from analysis show that the corrosion effect on steel profile surfaces causes a crucial increase on the minimum steel weight of bridges. Moreover, the results show that the method proposed is applicable and robust to reach the destination even for complex problems.

• Advances in Computational Design
• /
• 제1권3호
• /
• pp.221-234
• /
• 2016

The present study dictates the behavior of shear wall under a seismic event in slender high rise buildings, and studies the effect of height, location and distribution of shear wall in slender high rise building with and without boundary elements induced by the effect of an earthquake. Shear walls are located at the sides of the building, to counter the earthquake forces. This study is carried out in a 12 storeys building using SAP2000 software. The obtained results disclose that the behavior of the structure is definitely affected by the height and location of shear walls in slender high rise building. The stresses are concentrated at the limit between the shear wall region and the upper non shear wall especially for shear walls without columns. Displacements are doubled between the shear wall region and the upper non shear wall especially for shear walls without columns.

• Steel and Composite Structures
• /
• 제24권2호
• /
• pp.227-237
• /
• 2017

This paper presents optimization of a long-span portal steel frame under dynamic wind loads using a surrogate-assisted evolutionary algorithm. Long-span portal steel frames are often used in low-rise industrial and commercial buildings. The structure needs be able to resist the wind loads, and at the same time it should be as light as possible in order to be cost-effective. In this work, numerical model of a portal steel frame is constructed using structural analysis program (SAP2000), with the web-heights at five locations of I-sections of the columns and rafters as the decision variables. In order to evaluate the performance of a given design under dynamic wind loading, the equivalent static wind load (ESWL) is obtained from a database of wind pressures measured in wind tunnel tests. A modified formulation of the problem compared to the one available in the literature is also presented, considering additional design constraints for practicality. Evolutionary algorithms (EA) are often used to solve such non-linear, black-box problems, but when each design evaluation is computationally expensive (e.g., in this case a SAP2000 simulation), the time taken for optimization using EAs becomes untenable. To overcome this challenge, we employ a surrogate-assisted evolutionary algorithm (SAEA) to expedite the convergence towards the optimum design. The presented SAEA uses multiple spatially distributed surrogate models to approximate the simulations more accurately in lieu of commonly used single global surrogate models. Through rigorous numerical experiments, improvements in results and time savings obtained using SAEA over EA are demonstrated.

• Journal of Applied Biological Chemistry
• /
• 제43권3호
• /
• pp.170-175
• /
• 2000

A pot-lysimeter experiment was conducted with 3-year-old 'Tsugaru' apple (Malus domestica Borkh) trees to examine the changes in oxygen diffusion rate (ODR) with lateral flow velocity of water through soil. The influence of lateral water flow velocity on water relations and elemental content in leaf, and sap temperature distribution patterns of the xylem of trees were also determined. Trees were grown under four soil water regimes: (1) fast laterally flowing (FWT, $2.50{\times}10^{-4}cm\;s^{-1}$), (2) slow laterally flowing (SWT, $0.25{\times}10^{-4}cm\;s^{-1}$), and (3) stagnant water table (WLT) at 60-cm, and (4) drip-irrigation at -40 kPa of soil matric potential as a control. The rate of $O_2$ diffusion converged near $2{\times}10^{-3}g\;m^{-2}\;min^{-1}$ for FWT and control soils, but decreased below $1{\times}10^{-3}g\;m^{-2}\;min^{-1}$ 40 days after treatment (DAT) for WLT soils. For SWT soils, however, the ODR at 15 cm below the soil surface was similar to that of control, but at 45 cm below the soil surface, ODR was similar to that of the WLT treatment. Leaf water potential of FWT and SWT plants was similar to that of control plants, but the values for SWT plants declined by 98 DAT. Leaf water potential of WLT plants decreased from -1.86 MPa (9 DAT) to -2.41 MPa (59 DAT) and finally down to -2.70 MPa. The sap temperature measured at 1100-hr was lowest at top and highest at bottom for FWT and control plants, but this pattern of SWT and WLT plants was disturbed from 29 DAT. However, for SWT plants, such thermal disturbance of sap temperature disappeared from 63 DAT.

• 한국지리정보학회지
• /
• 제8권3호
• /
• pp.96-106
• /
• 2005

원격탐사와 GIS 기법는 시공간 측면에서 매우 귀중한 정보를 제공할 수 있으며, 홍수와 같은 재해 발생시 홍수발생 지역에 대한 매핑, 모니터링 빚 재해지역 관리 등에 있어 매우 유용한 정보를 제공할 수 있다. 지난 2000년 메콩강 유역의 Tonle Sap호에서 발생한 홍수에 의해 많은 피해가 발생하였으며, 특히 7월과 10월 사이에 두 차례의 홍수 피크가 기록되었다. 본 연구에서는 홍수피해에 대한 정량적인 분석을 위해 ISODATA와 세크멘테이션 기법을 이용하여 Landsat ETM+와 RADARSAT 영상을 분석하였다. 그러나, 영상으로부터 분석된 범람면적이 구름과 복잡한 지표피복물 등으로 인해 실제 홍수피해 상황을 정확히 반영하지 못했다. 따라서, 이러한 문제점을 해결하고자 GIS 기능 중 비용-거리 (cost-distance) 기법을 이용하여 홍수범람 면적을 분석하였으며, 분석결과는 수치표고자료(DEM)와 중첩하여 홍수량을 계산하였다. 계산된 홍수량은 수리모형인 MIKE 11의 모델링 결과와 비교하였다. 계산결과 영상 내에 많은 구름이 존재하는 Landsat ETM+ 영상의 경우와 복잡한 지표피복이나 시스템 변수 등의 영향으로 홍수피해 지역을 정확히 분류하기 어려운 RADARSAT 영상에서도 좋은 결과를 얻을 수 있었다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2000
• /
• pp.455-462
• /
• 2000

In this study seismic response of a base-isolated bridge for soil types is compared. Bilinear model is used for lead rubber bearing(LRB). Accelerograms whose response spectrum matches the design spectrum for soil types are used as earthquake ground excitation. Nonlinear time history analyses using the SAP2000 program is performed. The results show that seismic response of a base-isolated bridge is increased as the soil becomes soft.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.325-330
• /
• 2000

The objective of this study is firstly to frame up the seismic safety of concrete gravity dams. It is necessary to analyze seismic response and evaluate seismic performance of concrete gravity dams during earthquake. In this study, seismic damage and dynamic analysis of concrete gravity dams using SAP2000 program are performed. Additional dynamic water pressure due to earthquake considered as additional mass for numerical seismic analysis. But, further research will be needed for the seismic stability of dams.