• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.12-12
• /
• 1993

95년 발사 예정인 무궁화위성의 궤도전이에 필요한 조정 파라미터를 계산하기 위해 원지점 모터 점화 계획 S/W를 만들어서 결과에 대해 분석해 보았다. S/W는 Mission analysis mode와 Insert mode로 구성되는데, Mission analysis mode에서는 표류궤도를 얻기 위한 점화 파라미터를 구하는 것이고, Insert mode에서는 점화 파라미터를 이용해 표류궤도를 구하는 것이다.

• Smart Structures and Systems
• /
• 제17권3호
• /
• pp.471-489
• /
• 2016

Modal identification based on ambient vibration data has attracted extensive attention in the past few decades. Since the excitation for ambient vibration tests is mainly from the environmental effects such as wind and traffic loading and no artificial excitation is applied, the signal to noise (s/n) ratio of the data acquired plays an important role in mode identifiability. Under ambient vibration conditions, certain modes may not be identifiable due to a low s/n ratio. This paper presents a study on the mode identifiability of an instrumented cable-stayed bridge with the use of acceleration response data measured by a long-term structural health monitoring system. A recently developed fast Bayesian FFT method is utilized to perform output-only modal identification. In addition to identifying the most probable values (MPVs) of modal parameters, the associated posterior uncertainties can be obtained by this method. Likewise, the power spectral density of modal force can be identified, and thus it is possible to obtain the modal s/n ratio. This provides an efficient way to investigate the mode identifiability. Three groups of data are utilized in this study: the first one is 10 data sets including six collected under normal wind conditions and four collected during typhoons; the second one is three data sets with wind speeds of about 7.5 m/s; and the third one is some blind data. The first two groups of data are used to perform ambient modal identification and help to estimate a critical value of the s/n ratio above which the deficient mode is identifiable, while the third group of data is used to perform verification. A couple of fundamental modes are identified, including the ones in the vertical and transverse directions respectively and coupled in both directions. The uncertainty and s/n ratio of the deficient mode are investigated and discussed. A critical value of the modal s/n ratio is suggested to evaluate the mode identifiability of the deficient mode. The work presented in this paper could provide a base for the vibration-based condition assessment in future.

• 한국전자파학회논문지
• /
• 제28권12호
• /
• pp.964-973
• /
• 2017

본 연구는 공통모드 초크의 기생 성분이 공통모드와 차동모드에 미치는 영향을 광대역에서 분석하고, 간단한 고주파 모델링 방법을 제시한다. 공통모드와 차동모드의 2-port 회로망을 각각 구성하여 각 모드에서의 S-parameter를 Network Analyzer로 측정하였다. 측정 결과로부터 등가회로 소자를 추출하여 고주파 등가회로를 모델링하고, 측정치와 시뮬레이션 결과를 비교함으로써 타당성을 검증하였다. 이는 정확하고 예측 가능한 EMI 필터를 설계하는데 적용될 수 있다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 학술대회
• /
• pp.50-56
• /
• 2008

본 논문에서는 실린더 주위유동의 B-mode에 해당하는 레이놀즈 수 300${\sim}$1000범위에서 고차 고해상도기법(OHOC Scheme)을 이용하여 원형 실린더 주위의 유동장 및 음향장 특성에 대해서 연구하였다. B-mode 레이놀즈 수 범위에서 스팬방향 길이에 따른 3차원 원형실린더의 스트롤 수, 양 항력계수의 상관관계에 대해 수치계산 및 실험 결과와 비교 분석한 결과 매우 잘 일치하는 것을 보였다. 그리고 이 결과를 토대로 하여 B-mode 불안정성 영역에서 보다 정확한 2차 와류 모사를 위한 적절한 스팬방향을 찾고, 3차원 후류유동의 불안정성이 음향장의 변화에 미치는 영향을 정성적으로 고찰하여, 3차원 원형실린더의 공력소음 대한 기초적인 연구를 수행하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년 추계학술대회논문집
• /
• pp.50-56
• /
• 2008

본 논문에서는 실린더 주위유동의 B-mode에 해당하는 레이놀즈 수 $300{\sim}1000$범위에서 고차 고해상도 기법(OHOC Scheme)을 이용하여 원형 실린더 주위의 유동장 및 음향장 특성에 대해서 연구하였다. B-mode 레이놀즈 수 범위에서 스팬방향 길이에 따른 3차원 원형실린더의 스트롤 수, 양 항력계수의 상관관계에 대해 수치계산 및 실험 결과와 비교 분석한 결과 매우 잘 일치하는 것을 보였다. 그리고 이 결과를 토대로 하여 B-mode 불안정성 영역에서 보다 정확한 2차 와류 모사를 위한 적절한 스팬방향을 찾고, 3차원 후류유동의 불안정성이 음향장의 변화에 미치는 영향을 정성적으로 고찰하여, 3차원 원형실린더의 공력소음 대한 기초적인 연구를 수행하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.839-843
• /
• 2008

Receiving room's floor impact sound level is been influenced to various factor of slab thickness, room size, structure etc. This study examined the noise of upper part slab and room mode in receiving room to be importance factor that influence in receiving room level among this factors. According to this study, vibration mode in slab and room mode are concentrated on frequency that is high level relatively. This causes bad effect in floor impact sound level. Therefore, method to reduce floor impact sound level is to change vibration mode using slab upper part's resilient material or reduce room mode in receiving room.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.493-498
• /
• 2004

The EMI noise source in a switching mode power supply is dominated by a common mode noise. If we can understand the common mode noise occurring mechanism, it is resulted to find out the method to suppress the EMI noise source in the switching mode power supply. The common mode noise is occurring mostly due to circuit is unbalanced which is caused by the capacitive coupling to frame ground, which passes through a heatsink of the switching devices. This research paper presents a new effective balancing method of buck converter circuit by mean of grounding the parasitic and compensation capacitors in correct proportion which is called that the common mode impedance balance (CMIB). The CMIB can be achieved by source, transmission line and termination balanced, such balancing, the common mode current will be cancelled out in the frame ground. The greatly reduced common mode noise can be confirmed by the experimental results.

• 소성∙가공
• /
• 제19권4호
• /
• pp.236-241
• /
• 2010

The frictional behavior of bare steel sheet highly depends on surface roughness. It was investigated that the change of surface roughness of bare steel sheet due to deformation for each forming mode. The flat type friction test was done to check the effect of surface roughness change on frictional characteristics of bare steel sheet. As increasing the deformation, the Ra value was increased at stretching forming mode and drawing forming mode, however the change of Pc showed different trends. The Pc was decreased as increasing stretch deformation but increased at compression deformation. At drawing forming mode, the friction coefficient was increased as deformation was increased after initial big drop with drawing oil. As deformation was increased, the friction coefficient was decreased with drawing oil at stretching forming mode. The results show that the deformation changes the surface roughness and frictional characteristics of steel sheet but the effect depends on the forming mode.

• Structural Engineering and Mechanics
• /
• 제36권6호
• /
• pp.697-714
• /
• 2010

This paper presents an improved version of the Hilbert-Huang transform (HHT) for the modal evaluation of structural systems or signals. In this improved HHT, a well-designed bandpass filter is used as preprocessing to separate and determine each mode of the signal for solving the inherent modemixing problem in HHT (i.e., empirical mode decomposition, EMD, associated with the Hilbert transform). A screening process is then applied to remove undesired intrinsic mode functions (IMFs) derived from the EMD of the signal's mode. A "best" IMF is selected in each screening process that utilizes the orthogonalization coefficient between the signal's mode and its IMFs. Through mode-by-mode signal filtering, parameters such as the modal frequency can be evaluated accurately when compared to the theoretical value. Time history of the identified modal frequency is available. Numerical results prove the efficiency of the proposed approach, showing relative errors 1.40%, 2.06%, and 1.46%, respectively, for the test cases of a benchmark structure in the lab, a simulated time-varying structural system, and of a linear superimposed cosine waves.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.245-248
• /
• 1997

The control modes used in teleoperation are position control mode, and rate control mode. This paper presents the problems of the conventional control modes, through simulation, proposes an intelligent mixed control mode that converts the operation mode between the position mode and the rate mode intelligently by judging the operator's intention using the real-time measurement data. The effectiveness of the proposed intelligent mixed control mode is demonstrated and compared to other typical control modes through simulation and actual experiment.