• Elastomers and Composites
• /
• v.6 no.1
• /
• pp.53-70
• /
• 1971

We have studied the blending effects of cis-1,4-polybutadiene (CBR) and styrene-tutadiene rubber at various blending ratios of 100 : 0, 70 30, 50 : 50, 30 : 70, 0 : 100, and of carbon black ISAF and HAP at various compounding ratios of 45 PHR, 55 PHR, 65 PHR, for tyre tread rubber. The results obtained are summerized as follows; 1. For tyre tread rubber, it was found to increased efficiency to use SBR polymer only than to use the blending ratio CB/SBR=30/70 below. But it was observed that the latter was adapted for the bus or truck tyre and the former for the passenger tyre. 2. Excellent efficiency was obtained in case of carbon black compounding ratio of 55%, and also the compounding of ISAF made better efficiency than that of HAF. 3. Carbon black was more efficient to SBR than to CB. 4. For the aging ratio, the compounding rubber of NR was the highest, and the ratio was decreased in order of the compounding rubber of oil-extended SBR or CB polymer only, the compounding rubber of non oil-extended SBR or CB polymer only, and the blending rubber.

• Elastomers and Composites
• /
• v.41 no.3
• /
• pp.182-193
• /
• 2006

The retardation effects of a new polymeric UV stabilizer, DGEBA-HALS, on the UV degradation of SBR and NR were investigated in this study. The UV degradation behaviors of three different rubber compounds, without any photostabilizer and with commercial Cyabsorb UV-3529 and DGEBA-HALS, were compared. Also, the physical characteristics such as Young's modulus, tensile strength, blow-off deformation and crosslink density were examined. The Young's modulus was increased by UV irradiation for all samples, and the tensile strength, after UV irradiation, of the compound with UV stabilizer was better than that of the compound without stabilizer. Especially, the tensile strength of UV irradiated NR was improved by adding DGEBA-HALS. The results of blow-off deformation were in accord with those of Young's modulus. The degree of transmission of SBR compounds obtained from UV-vis transmission spectra was improved about 4% by adding the UV stabilizer. Commercial Cyabsorb UJV-3529 and DGEBA-HALS showed similar trends of transmission. The SEM photographs of SBR surface showed that the size of cracks created by UV irradiation became smaller by adding UV stabilizer. In particular, it is observed that the stabilization effect of DGEBA-HALS was better than that of commercial Cyabsorb UV-3529.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1164-1168
• /
• 2007

질소 및 인 동시제거 공정 중 대표적인 연속회분식반응조(Sequencing Batch reactor: SBR)는 비교적 간편한 운전방법과 저렴한 건설비, 유입수의 부하변동에 큰 영향을 받지 않는 소규모 하수처리에 적합한 공정으로 알려져 있다. 또한 SBR 공정은 기존 활성슬러지 공법에 비해 적은 부지로 많은 양의 폐수를 처리할 수 있고 유입수 수질 및 유량변동에 따라 다양한 운전주기를 변화할 수 있으며, 유기물 제거뿐만 아니라 반응조의 변형에 의해 영양염류의 제거가 가능한 장점이 있다. 본 연구에서는 bench scale SBR 실험을 통하여 질산염의 탈질속도 및 용해성 인의 흡수와 방출속도를 측정하고, SBR 공정의 무산소조건에서 인흡수 및 탈질을 동시에 수행하는 DPB 존재의 가능성을 파악하고자 하였다. 연구결과 무산소조건에서 S-P의 방출과 흡수가 동시에 진행되었으며, 무산소조건에서 S-P의 방출속도는 $0.08{\sim}0.94\;kgS-P/kgMLSS{\cdot}d$, 흡수속도는 $0.012{\sim}0.1\;kgS-P/kgMLSS{\cdot}d$를 나타내었다. 무산소조에서 S-P의 방출 및 흡수가 진행되는 동안 탈질과정도 함께 진행되었으며, 각각의 F/M비에서 탈질속도를 측정한 결과 F/M비 $0.44\;kgCOD/kgMLSS{\cdot}d$에서는 최대 $0.16\;kgNO_3^-N/kgMLSS{\cdot}d$의 탈질속도를 나타내었다. S-P이 방출되지 않는 경우와 방출되는 경우의 비탈질속도를 비교한 결과 S-P이 방출되지 않는 경우의 비탈질속도가 S-P이 방출되는 경우의 비탈질속도보다 높았다. 이렇게 S-P이 방출되는 경우의 비탈질속도가 더 낮은 이유는 무산소 조건에서 탈질과 S-P의 방출 및 흡수가 동시에 일어나는 경우 S-P의 방출에 관여하는 미생물과 탈질에 관여하는 미생물간의 경쟁반응 때문으로 판단된다.응답법의 적용이 가능함을 보였고, 이는 보다 복잡한 관망에서의 천이류 해석이 가능함을 시사한다.$경상도지리지$\lrcorner$(慶尙道地理志)에는 상주가 8곳으로 1/3의 자기 생산을 담당하고 있었다. $\ulcorner$경상도지리지$\lrcorner$(慶尙道地理志)에는 $\ulcorner$세종실록$\lrcorner$(世宗實錄) $\ulcorner$지리지$\lrcorner$(地理志)와 동년대에 동일한 목적으로 찬술되었음을 알 수 있다. $\ulcorner$경상도실록지리지$\lrcorner$(慶尙道實錄地理志)에는 $\ulcorner$세종실록$\lrcorner$(世宗實錄) $\ulcorner$지리지$\lrcorner$(地理志)와의 비교를 해보면 상 중 하품의 통합 9개소가 삭제되어 있고, $\ulcorner$동국여지승람$\lrcorner$(東國與地勝覽) 에서는 자기소와 도기소의 위치가 완전히 삭제되어 있다. 이러한 현상은 첫째, 15세기 중엽 경제적 태평과 함께 백자의 수요 생산이 증가하자 군신의 변별(辨別)과 사치를 이유로 강력하게 규제하여 백자의 확대와 발전에 걸림돌이 되었다. 둘째, 동기(銅器)의 대체품으로 자기를 만들어 충당해야할 강제성 당위성 상실로 인한 자기수요 감소를 초래하였을 것으로 사료된다. 셋째, 경기도 광주에서 백자관요가 운영되었으므로 지방인 상주지역에도 더 이상 백자를 조달받을 필요가 없이, 일반 지방관아와 서민들의 일상용기 생산으로 전락하여 소규모화 되었을 것이라고 사료된다.장 운동기능을 향상시키는 유효성분의 보강 등이 필요하다는 점도 알 수 있었다.더불어 산화물질 해독에 관여하는 다른 유전자

• Elastomers and Composites
• /
• v.35 no.4
• /
• pp.272-280
• /
• 2000

The experimental kinetics was analyzed for commercial rubbers such as NR, IR, BR, SBR 1500, and SBR 1700. Kinetic analysis for the commercial rubbers was performed using a thermogravimetric method, which the activation energies of NR obtained by Kissinger, Friedman, ana Ozawa's method were 195.0, 198.3, and 186.3 kJ/mol, respectively. whereas that of SBR 1500 were 246.4, 247.5, and 254.8 kJ/mol, respectively. It was shown that the yield of pyrolytic oil was generally increased with increasing the final temperature. Considering the effect of heating rate. it was found that the yield of pyrolytic oil was not consistent for each sample. The number average molecular weight of pyrolitic oil of SBR 1500 was in the range of 740-2486. The calorific value of SBR 1500 was 39-40 kJ/g, and it might be a considerable energy potential although it was lower than the conventional fuel such as kerosene, diesel, light fuel, and heavy fuel.

• Elastomers and Composites
• /
• v.34 no.5
• /
• pp.414-422
• /
• 1999

SBR, polyurethane and epoxy latex were separately blended with ethylene-vinyl acetate(EVA) emulsion In $0{\sim}50%$. EVA emulsion was not reacted with latexes in liquid phase and mixtures had good stroage stability. The viscosity of cement mixtures was elevated to 20,000cps in $0.5{\sim}2.0$ hours by mixing. The mixtures mixed with pigment represented high viscosity and showed higher viscosity as time goes by. Mixtures had higher hardness with mixing SBR than mixing epoxy or urethane. The hardness was suddenly increased over cement content 30%. showed pencil hardness $H{\sim}2H$ in $50{\sim}60%$. The increase of hardness in high solids was depended upon not only the condensation of latexs but also the coagulation and adhesion of cement particle.

• Elastomers and Composites
• /
• v.30 no.1
• /
• pp.20-31
• /
• 1995

The purpose of this study is to investigate the reinforcement of inorganic filler silica, treated by MDI about SBR vulcanizate. The characteristics of vulcanization, physical properties, surface properties and dynamic properties were investigated after mixing those silica with SBR and unmodified silica with SBR. In this experiment only the quantity of silica was variable. In the vulcanization characteristics tested by rheometer, S-series showed the fastest scorch $time(t_{10})$ and optimum cure $time(t_{90})$. And in test or tensile characteristics hardness, tensile strength, 100%, 300% modulus and elongation were all appeared in the order of M>S-series. The characteristic bonding of urea between unmodified silica and MDI could be confirmed in IR spectrum. The shapes of silicas treated chemically were observed by SEM. And the dispersion of the filler in the SBR composite was uniform. In the dynamic characteristics by the RDS, the order of elastic modulus G' values was as follows : M>S-series, and also the order of damping values was as follows : M>S-series.

• Elastomers and Composites
• /
• v.27 no.4
• /
• pp.262-266
• /
• 1992

A number of tin-containing elastomers are produced commercially by Korea Kumho Petrochemical Co., Ltd. (KKPC) under the Kosyn Sol tradename. The effect of mastication of commercial and laboratory polymerized S-SBR has, been investigated using chemical mixer(ML-500), NMR, GPC and Mooney viscometer. Mastication of polymers containings coupling bonds is affected by the amount of stearic acid, the temperature of mixing and the time length of mixing.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.1133-1138
• /
• 2000

The interface necessarily exists in joints using cement mortar, UP(Unsaturated Polyester : UP) mortar and SBR(SBR-latex) mortar. Characteristics of shear transfer in joint interface consisting of different materials are studied with experimental and analytical methods. The uniaxial compressive shear experiments are accomplished with various angle of inclination (35, 45, 55, 65, 75°), materials of old and new-cast mortar. In this study, The results are as follows ① Mohr-coulomb's slip theory be applied to the interface consisting different materials ② The cohesion of UP mortar is superior to that f cement mortar, SBR mortar.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.565-572
• /
• 1996

The optimum loading of carbon black was studied for the rubber compounds of natural rubber(NR), butadiene rubber(BR), and styrene-butadiene rubber(SBR) with different amount of oil. The optimum loading of carbon black was determined by the volume ratio of carbon black and L factor of Lee's theory. The optimum loading of carbon black was confirmed by the examination of physical properties of the rubbers. The optimum loading amounts of carbon black for the each rubber compound were 60 phr for NR, 57 phr for BR, 65 phr for SBR-A, 70 phr for SBR-B, and 76 phr for SBR-C, respectively. The optimum loading of carbon black was increased by 5 phr for every increment of 20 phr of oil content. It was revealed that the optimum loading amount of carbon black determined by L factor is closely related to the tensile strength of the rubber compounds. The optimum loading amount of carbon black was observed at the amount which shows the maximum value of tensile strength.

• Elastomers and Composites
• /
• v.42 no.1
• /
• pp.9-19
• /
• 2007

In this study, SBR (Styrene-butadiene rubber: solid content: 25 wt%) nanocomposites reinforced with carbon/organoclay(C18-MMT) were manufactured by a latex method. The SBR nanocomposites was made with the dual phase fillers. The mixing ratios, i.e. carbon black/C18-MMT, were 50/0, 49/1, 48/2, 47/3, 45/5, 44/6, 40/10. Total filler content of compounds was restricted to 50 phr. Cure characteristics and mechanical properties of SBR nanocomposites with carbon black and C18-MMT were evaluated. The SBR nanocomposites containing 49/1 ratio of carbon black/C18-MMT showed good dispersity and excellent values of ODR torque, tensile strength, modulus and tear energy. It was found that the improvement of the mechanical properties was mainly due to the reinforcing effect, i.e., the improvement of dispersion of silicates in the rubber matrix.