• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2007년도 춘계학술발표회 논문집
• /
• pp.277-281
• /
• 2007

Quite a while ago, Organizations which have slope DB system was running slope of management in several. Frequently, Slope failure was happened by abnormal weather and limit of valuation system at the managed slope. Analysis of other organization slope DB systems is very important that slope DB system maintains same regions on geology. In Korea, slope DB system was running at KEC(Korea Expressway Corporation), Korail(Korea Railroad), and KIGAM(Korea Institute of Geoscience and Mineral Resources). We research theirs DB constructing. For reviewed slope DB system of other country, we searched NLIC(Natural Landslide Information Center)'s DB system in U.S.A., GEO's LPM(landslide Prevention Measures) program in Hongkong, DPRI' ILC(International Consortium on Landslides) program in Japan, and AGSO(Australian Geological Survey Organization)'s NGVUC program in Australia.

• Journal of Biosystems Engineering
• /
• 제3권2호
• /
• pp.35-61
• /
• 1978

동력경운깅가 일반 경사지에서 견인주행하는 경우 견인주행성능과 주행특성을 구명하기 위하여 토양의 종류 및 상태는 일정하게 하고 지면의 기하학적 조건과 견인주행속도 및 견인하중을 변수로 하여 외부동력전달계의 시점인 좌우차륜과 토양간에 발생하는 차륜구동력 및 굴름정항과 Engine에서 구동륜까지 내부전달계를 통하여 전달된 동력의 이론치와 실험치와의 부합여부를 검정하고 부가적으로 동력경운기가 경사지기계화의 동력기로써의 가능성여부와 문제점을 찾으려한다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.511-518
• /
• 2000

Characteristics of joint orientation, length, spacing and their distribution are very important factors for slope stability, Especially, the effect of joint spacing is an essential factor of slope stability. This study is to analyze the effect of joint spacing in cases of sliding and toppling, which is a typical failure mode. Joint spacing can divided into vertical spacing(spacing) and horizontal spacing(gap). And then, the spacing/length ratio of joint directly affect rock slope failure. When the ratio is below 0.05, the possibility of failure is rapidly increased. In case of toppling, the possibility of failure depends on the ratio of spacing to height of slope ratio slope. As the ratio decreases, the possibility of toppling failure increased. The critical ratio of spacing to height of slope is determined by the dip angle of the slope and the orientation of joint sets.

• Journal of Biosystems Engineering
• /
• 제3권2호
• /
• pp.34-34
• /
• 1978

동력경운깅가 일반 경사지에서 견인주행하는 경우 견인주행성능과 주행특성을 구명하기 위하여 토양의 종류 및 상태는 일정하게 하고 지면의 기하학적 조건과 견인주행속도 및 견인하중을 변수로 하여 외부동력전달계의 시점인 좌우차륜과 토양간에 발생하는 차륜구동력 및 굴름정항과 Engine에서 구동륜까지 내부전달계를 통하여 전달된 동력의 이론치와 실험치와의 부합여부를 검정하고 부가적으로 동력경운기가 경사지기계화의 동력기로써의 가능성여부와 문제점을 찾으려한다.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2004년도 추계학술발표회 논문집
• /
• pp.217-222
• /
• 2004

In this study, cutting slope's digital image has acquired by using video camera attached at RC helicopter. Resulted RMSE from image processing was approximately x-direction 0.27m, y-direction 0.23m and z-direction 0.35m. Application of these methods makes it convenient that acquisition of digital image about before and after the construction work of road cutting slope. Also systematical cutting slope's information acquisition will be possible by cutting slope's quantitative and qualitative analysis.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.16-26
• /
• 2002

As the slope designs had simply followed some slope guidelines during 1960's∼1970's, of which the main purpose was to estimate earth work quantities in the feasibility stage, slope failures had been experienced in Korea Highways. Various site investigation methods for highway cut-slopes have been continuously developed, and major cut-slope failures caused by slope instability have rapidly reduced. The failure mode of recent cut-slope failures in highways during typhoon RUSA No.15. featured a debris flow in soil mass activated by flowing water. The study of the surface soil scour and the debris flow caused by heavy rainfall must be done to protect the cut-slope failures in the future

• Journal of the Korean Wood Science and Technology
• /
• 제31권3호
• /
• pp.35-41
• /
• 2003

The mechanical and physical properties of wood are strongly dependent upon the slope of grain. Specially, tensile strength is more severely affected by the slope of grain. Therefore, tension tests were performed on small thin wood samples made from Pinus radiata with varying the slope of grain. Determining the tensile strength for clear thin wood samples the other variabilities associated with material, size, drying, defects, etc were discarded. Slope of grain was measured by the slope of grain indicator and actual slope of grain was also determined by a protractor. Correlation coefficients between machine measured and actual slope of grain for 40 pieces of 2×20 mm, 300 mm long Pinus radiata were 0.84 for wide face measurement. Results also showed that tensile strength and MOE from stress wave tests decreased with increasing the slope of grain. This study did not establish a relationships for tensile strength and MOE from stress wave with slope of grain. However, the trends of MOEs from stress wave test with both slope of grain are agreed well with Hankinson's equation. Predicted tension strength curve by Hankinson's equation was also agreed well with the experimental data over the range from 0 to 13 degrees for slope of grain.

• Journal of Biosystems Engineering
• /
• 제30권1호
• /
• pp.1-7
• /
• 2005

When a slope tractor works on the slope land, it travels usually along the contour and slope line. In that case, the efficiency of work generally decreases and the safety of the operator caused by the overturn of the tractor should be considered. Maintaining the tractor body being horizontal during the travel is crucial to solve problems. To overcome such a problem, an automatic leveling control system for slope tractor has been developed. The system composed of sensor for measuring rolling and pitching inclination of the slope tractor chassis, controller, hydraulic control system and mechanism. The limit angle of the leveling control was set up to be ${\pm}15^{\circ}C$ for rolling, ${\pm}7^{\circ}C$ for pitching. The proposed control and hydraulic power system was implemented to the prototype slope tractor. This paper shows results about development of the automatic leveling mechanism and response properties for slope tractor.

• 한국의류학회지
• /
• 제27권3_4호
• /
• pp.429-440
• /
• 2003

The purpose of this study is to classify the types of men's shoulders through the criteria which represent the characteristic of men's shoulders. In addition, we introduce new bodice patterns depending on our classification. We have the fo11owing conclusions based on our sample size of 200 men's shoulders: 1. The result of factor analysis indicates that six factors are extracted and they consist of 62.3% of total variance. We then choose three factors as standard items for our classification of the shape of men's shoulders. 2. We divide the shape of shoulders into three categories: bent, slopeness, and thickness. Each category is divided into three subcategories. (a) Bent: If one's shoulders are bent forward or backward, then we call them front or back-bent type. Otherwise, they are called standard-bent type. (b) Slopeness: If one's shoulders have an easy or steep slope, then we call them easy or steep slope type. Or else, they are called standard slope type. (c) Thickness: If one's shoulders are thick or thin, then we call them thick or thin type. Otherwise, we call them standard thick type. 3. According to the frequency based on our data entries of 200 men's shoulders, we introduce five new types of men's shoulders. 76.5% of examined men's shoulders belong to one of these five types: (a) 8.0% of standard slope and back-bent type: (b) 9.5% of easy slope and standard-bent type; (c) 45.5% of standard slope and standard-bent type; (d) 5.5% of steep slope and standard-bent type; (e) 8.0% of standard slope and back-bent type. 4. The suitability of new basic bodice patterns based on the types of men's shoulders are demonstrated by the high approval rate of the subjects who participate in testing.

• 지질공학
• /
• 제24권3호
• /
• pp.383-396
• /
• 2014

사면붕괴에 따른 재해에 효과적으로 대응하기 위해서는 사면의 상태, 특성, 안정성과 사면붕괴시의 피해도에 대한 분석이 필요하다. 이 연구에서는 사면 관리에 필요한 다양한 항목을 포함하고 있는 사면기호시스템(Slope Code System, SCS)을 제안하고 있다. SCS는 사면의 상태, 지질특성, 공학적 안정성, 피해도 등을 평가하여 사면의 특성을 구체적으로 표현할 수 있으며, 평가방법도 비교적 쉽게 할 수 있다. SCS는 5가지의 평가 요소로 구성되어 있는데, '요소-1'은 사면의 구성물질을 나타내며, '요소-2'는 사면의 지질학적 특성을 성인에 따른 암종(rock type)과 지질구조로 나타낸다. '요소-3'은 사면의 공학적 안정성 평가하며, '요소-4'는 보호 보강 상태를 나타낸다. 마지막으로 '요소-5'는 사면붕괴 시 발생될 수 있는 피해의 정도를 나타낸다. SCS의 5가지 평가 요소들은 각각 평가 결과를 나타내는 고유한 분류 기호들을 가지고 있으며, 각 요소별 평가 결과로부터 부여된 5개의 기호들을 조합하여 사면의 종합적인 상태를 나타낸다. SCS는 사면의 상태, 특성, 공학적 안정성, 피해도 등을 종합적으로 평가하므로 사면의 유지관리에 효율적으로 사용될 수 있을 것으로 판단된다.