• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• Applied Biological Chemistry
• /
• 제21권3호
• /
• pp.150-184
• /
• 1978

합성배지(合成培地)에서 느타리 버섯균(菌)의 균사생육(菌絲生育)과 자실체형성(子實體形成)에 대한 영양적(營養的) 특성(特性)과 생리화학적(生理化學的) 제성질(諸性質)을 구명(究明)하고 볏짚과 톱밥 양(兩) 배지(培地)에서 느타리 버섯의 대량(大量) 생산(生産)을 위한 배양조건(培養條件)을 밝히고, 느타리 버섯 재배기간(栽培期間) 중 배지(培地)와 버섯중의 각종(各種) 성분(成分)의 추이(推移)를 알고자 실험을 수행하여 다음과 같은 결과를 얻었다. 1. 탄소원(炭素源) 중 mannitol과 서은 균사생육(菌絲生育)과 자실체(子實體) 형성(形成)이 빠르고 자실체(子實體)의 수량(收量)이 많았으나 lactose와 rhamnose는 균사(菌絲) 조차도 생육하지 못하였다. 또한 구연산, 호박산, ethyl alcohol 및 glycerol에서는 자실체(子實體) 형성(形成)이 매우 빈약(貧弱)하였고, 식초산, 개미산, 푸마르산, n-butyl alcohol, iso-butyl alcohol 및 n-propyl alcohol은 균사생육(菌絲生育)을 저해(阻害)하였다. 2. 질소원(窒素源)중 peptone은 균사생육(菌絲生育)과 자실체(子實體) 형성(形成)이 빠르고 자실체(子實體)의 수량(收量)이 많았으나 DL-alanine, asparagine, L-aspartic acid, glycine및 serine은 자실체형성(子實體形成)이 매우 빈약(貧弱)하였으며 아질산태질소(亞窒酸態窒素), L-tryptophan 및 L-tyrosine은 균(菌)의 생육을 저해(沮害)하였다. 또한 peptone에 무기태질소(無機態窒素)와 아미노산(酸)을 혼용(混用)한 결과 $(NH_4)_2SO_4$, $NH_4$-tartarate, DL-alanine및 L-leucine에서는 자실체(子實體)의 수량(收量)이 약 10% 증가되었고, L-aspartic acid는 약 15%. L-arginine은 약20%, L-glutamic acid와 L-lysine은 약 25%증가 되었다. 3. C/N율(率) 15.23에서 자실체(子實體) 형성(形成)은 빠르나 자실체(子實體)의 수량(收量)은 감소(減少)되었으며, C/N율(率) 11.42에서는 자실체형성(子實體形成)은 늦으나 자실체(子實體)의 수량(收量)은 증가되는 경향이 있었다. 또한 동일 C/N율(率)에서도 mannitol과 peptone의 농도(濃度)가 높은 편이 수량(收量)이 증가되었다. 그러므로 자실체(子實體)의 수량(收量)과 자실체형성(子實體形成) 소요일(所要日)의 관점(觀點)에서 보면 C/N율(率) 30.46이 어느정도 적당(適當)한 것 같다. 4. Thiamine $50{\mu}g%,\;KH_2PO_4$ 0.2%, $MgSO_4{\cdot}7H_2O$는 $0.02{\sim}0.03%$일때 균사(菌絲)와 자실체(子實體) 생육(生育)이 우수(優秀)하였으며 미량원소(微量元素)로서는 $FeSO_4{\cdot}7H_2O$,\;ZnSO_4{\cdot}7H_2O$ 및 $MnSO_4{\cdot}5H_2O$가 공존(共存)하면 생육촉진(生育促進)의 상승효과(相乘效果)가 인정되었으나 3이원소(元素)중 Mn이 결핍(缺乏)하면 균사(菌絲)와 자실체(子實體)의 생육(生育)이 다소 저하되었다. 이들 염류(鹽類)의 최적농도(最適濃度)는 각각 0.02mg%이었다. 5. Cytosine $0.2{\sim}1mg%$와 indole acetic acid 0.01mg%에서 균사량(菌絲量)은 증가되었으나 자실체(子實體)의 수량(收量)에는 효과 없었으며 그밖의 purine염기(鹽基), pyrimidine염기(鹽基) 및 식물(植物) hormone은 영향이 없었다. 6. 광조사(光照射영)에 의해서 균사생육(菌絲生育)은 저해(沮害)되었으며 영양생장(營養生長)의 후기에 광(光)을 조사(照射)하면 원기형성(原基形成)이 유도(誘導)되었다. 광(光)의 최적조도(最適照度)는 $100{\sim}500lux$, 조사시간(照射時間)은 매일 $6{\sim}12$시간이었고, 이 이상(以上)의 조도(照度)에서는 오히려 저해(沮害)되었으며, 암소(暗所)에서는 원기(原基)가 형성(形成)되지 않고 영양생장(營養生長)만 계속되었다. 7. 균사생육(菌絲生育)과 자실체(子實體) 형성(形成)의 최적온도(最適溫度)는 각각 $25^{\circ}C,\;10{\sim}15^{\circ}C$이었고 최적(最適)의 pH범위(範圍)는 $5.0{\sim}6.5$이었으며 균사(菌絲)는 $7{s\im}10$일간 배양(培養)했을 때가 자실체(子實體) 형성(形成)이 제일 우수(優秀)하였다. 또한 배지량(培地量)이 적을수록 자실체(子實體) 형성(形成)은 빠르나 자실체(子實體)의 수량(收量)은 감소(減少)되었고 배지량(培地量)이 많을수록 자실체(子實體) 형성(形成)은 늦은반면에 그 수량(收量)은 증가 되었으며, 원기형성(原基形成)은 $CO_2$에 의하여 저해(沮害)되었다. 8. 볏짚과 톱밥 병 배지(培地)에서 균사생육(菌絲生育)의 최적(最適) 수분량(水分量)은 70%이상 이었으며 미강(米糠) 10%를 배지(培地)에 첨가(添加)했을 때는 균사생육(菌絲生育)과 자실체형성(子實體形成)이 우수(優秀)하였다. 그리고 양배지(兩培地)에 $CaCo_3$를 단독(單獨)으로 첨가했을 때는 유효(有？)하였으나 미강(米糠)과 함께 첨가했을때는 효과(？果)를 볼 수 없었다. 9. 재배(栽培) 실험(實驗)에서 느타리 버섯의 전체(全體) 수량(收量)은 볏짚배지(培地)에서 $14.99kg/m^2$, 톱밥배지(培地)에서 $6.52kg/m^2$이었고 양배지(兩培地) 모두 90%이상이 1,2주기(週期)에서 얻어졌으며 볏짚배지(培地)(dry matter $20.96kg/m^2$)의 전수율(全收率)을 톱밥배지(培地)(dry matter $20.83kg/m^2$)의 약 2.3배(倍)이었다. 10. 재배기간(栽培期間)중 양(兩) 배지(培地)의 일반 성분을 고형물(固形物) 기준(基準)으로 볼때 회분(灰分)의 변화는 적었으나 유기물(有機物)은 감소(減少)되었으며, 수분(水分)은 종균접종시(種菌接種時) 약 79%이던것이 균사번식기간(菌絲繁殖期間)중에 다소 감소(減少)되었고 그 이후부터는 큰 변화가 없었다. 11, 종균접종시(種菌接種時) 부터 4주기(週期) 수확(收穫) 후까지 배지(培地) 성분(成分)의 소실(消失)을 보면 볏짚배지(培地)는 고형물(固形物) 약 19.7%, 유기물(有機物) 약 19.3%, 질소(窒素) 약 40%가 소실(消失)되었으며, 톱밥 배지(培地)에서는 고형물(固形物) 약 7.5%, 유기물(有機物) 약 7.6%, 질소(窒素) 약 20%가 소실(消失)되었다. 버섯 1kg을 생산(生産)하기 위하여 볏짚 배지(培地)에서는 유기물(有機物) 약 232g, 질소(窒素) 약 7.0g이 소실(消失)되었고, 톱밥 배지(培地)에서는 유기물(有機物) 약 235g, 질소(窒素) 약 6.8g이 소실(消失)되었으며, 버섯 1kg당(當) 함유된 유기물(有機物)은 각각 82.4g, 82.3g, 질소(窒素)는 각각 5.6g, 5.4g이었다. 12. 양배지(兩培地)의 전질소(全窒素)는 점차적으로 감소(減少)되었고 불용성질소(不溶性窒素)의 절대감소량(絶對減少量)은 수용성질소(水溶性窒素)보다 컸으며 아미노태(態) 질소(窒素)는 3주기(週期)까지는 계속 증가 되었으나 그 이후부터는 감소(減少)되었다. 13. 볏짚 배지(培地)에서는 재배기간(栽培其間)에 소실(消失)된 전(全) pentosan의 28%, ${\alpha}$-cellulose는 13.8%가 균사생육(菌絲生育)중에 소실(消失)되었고 톱밥배지(培地)에서는 전(全) pentosan의 24.1%, ${\alpha}$-cellulose는 11.9%가 소실(消失)되었으며 lignin은 양(兩) 배지(培地)의 2주기(週期) 수확(收穫)부터 다소 감소(減少)되었다. 환원당(還元糖), trehalose 및 mannitol은 계속 증가의 추세를 보였으며 C/N율(率)은 볏짚 배지(培地)에서 종균(種菌) 접종시(接種時) 33.2이었던 것이 폐상시(廢床時)에는 30.3이었고, 톱밥 배지(培地)는 61.3이었던 것이 60.0 이었다. 14. 양(兩) 배지(培地)에서 P, K, Mn, Zn은 감소(減少)되었고, Mg, Ca, Cu는 불규칙하게 변화되었으며, Fe는 증가되는 경향이었다. 15. 재배기간(栽培期間)중 각종효소(各種酵素)의 활성(活性)은 톱밥배지(培地)보다 볏짚배지(培地)가 월등히 높았다. 즉 CMC 당화활성(糖化活性)과 CMC액화활성(液化活性)은 균사번식(菌絲繁殖)후부터 2주기수확(週期收穫)까지는 양배지(兩培地)에서 점차적으로 증가 되었으나 그 이후부터는 감소(減少)되었다. xylanase활성(活性)은 1주기(週期)보다 2주기(週期)에서 급격히 상승되었고 3주기(週期)가 되면서 볏짚 배지(培地)에서는 신속히 감소(減少)되었으나 톱밥 배지(培地)에서는 이와같은 감소(減少)를 볼 수 없었다. protease 활성(活性)은 균사번식(菌絲繁殖)후 최고의 활성도(活性度)를 보였다가 점차로 감소(減少)하였다. 또한 볏짚 배지(培地)의 pH는 종균접종시(種菌接種時) 6.3이던 것이 4주기(週期)후는 5.0이었고 톱밥배지(培地)의 pH는 5.7에서 4.9로 떨어졌다. 16. 볏짚 배지(培地)에서 생육한 버섯은 섬유소(纖維素)를 제외한 모든 성분량(成分量)이 톱밥배지(培地)에서 생육한 버섯보다 높은 경향이있었으며 양배지(兩培地)에서 버섯의 각주기별(各週期別) 성분(成分) 변화는 $1{\sim}3$주기(週期)까지는 거의 비슷하였으나 4주기(週期)에서는 다소 감소(減少)의 추세를 보였다.

• Journal of Preventive Medicine and Public Health
• /
• 제7권1호
• /
• pp.29-94
• /
• 1974

Today most developed countries provide modern medical care for most of the population. The rural area is the more neglected area in the medical and health field. In public health, the philosophy is that medical care for in maintenance of health is a basic right of man; it should not be discriminated against racial, environmental or financial situations. The deficiency of the medical care system, cultural bias, economic development, and ignorance of the residents about health care brought about the shortage of medical personnel and facilities on the rural areas. Moreover, medical students and physicians have been taught less about rural health care than about urban health care. Medical care, therefore, is insufficient in terms of health care personnel/and facilities in rural areas. Under such a situation, there is growing concern about the health problems among the rural population. The findings presented in this report are useful measures of the major health problems and even more important, as a guide to planning for improved medical care systems. It is hoped that findings from this study will be useful to those responsible for improving the delivery of health service for the rural population. Objectives: -to determine the health status of the residents in the rural areas. -to assess the rural population's needs in terms of health and medical care. -to make recommendations concerning improvement in the delivery of health and medical care for the rural population. Procedures: For the sampling design, the ideal would be to sample according to the proportion of the composition age-groups. As the health problems would be different by group, the sample was divided into 10 different age-groups. If the sample were allocated by proportion of composition of each age group, some age groups would be too small to estimate the health problem. The sample size of each age-group population was 100 people/age-groups. Personal interviews were conducted by specially trained medical students. The interviews dealt at length with current health status, medical care problems, utilization of medical services, medical cost paid for medical care and attitudes toward health. In addition, more information was gained from the public health field, including environmental sanitation, maternal and child health, family planning, tuberculosis control, and dental health. The sample Sample size was one fourth of total population: 1,438 The aged 10-14 years showed the largest number of 254 and the aged under one year was the smallest number of 81. Participation in examination Examination sessions usually were held in the morning every Tuesday, Wenesday, and Thursday for 3 hours at each session at the Namchun Health station. In general, the rate of participation in medical examination was low especially in ages between 10-19 years old. The highest rate of participation among are groups was the under one year age-group by 100 percent. The lowest use rate as low as 3% of those in the age-groups 10-19 years who are attending junior and senior high school in Taegu city so the time was not convenient for them to recieve examinations. Among the over 20 years old group, the rate of participation of female was higher than that of males. The results are as follows: A. Publie health problems Population: The number of pre-school age group who required child health was 724, among them infants numbered 96. Number of eligible women aged 15-44 years was 1,279, and women with husband who need maternal health numbered 700. The age-group of 65 years or older was 201 needed more health care and 65 of them had disabilities. (Table 2). Environmental sanitation: Seventy-nine percent of the residents relied upon well water as a primary source of dringking water. Ninety-three percent of the drinking water supply was rated as unfited quality for drinking. More than 90% of latrines were unhygienic, in structure design and sanitation (Table 15). Maternal and child health: Maternal health Average number of pregnancies of eligible women was 4 times. There was almost no pre- and post-natal care. Pregnancy wastage Still births was 33 per 1,000 live births. Spontaneous abortion was 156 per 1,000 live births. Induced abortion was 137 per 1,000 live births. Delivery condition More than 90 percent of deliveries were conducted at home. Attendants at last delivery were laymen by 76% and delivery without attendants was 14%. The rate of non-sterilized scissors as an instrument used to cut the umbilical cord was as high as 54% and of sickles was 14%. The rate of difficult delivery counted for 3%. Maternal death rate estimates about 35 per 10,000 live births. Child health Consultation rate for child health was almost non existant. In general, vaccination rate of children was low; vaccination rates for children aged 0-5 years with BCG and small pox were 34 and 28 percent respectively. The rate of vaccination with DPT and Polio were 23 and 25% respectively but the rate of the complete three injections were as low as 5 and 3% respectively. The number of dead children was 280 per 1,000 living children. Infants death rate was 45 per 1,000 live births (Table 16), Family planning: Approval rate of married women for family planning was as high as 86%. The rate of experiences of contraception in the past was 51%. The current rate of contraception was 37%. Willingness to use contraception in the future was as high as 86% (Table 17). Tuberculosis control: Number of registration patients at the health center currently was 25. The number indicates one eighth of estimate number of tuberculosis in the area. Number of discharged cases in the past accounted for 79 which showed 50% of active cases when discharged time. Rate of complete treatment among reasons of discharge in the past as low as 28%. There needs to be a follow up observation of the discharged cases (Table 18). Dental problems: More than 50% of the total population have at least one or more dental problems. (Table 19) B. Medical care problems Incidence rate: 1. In one month Incidence rate of medical care problems during one month was 19.6 percent. Among these health problems which required rest at home were 11.8 percent. The estimated number of patients in the total population is 1,206. The health problems reported most frequently in interviews during one month are: GI trouble, respiratory disease, neuralgia, skin disease, and communicable disease-in that order, The rate of health problems by age groups was highest in the 1-4 age group and in the 60 years or over age group, the lowest rate was the 10-14 year age group. In general, 0-29 year age group except the 1-4 year age group was low incidence rate. After 30 years old the rate of health problems increases gradually with aging. Eighty-three percent of health problems that occured during one month were solved by primary medical care procedures. Seventeen percent of health problems needed secondary care. Days rested at home because of illness during one month were 0.7 days per interviewee and 8days per patient and it accounts for 2,161 days for the total productive population in the area. (Table 20) 2. In a year The incidence rate of medical care problems during a year was 74.8%, among them health problems which required rest at home was 37 percent. Estimated number of patients in the total population during a year was 4,600. The health problems that occured most frequently among the interviewees during a year were: Cold (30%), GI trouble (18), respiratory disease (11), anemia (10), diarrhea (10), neuralgia (10), parasite disease (9), ENT (7), skin (7), headache (7), trauma (4), communicable disease (3), and circulatory disease (3) -in that order. The rate of health problems by age groups was highest in the infants group, thereafter the rate decreased gradually until the age 15-19 year age group which showed the lowest, and then the rate increased gradually with aging. Eighty-seven percent of health problems during a year were solved by primary medical care. Thirteen percent of them needed secondary medical care procedures. Days rested at home because of illness during a year were 16 days per interviewee and 44 days per patient and it accounted for 57,335 days lost among productive age group in the area (Table 21). Among those given medical examination, the conditions observed most frequently were respiratory disease, GI trouble, parasite disease, neuralgia, skin disease, trauma, tuberculosis, anemia, chronic obstructive lung disease, eye disorders-in that order (Table 22). The main health problems required secondary medical care are as fellows: (previous page). Utilization of medical care (treatment) The rate of treatment by various medical facilities for all health problems during one month was 73 percent. The rate of receiving of medical care of those who have health problems which required rest at home was 52% while the rate of those who have health problems which did not required rest was 61 percent (Table 23). The rate of receiving of medical care for all health problems during a year was 67 percent. The rate of receiving of medical care of those who have health problems which required rest at home was 82 percent while the rate of those who have health problems which did not required rest was as low as 53 percent (Table 24). Types of medical facilitied used were as follows: Hospital and clinics: 32-35% Herb clinics: 9-10% Drugstore: 53-58% Hospitalization Rate of hospitalization was 1.7% and the estimate number of hospitalizations among the total population during a year will be 107 persons (Table 25). Medical cost: Average medical cost per person during one month and a year were 171 and 2,800 won respectively. Average medical cost per patient during one month and a year were 1,109 and 3,740 won respectively. Average cost per household during a year was 15,800 won (Table 26, 27). Solution measures for health and medical care problems in rural area: A. Health problems which could be solved by paramedical workers such as nurses, midwives and aid nurses etc. are as follows: 1. Improvement of environmental sanitation 2. MCH except medical care problems 3. Family planning except surgical intervention 4. Tuberculosis control except diagnosis and prescription 5. Dental care except operational intervention 6. Health education for residents for improvement of utilization of medical facilities and early diagnosis etc. B. Medical care problems 1. Eighty-five percent of health problems could be solved by primary care procedures by general practitioners. 2. Fifteen percent of health problems need secondary medical procedures by a specialist. C. Medical cost Concidering the economic situation in rural area the amount of 2,062 won per residents during a year will be burdensome, so financial assistance is needed gorvernment to solve health and medical care problems for rural people.

• 한국산림과학회지
• /
• 제54권1호
• /
• pp.1-24
• /
• 1981

강원도(江原道)는 관광자원(觀光資源)이 풍부(豊富)하며 태백산맥(太白山脈)을 중심(中心)으로한 산악관광권(山岳觀光圈), 동해안(東海岸)의 해안관광권(海岸觀光圈), 내륙(內陸)의 호수관광권(湖水觀光圈)으로 구분(區分)하고 있다. 동해(東海)의 절경(絶景)을 배경(背景)으로 설악산(雪岳山)과 오태산(五台山)의 국립공원(國立公園)이 있다. 그리고 치악산(雉岳山)의 도립공원(道立公園)이 있다. 북한강상류수계(北漢江上流水系)에는 발전용(發電用)댐건설(建設)로 만수(滿水)된 인공호수(人工湖水)가 연좌(連坐)하고 있어 호수관광권(湖水觀光圈)으로 각광(脚光)을 받고 있다. 본(本) 논문(論文)에서도 강원도행정수도(江原道行政首都)이며 호반(湖畔)의 도시(都市)인 춘천(春川)을 중심(中心)으로 북한강상류수계(北漢江上流水系)에 연좌(連坐)하고 있는 호수단지주변(湖水團地周邊)의 관광자원(觀光資源)을 배경(背景)으로 하여 삼림(森林)의 풍경적시업방안(風景的施業方案)을 모색하고 있다. 본(本) 호수단지(湖水團地)는 하류(下流)로부터 상류(上流)로 향(向)하여 의암호(衣岩湖), 소양호(昭陽湖), 춘천호(春川湖), 파려호(破慮湖)가 자리잡고 있으며 이들 4개(個) 호수(湖水)의 면적(面積)은 $140.4km^2$ 총저수량(總貯水量)은 4,155백만(百萬)$m^3$이다. 그리고 발전량(發電量)은 41만(萬)KW의 시설(施設)을 갖추고 있다. 이들 호수(湖水)를 위적(囲績)하고 있는 삼림면적(森林面積)은 $1,208km^2$에 달(達)한다. 삼림(森林)은 행정적(行政的)으로 시업림(施業林)$745km^2$와 시업제한림(施業制限林) $463km^2$로 구분(區分)하고 있으며 시업제한림(施業制限林)은 개발제한구역(開發制限區域)과 자연환경보전지구내(自然環境保全地區內)에 있는 삼림(森林)과 보안림(保安林)으로 되어 있다. 개발제한구역내(開發制限區域內)에 있는 삼림(森林)은 춘천(春川)을 중심(中心)으로 반경(半徑) 10km이내(以內)에 있는 의암호주변삼림(衣岩湖周邊森林)이며 그 면적(面積)은 $177km^2$이다. 자연환경보전지구내(自然環境保全地區內)의 삼림(森林)은 소양호연안(昭陽湖沿岸)에서 2km의 가시권내(可視圈內)에 설정(設定)되어 있으며 그 면적(面積)은 $165km^2$이다. 보안림(保安林)은 각(各) 호수연안삼림(湖水沿岸森林)에 설정(設定)되어 있으며 입지적여건상(立地的與件上) 수원함양림(水源函養林)이 주종(主宗)이며 그 면적(面積)은 $121km^2$이다. 본(本) 호수단지권내(湖水團地圈內)에는 많은 각승지(各勝地)와 유원지(遊園地) 그리고 문화재(文化財)와 유적지(遺蹟地)가 있어 호수(湖水)와 삼림(森林)과 같이 귀중(貴重)한 관광자원(觀光資源)으로 부상(浮上)되고 있다. 본(本) 호수단지주변삼림(湖水團地周邊森林)은 I~II영급(令級)의 유령림(幼令林)이 전체삼림(全體森林)의 70%를 점(點)하고 있어 ha당(當)축적(蓄積)은 $15m^3$로 탐약(貪弱)하다. 침엽수림(針葉樹林), 활엽수림(濶葉樹林), 혼효림(混淆林)의 면적비율(面積比率)은 35:37:28로 활엽수림(濶葉樹林)의 면적(面積)이 약천(若千) 우위(優位)를 점(點)하고 있다. 소유형태(所有形態)는 국유림(國有林), 도유림(道有林), 군유림(郡有林), 사유림(私有林)으로 되어 있으며 그 비율(比率)은 36:14:5:45로 사유림(私有林)이 약절반(約切半)을 점(點)하고 다음이 국유림(國有林), 도유림(道有林), 군유림(郡有林)의 순(順)으로 되어 있다. 지질(地質)은 모암(母岩)이 화강암(花岡岩) 또는 편마암계(片麻岩系)로서 풍화성(風化性)이 강(强)하고 표토층(表土層)이 척박(瘠薄)함으로 임지비배문제(林地肥培問題)를 염두(念頭)에 두어야 한다. 이상(以上)의 여건(與件)을 토태(土台)로 삼림(森林)의 풍경적시업(風景的施業)의 기본방향(基本方向)을 제시(提示)하면 다음과 같다. 1) 현재(現在) 임분(林分)은 유령림(幼令林)이 대부분(大部分)이고 임지(林地)가 척박(瘠薄)함으로 임지비배(林地肥培)와 임목무육(林木撫育)에 주력(注力)하여 장령림(壯令林)의 경지(境地)로 유도(誘導)할 것. 2) 황폐성미립목지(荒廢性未立木地)와 임간라지(林間裸地)에는 속성수(速成樹)인 리기다소나무, 오리나무 등(等)은 식재(植栽)하여 조속(早速)히 피복녹화(被覆綠化) 시킬 것. 3)계곡부(溪谷部)로서 습윤(濕潤)하고 지미(地味)가 비교적(比較的) 양호(良好)한 라지(裸地)에는 잣나무, 낙엽송, 전나무 등(等)을 식재(植栽)하여 교림(喬林)으로 육성(育成)할 것. 4) 현재(現在) 사유림(私有林)의 침엽수림(針葉樹林)은 적송(赤松)이 주체(主體)가 되어 있다. 적송(赤松)은 양수(陽樹)로서 수원함양기능(水源函養機能)이 적은 위에 현재(現在) 솔잎혹파리의 피해(被害)를 입고 있어 수종갱신(樹種更新)이 불가피(不可避)하다. 그러므로 계곡부(溪谷部)부터 잣나무, 전나무, 가문비나무, 솔송나무 등(等)을 식재(植栽)하에 점차(漸次) 음성(陰性) 침엽수림(針葉樹林)으로 대체(代替)케 할 것. 5) 현재(現在) 활엽수림(濶葉樹林)은 재질면(材質面)에 있어서나 풍치면(風致面)에 있어서 가치성(價値性)이 저렬(低劣)한 잡목(雜木), 관목(灌木) 등(等)이 많으므로 점차(漸次) 이를 제거(除去)하고 참나무, 단풍나무, 물푸레나무, 자작나무, 가래나무등(等)으로 대체(代替)케 할 것. 6) 주변(周邊) 산록부(山麓部)에는 벚나무, 수양버들, 은사시나무, 후박나무, 은행나무, 향나무, 밤나무, 살구나무, 등(等)의 관상수(觀賞樹)를 조화(調和)있게 식재(殖財)할 것. 7) 활엽수림(濶葉樹林)의 갱신(更新)을 중림형(中林型)으로 유도(誘導)하여 상하이단(上下二段)의 임관형(林冠型)의 미(美)를 조성(造成)하는 구역(區域)과 왜림형(矮林型)을 조리(調利)있게 배열(配列)하는 방안(方案)을 모색할 것. 8) 침엽수림(針葉樹林)의 갱신(更新)은 택벌작업(擇伐作業) 또는 산벌작업(傘伐作業)에 의(依)해 풍치보전(風致保全)을 기(期)할 것. 9) 혼효림(混淆林)은 상목(上木)은 침엽수(針葉樹)를 하목(下木)은 활엽수(濶葉樹)로 하는 중림형(中林型)의 풍치(風致)를 보존(保存)토록 할 것. 요(要)컨대 호수(湖水)의 우아(優雅)한 여성미(女性美)와 삼림(森林)의 호장웅대(豪壯雄大)한 남성미(男性美)가 조화(調和)되어 자연(自然)의 심오(深奧)한 신비성(神秘性)을 간직하는데 역점(力點)을 두어 궁극적(窮極的)으로는 삼림(森林)을 배경(背景)으로한 호수관광권(湖水觀光圈)의 면모(面貌)를 갖추는데 초점(焦點)을 둘 것이다.

• 한국토양비료학회지
• /
• 제10권3호
• /
• pp.171-188
• /
• 1977

전작물(田作物)에 대(對)한 가리비료(加里肥料)의 효과(效果)를 검토(檢討)하고 그 결과(結果)를 다음과 같이 요약(要約)하였다. 1. 작물(作物)의 종류별(種類別) 가리(加里)의 10a당(當) 평균(平均) 시비적량(施肥適量)은 각각(各各) 목초(牧草) 32, 채소(菜蔬) 22.5, 과수(果樹) 17.3, 서류(薯類) 13.3, 화곡류(禾穀類) 6.5kg이다. 최근(最近) 경제성장(經濟成長)과 더부러 목초(牧草), 채소(菜蔬) 및 과수(果樹)의 재배면적(栽培面積)이 급격(急激)히 증가(增加)하고 있어 영후(令後)의 가리비료(加里肥料) 수요(需要)는 크게 증대(增大)될 것이다. 2. 주요(主要) 전작물(田作物)에 대(對)한 평균(平均) 적정가리(適正加里) 시비량(施肥量)은 보리 6.5, 밀 6.9, 콩 4.5, 옥수수 8.1, 감자 8.9, 고구마 17.7kg/10a이다. 가리성분(加里成分) 1kg/10a당(當) 평균(平均) 증수량(增收量)은 화곡류(禾穀類)에서 4~5kg이고 서류(薯類) 46kg로서 수익성(收益生)은 서류(薯類)에서 높다. 3. 전국(全國)의 치환성(置換性) 가리(加理) 함량(含量)의 분포(分布)는 해안지대(海岸地帶) 특(特)히 남해안(南海岸)에서 높고 내륙지대(內陸地帶)에서 낮으며 산악지대(山岳地帶)는 그 중간(中間)이다. 도별(道別)로는 제주(濟州)>전남(全南)>강원(江原)>경남(慶南)의 순(順)이고 경북도(慶北道)에서 가장 낮다. 대 맥(大 麥) : 4. 월동맥류(越冬麥類에) 대(對)한 가리(加里)의 비효(肥效) 및 적량(適量)은 l차적(次的)으로 기온(氣溫)의 영향(影響)을 받으며 토양인자(土壞因子)는 제(第)2차적(次的)인 것으로 생각할 수 있다. 따라서 토양별(土壞別) 또는 토양검정(土壞檢定)에 따른 시비량(施肥量) 결정기준(決定基準)은 기존지대별(氣候地帶別)로 설정(設定)함이 합리적(合理的)일 것이다. 5. 고온(高溫)에서는 토양(土壞) 중(中)의 가리(加里)의 방출(放出)이 촉진(促進)되어 가리(加里)에서 시용효과(施用效果)와 시비적량(施肥適量)이 남부(南部)에서 적고 저온인 북부(北部)에서 높으나 시비(施肥) 인산(燐酸)은 고온에서 고정(固定)이 촉진(促進)되어 남부(南部)에서 시비적량(施肥適量)이 많으며 질소(窒素)는 온도요인(溫度要因)보다는 강수량(降水量)의 영향이 커서 강수량(降水量)이 많은 남부(南部)에서 시비적량(施肥適量)이 극히 높은 것으로 풀이되었다. 6. 도별(道別) 평균(平均) 가리비효(加里肥效)는 남부(南部)로 갈수록 떨어지는 경향(傾向)을 보였고 경북(慶北)만이 예외적(例外的)으로 높다. 경북(慶北)은 치환성(置換性) 가리함량(加里含量)이 가장 낮을 뿐 아니라 산간지역(山間地域)의 저온권 전작지대(田作地帶)가 많은 것이 원인(原因)인 것 같다. 7. 가리(加里)의 비효(肥效)와 시비적량(施肥適量)은 연차별(年次別) 변이(變異)가 크다. 가리(加里)의 비효(肥效)는 저온의 해에 컸고(평년(平年)의 2~3배(倍)) 조해(早害)와 습해(濕害)가 있었던 해에는 적었으며 시비적량(施肥適量)은 저온으로 동해(凍害)가 있었던 해보다는 조해(早害)와 습해(濕害)가 있었던 해에서 더욱 많다. 8. 모암별(母岩別) 치환성(置換性) 가리(加里) 함량(含量)은 결정편암(結晶片岩)>화강암(花崗岩)>수성암(水成岩)>현무암(玄武岩)의 순(順)이나 가리(加里)의 비효(肥效)는 이와 반대(反對)의 순(順)이어서 모암별(母岩別) 가리(加里) 함량(含量)과 비효간(肥效間)에는 뚜렷한 역상관(逆相關)이 있다. 9. 모재별(母材別) 치환성(置換性) 가리(加里) 함량(含量)은 충적토(沖積土)>잔적토(殘積土)>홍적토(洪積土)>곡간충적토이며 가리비효(加里肥效)는 곡간충적토에서 만이 현저히 클 뿐 그 외(外)의 모재간(母材間)에 는 분명(分明)한 차이(差異)가 없다. 10. 가리(加里)의 비효(肥效)와 적량(積量)은 토성(土性) 차이(差異)에 의(依)하여 크게 달라서 가리비효(加里肥效)는 사질(砂質)쪽에서 높고 가리적량(加里適量)은 식질(埴質) 쪽에서 높다. 특(特)히 사질(砂質)인 양토(壤土)와 사양토(砂壤土)에서는 적량(適量)을 초과(超過) 시비(施肥)했을 때 감수(減收)가 크다. 11. 가리시용(加里施用)에 의(依)해서 평균적(平均的)으로 출수일(出穗日)이 1.7일(日) 지연되고 간장(稈長)은 4.4cm가 증대(增大)되며 주당수수(株當穗數)(0.3)와 1,000립중(粒重) 및 저엽비율(租葉比率)이 증대(增大)된다. 콩 : 12. 콩의 가리비효(加里肥效)는 곡류작물(穀物作物) 중(中)에서 가장 적으나 신개간지(新開墾地)에서는 가리(加里) 8kg/10a 시용(施用)으로 자실중(子實重)이 28kg/10a까지 증수(增收)된다. 13. 모암별(母岩別) 가리비효(加里肥效)는 현무암(玄武岩)제주(濟州)>수성암(水成岩)>화강암(花崗岩) 및 석회암(石灰巖)의 순(順)이며 연차별(年次別) 변이폭(慶異幅)도 크다. 옥수수 : 14. 치환성(置換性) 가리함량(加里含量)이 많은 토양(土壞)에서는 옥수수의 가리비효(加里肥效)는 떨어지나 절대수량(絶對收量)이 높기 때문에 오히려 가리(加里)의 시비적량(施肥適量)은 가리함량(加里含量)이 높은 경우에 높다. 15. 옥수수에 대(對)한 가리비효(加里肥效)는 인산(燐酸)의 시비수준(施肥水準)과 교호작용(交互作用)이 인정(認定)되어 인산(燐酸)의 적량(適量) 시용하(施用下)에서 가리(加里)의 비효(肥效)도 크고 적량(適量)도 높다. 서 류(薯類) : 16. 감자는 가리(加里)보다도 질소(窒素)의 요구량(要求量)이 더 많으며 이 때문에 감자가 스스로 토양가리(土壤加里)의 흡수능력(吸收能力)이 큰 것 같다. 17. 감자의 수량(收量)은 식양토(埴壤土) 보다는 사양토(砂壤土)에서 높고 치환성(置換性) 가리(加里) 함량(含量)이 높을수록 높다. 그러나 가리(加里)의 비효(肥效)는 사질토(砂質土)보다는 식양토(埴壤土)에서 높고 전토양(田土壤)보다는 답토양(畓土壤)과 같은 불량환경(不良環境) 조건(條件)에서 더욱 크다. 18. 고구마에서는 질소(窒素)와 인산(燐酸)의 요구량(要求量)은 비교적 낮고 흡비력(吸肥力)이 강(强)하여 불량토양(不良土壤)에서도 상당히 높은 수량(收量)을 얻을수 있으나 가리(加里)의 시비적량(施肥適量)과 시비효과(施肥效果)가 매우 크다는 것이 특징(特徵)이다. 19. 고구마에 대(對)한 가리(加里)의 시비효과(施肥效果)는 토성별(土性別)로 차이(差異)가 크며 치환성(置換性) 가리(加里) 함량(含量)이 낮은 사질토(砂質土)에서도 충분량(充分量)의 가리(加里)를 시용(施用)했을 때는 비효(肥效)가 크게 나타나 수량(收量)이 토양(壤土) 및 식양토(埴壤土)에 비하여 높아진다. 20. 신개간지(新開墾地)와 같이 척박한 토양(壤土)에서도 충분량(充分量)의 가리(加里)를 시용(施用)했을 때는 숙전(熟田)과 대등(對等)한 수량(收量)을 올릴 수 있다.

• 한국유통학회지:유통연구
• /
• 제15권2호
• /
• pp.1-34
• /
• 2010

소비자의 구매 행위가 합리적이고 실용적인 방향으로 변화하는데 힘입어 할인점업계는 급속한 외형적인 성장과 함께 경쟁도 치열하다. 따라서 업계는 그 해결책으로 차별화와 수익성을 동시에 실현 시킬 수 있는 유통업체 브랜드(PB: Private Brand) 개발에 사활을 걸고 있다. 또한 치열한 경쟁 환경 하에서 생존하기 위해서는 고객만족을 넘어서 고객충성도를 높이는 것이 효과적인 방법임이 밝혀짐에 따라 PB가 고객충성도를 제고시키기 위한 전략적인 도구로 사용되고 있다. PB 이용 고객의 충성도를 높이려면 우선 고객집단의 특성을 파악해서 소비자가 지각하는 품질수준을 우선적으로 맞춰줘야 고객만족과 고객신뢰를 얻을 수 있고 결과적으로 고객충성도로 유도할 수 있다. 이에 본 연구는 지각된 품질에 영향을 미치는 선행요인과 고객충성도에 영향을 미치는 변수들 간의 관계에 대한 체계적인 분석결과를 제시하기 위해 선행연구에서 검증된 인과관계를 기반으로 연구모형과 연구가설을 설정했고, 주요 연구결과는 다음과 같다. 기업명성, 브랜드명성, 제품경험, 브랜드친숙도가 높을수록 지각된 품질이 높아지고, 지각된 품질이 높을수록 고객만족, 고객신뢰, 고객충성도가 높아지며, 고객만족과 고객신뢰가 높을수록 고객충성도가 높아지는 것으로 조사되었다. 또한 기업명성이 지각된 품질에 미치는 영향력은 PB가 NB보다 높게 나타난 반면 브랜드명성과 브랜드친숙도가 지각된 품질에 미치는 영향력은 NB가 PB보다 높게 나타났다. 이러한 실증분석 결과는 지각된 품질에 영향을 미치는 선행요인과 결과요인에 대한 보다 명확한 이해를 바탕으로 실무자가 마케팅 활동을 하는데 유용하게 활용할 수 있을 것이다.

• 한국토양비료학회지
• /
• 제5권2호
• /
• pp.1-38
• /
• 1972

우리나라 답토양(畓土壤)에 대(對)한 토지(土地)의 합리적(合理的) 이용(利用), 토지기반조성(土地基盤造成) 및 생산성 향상(向上) 그리고 토양(土壤)에 관(關)한 조사연구(調査硏究)의 방향(方向)을 뒷받침하기 위(爲)하여 김제만경평야(金堤萬頃平野)에 분포(分布)하고 있는 답토양(畓土壤)에 대(對)한 형태(形態) 및 이화학적(理化學的) 특성(特性) 그리고 그와 수도수량(水稻收量)과의 관계(關係)를 구명(究明)하고 이를 기초(基礎)로 하여 답토양(沓土壤)의 분류법(分類法)과 적성등급구분(適性等級區分)을 시안(試案)하였는 바 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 답토양(畓土壤)의 형태(形態), 이화학적(理化學的) 특성(特性) 및 그와 수도수량(水稻收量)과의 관계(關係) 김제(金堤) 만경평야(萬頃平野)에 분포(分布)하고 있는 15개(個) 답토양통(畓土壤統)에 대(對)하여 이들 토양(土壤)의 형태(形態), 이화학적(理化學的) 특성(特性)을 보면 다음과 같다. 토양단면(土壤斷面)의 발달정도(發達程度)를 보면 공덕(孔德), 김제(金堤), 만경(萬頃), 백구(白鷗), 봉남(鳳南), 부용(芙蓉), 수암(水岩), 전북(全北), 지산(芝山) 및 호남통(湖南統)는 B(Cambic B)층(層)이 있고 극락(極樂)과 화동통(華東統)은 Bt(Argillic B)층(層)이 있으나 광활(廣活), 신답(新踏) 및 화계통(華溪統)에는 B층(層) 혹(或)은 Bt층(層)이 없다. 특(特)히 공덕(孔德) 및 봉남통(鳳南統)은 흑니층(黑尼層)이 심토(心土) 하부(下部)에 개재(介在)되여 있다. 토양단면(土壤斷面)의 토색(土色)을 보면 공덕(孔德), 광활(廣活), 백구(白鷗) 및 신답통(新踏統)은 대체(大體)로 청회색(靑灰色), 암회색(暗灰色)을 띄우고 김제(金堤), 만경(萬頃), 봉남(鳳南), 부용(芙蓉), 수암(水岩), 전북(全北), 지산(芝山) 및 호남통(湖南統)은 회색(灰色), 회갈색(灰褐色)을 띠우며 극락(極樂), 화계(華溪) 및 화동통(華東統)은 표토(表土) 및 표토하부(表土下部)의 회색(灰色)을 제외(除外)하고 황갈색(黃褐色), 갈색(褐色)을 띠운다. 토양단면(土壤斷面)의 토성(土性)을 보면 공덕(孔德), 극락(極樂), 김제(金堤), 봉남부용(鳳南芙蓉), 호남(湖南) 및 화동통(華東統)은 식질(埴質)이고 백구(白鷗), 전북(全北) 및 지산통(芝山統)은 식양질(埴壤質) 혹은 미사식양질(微砂埴壤質)이며 광활(廣活), 만경(萬頃) 및 수암통(水岩統)은 미사사양질(微砂砂壤質) 그리고 신답(新踏) 및 화계통(華溪統)은 사질(砂質) 혹은 석력사질(石礫砂質)이다. 표토(表土)의 탄소함량(炭素含量)은 0.29%~2.18% 범위(範圍)에 있으나 1.0~2.0%인 것이 많으며 표토(表土)의 전질소함량(全窒素含量)은 0.03%~0.24% 범위(範圍)에 있다. 이들은 심토(心土) 혹은 기층(基層)으로 갈수록 감소(減少)되는 경향(傾向)이나 불규칙적(不規則的)이다. 표토(表土)의 탄질비(炭窒比)는 4.6~15.5 범위(範圍)인데 8~10인 것이 많으며 심토(心土) 및 기층(基層)에서는 표토(表土)에 비(比)하여 그 범위(範圍)가 커서 3.0~20.25이다. 토양반응(土壤反應)은 pH4.5~8.0 범위(範圍)에 있으나 광활(廣活) 및 만경통(萬頃統)을 제외(除外)하고는 모두 산성(酸性)이다. 염기치환용량(鹽基置換容量)은 표토(表土)에서는 5~13 me/100g 범위(範圍)이며 심토(心土) 및 기층(基層)에서는 사질토양(砂質土壤)을 제외(除外)하고 모두 10~20 me/100g 범위(範圍)에 있다. 염기포화도(鹽基飽和度)는 공덕(孔德) 및 백구통(白鷗統)을 제외(除外)하고는 모두 60% 이상(以上)이다. 표토(表土)의 활성철함량(活性鐵含量)은 0.45~1.81% 범위(範圍)이고 역환원성(易還元性)망간은 15~148ppm 범위(範圍)이며 유효규산은 36~366ppm 범위(範圍)에 있다. 이들 3성분(成分)의 용탈(溶脫) 및 집적(集積)은 토양배수(土壤排水), 토성조건(土性條件)에 따라 다르지만 대체(大體)로 10~70cm 범위(範圍)에 집적(集積)하고 있으나 규산(珪酸)은 경우(境遇)에 따라 철(鐵), 망간 보다 깊은 층위(層位)에 집적(集積)되여 있다. 각(各) 토양통(土壤統)의 주요특성(主要特性)은 해안(海岸)에서 부터 거리에 따라 점변(漸變)하고 있으며 점토(粘土), 유기탄소(有機炭素) 및 pH는 해안(海岸)으로 부터 내륙(內陸)으로 옮겨가는 거리와 다음과 같은 상관(相關)이 있다. y(표상(表上)의 점토함량(粘土含量)) = $$-0.2491x^2+6.0388x-1.1251$$ y (심토(心土) 및 표토하부(表土下部)의 점토함량(粘土含量)) = $$-0.31646x^+7.84818x-2.50008$$ y(표토(表土)의 유기탄소함량(有機炭素含量)) = $$-0.0089x^2+0.2192x+0.1366$$ 로서 내륙(內陸)으로 갈수록 높아지는 경향(傾向)이며 y(심토(心土) 및 표토하부(表土下部)의 pH) = $$0.0178x^2-0.4534x-8.353$$ 로서 내륙(內陸)으로 갈수록 낮다. 토양(土壤)의 형태(形態) 및 이화학적(理化學的) 특성(特性)에 있어 특기(特記)되는 것은 토양(土壤)의 발달도(發達度), 토색(土色), 모재(母材)의 다원적(多元的) 퇴적(堆積), 유기물층(有機物層)의 개입(介入), 토성(土性) 및 토양반응(土壤反應) 등(等)이였으며 이들은 답토양(畓土壤)의 분류(分類)에서 고려(考濾)되여야 할 사항(事項)이였다. 토양(土壤)의 몇가지 특성(特性)과 수도수량(水稻收量)과의 관계(關係)에서 토양배수(土壤排水)가 약간양호(若干良好) 내지(乃至) 불량(不良)한 식질토(埴質土), 양질토(壤質土) 그리고 유효심도가 낮은(50cm) 식질토(埴質土)들은 수량(收量)이 대부분(大部分) 10a당(當) 375kg 이상(以上)이며 사질토(砂質土), 배수(排水)가 양호(良好)한 식질토(埴質土), 유효심도가 낮은 양질토(壤質土) 및 함염토(含鹽土)들은 수량(收量)이 대부분(大部分) 10a당(當) 375kg미만(未滿)이다. 수도수량(水稻收量)에 영향(影響)을 미치는 토양(土壤)의 형태적(形態的) 특성(特性)은 토양배수(土壤排水), 토성(土性), 유효심도, 표토(表土) 및 표토하부(表土下部)의 회색화(灰色化) 그리고 염농도(鹽濃度) 등(等)이며 이들은 답토양(畓土壤)의 적성등급구분(適性等級區分)에서 고려(考慮)되여야 할 사항(事項)이였다. 2. 답토양(畓土壤)의 분류(分類) 및 적성등급구분(適性等級區分) 답토양(畓土壤)의 분류기준(分類基準)은 토양(土壤) 자체(自體)가 가지고 있는 성질(性質)에 근거(根據)를 두었다. 토양분류단위(土壤分類單位)는 토양대군(土壤大群), 토양군(土壤群), 토양아군(土壤亞群), 토양계(土壤系) 그리고 토양통(土壤統)의 5단계(段階)를 두고 분류(分類)의 기본(基本) 단위(單位)는 토양통(土壤統)으로 하였다. 토양분류(土壤分類)에 있어 형태적(形態的) 특성(特性)의 차이(差異)를 결정(決定)하기 위(爲)하여 2종류(種類)의 특징토층(特徵土層) 즉(卽) 숙성토층(熟成土層) 및 반숙토층(半熟土層)을 설정(設定)하여 이들의 유무(有無) 및 종류(種類)를 토양대군(土壤大群)의 분류기준(分類基準)으로 하였다. 토양군(土壤群) 및 토양아군(土壤亞群)의 분류(分類)에 있어 고려(考慮)되여야 할 특징적(特徵的) 토양특성(土壤特性)은 우선(于先), 토색(土色), 염농도(鹽濃度), 표토(表土) 및 표토(表土) 하부(下部)의 회색화(灰色化), 토사(土砂)의 다원적(多元的) 퇴적(堆積) 그리고 유기물층(有機物層)의 개입(介入)으로 하였으며 토양계(土壤系)의 분류(分類)에서 고려(考慮)한 토양특성(土壤特性)은 토양반응(土壤反應), 토성(土性) 및 석력함량(石礫含量)에 근거(根據)를 두어 분류(分類)하는 한편 이들에 대(對)한 정의(定義)를 내렸다. 그리고 필자(筆者)의 시안(試案)과 기존(旣存)의 분류안(分類案)을 상호비교(相互比較)하여 검토(檢討)하였다. 답토양(畓土壤)의 적성등급구분(適性等級區分)은 인위적(人爲的) 작용(作用)에 의(依)한 가변성(可變性)이 적은 토양특성(土壤特性)을 토대(土臺)로 하였으며 등급구분단위(等級區分單位)는 등급(等級) 및 아급(亞級)의 2단계(段階)를 두었다. 등급(等級)은 토양(土壤)의 잠재생산력(潛在生産力)이 어느 주어진 단위(範圍)에서 같고 토지이용(土地利用) 및 관리(管理)의 난이(難易)를 고려(考慮)한 토양조건(土壤條件)에 따라 1급(級)에서 4 급지(級地)까지의 4 등급(等級)으로 구분(區分)하였고 아급(亞級)은 동일등급내(同一等級內)에서 중요(重要)한 제한인자(制限因子)로 하였으며 그 인자(因子)는 경사(傾斜), 저염(低濕), 사질(砂質) 석력(石礫), 염해(鹽害), 미력(美熟)이다. 이들 등급(等級) 및 아급(亞級)을 각각(各各) 정의(定義)를 하였으며 아울러 분류시안(分類試案)과의 연관성(連關性)을 검토(檢討)하였다. 김제(金堤) 만경평야(萬頃平野)의 15개(個) 답토양통(畓土壤統)의 분류(分類) 및 적성등급(適性等級) 구분시안(區分試案)을 종합(綜合)하여 보면 다음과 같다.

• 한국산림과학회지
• /
• 제32권1호
• /
• pp.36-63
• /
• 1976

1974년(年) 천연(天然)소나무집단(集團)에 대한 유전적변이(遺傳的變異)를 분석(分析)하고져 먼저 경북(慶北) 청송군(靑松郡) 소재(所在) 주왕산(周王山)소나무림(林), 충남(忠南) 서산군(瑞山郡) 소재(所在) 안면도(安眠島) 소나무림(林), 그리고 강원도(江原道) 평창군(平昌郡) 소재(所在) 소나무림(林)을 대상(對象)으로하여 각(各) 집단(集團)에서 되도록 소면적(小面積)의 범위내(範圍內)에 서있는 소나무 개체(個體)를 각(各) 20주(株)씩 총 60주(株)를 택(擇)하여 그 모수(母樹)에 대한 형태학적(形態學的) 특성(特性)등을 조사측정(調査測定)하고 집단간(集團間)에 보이는 차이(差異) 그리고 한 집단내(集團內)에 있는 각개체수목(各個體樹木)의 형질(形質)을 조사보고(調査報告)한바 있다(제일보고문(第一報論文). 1974년(年) 가을에 가계별(家系別)로 종자(種字)을 채취(採取)하여서 가계별(家系別) 및 산지별(産地別)의 차이(差異)를 분석(分析)하고 동시(同時)에 그 종자(種字)를 파종하여서 1-0묘(苗) 및 1-1묘(苗)를 대상(對象)으로 생장인자(生長因子)에 대한 측정(測定)을 하고 그 유전력(遺傳力)을 계산(計算)해 보았다. 그밖에 엽록소함량(葉綠素含量) 또는 monoterpene등의 함량(含量)의 차이(差異)를 분석(分析)해 보았다. 종자(種字)의 형태학적(形態學的) 특성(特性)에 있어서는 집단간(集團間) 또 가계간(家系間)에 유의차(有意差)를 보이지 않는 것도 있었으나 대체(大體)로 유의차(有意差)가 인정(認定)되었다. 그리고 각형질간(各形質間)의 상관(相關)을 보았는데 구과폭(毬果幅)과 종자익(種字翼)의 폭(幅), 구과장(毬果長)과 종자익(種字翼)의 길이간(間), 그리고 구과(毬果) 생중량(生重量)과 종자중량간(種字重量間)에는 정(正)의 상관(相關)이 보였다. 묘고(苗高)와 근원경(根元徑)의 성장(成長)에 있어서는 가계간(家系間) 그리고 집단간(集團間)에 차이(差異)가 인정되었다. 묘고(苗高)의 유전력(遺傳力)은 집단(集團)의 평균치(平均値)를 가지고 분석(分析)하였다. 즉 집단(集團)에 관계(關係)되는 분산(分散)을 유전분산(遺傳分散)으로 보고서 유전력(遺傳力)을 계산(計算)해 보았는데 1-0묘(苗)의 묘고(苗高)에서는 0.29, 1-1묘(苗)에서는 0.14가 그리고 근원경(根元徑)에 있어서는 1-0묘(苗)는 0.15, 1-1묘(苗)에서는 0.06이였다. 기공열수(氣孔列數)에 있어서는 집단간차이(集團間差異)가 있었으나 거치밀도(鋸齒密度)에는 차이(差異)가 없었다. 침엽(針葉)의 특성(特性)에 관(關)해서는 모수(母樹)와 차대간(次代間)에 상관(相關)이 없었다. 엽록소함량(葉綠素含量)은 집단간차이(集團間差異)는 보였으나 가계간차이(家系間差異)는 없었다. monoterpene의 성분(成分)에 있어서는 myrcene과 ${\beta}$-phellandrene의 함량(含量)으로 집단차(集團差)를 볼 수 있었다.