• 대한기계학회논문집B
• /
• 제21권6호
• /
• pp.725-734
• /
• 1997

The effect of helical intake port geometry on in-cylinder swirl flow characteristics was studied. Two helical intake ports were selected to change swirl ratio, mean flow coefficient with the variation of valve lifts, valve eccentricity ratios and axial distance. The measurements were made by using an impulse swirl meter. The port B modified to increase the swirl ratio( $R_{s}$) had the tendency of the increased non-dimensional rig swirl ( $N_{r}$) distribution in comparison with that of the port A. And the $N_{r}$ distribution was remarkably improved at low valve lifts. The modification of the geometry to increase the swirl ratio ( $R_{s}$) in helical intake port resulted in the decrease of the mean flow coefficient ( $C_{f(mean)}$) regardless of valve eccentricity ratio ( $N_{y}$). And also non-dimensional rig swirl ( $N_{r}$) in the high valve lift affected the calculation of swirl ratio considerably.onsiderably.

• 한국해양공학회지
• /
• 제23권1호
• /
• pp.140-145
• /
• 2009

This paper deals with a stability evaluation of a butterfly valve using the body and disc of a valve seat. The experimental results of a strength evaluation are shown using STS316 stainless steel and spheroidal graphite cast iron (GCD450). The disc material was made from GCD450. The results of the strength analysis are as follows: Ultimate tensile strength 485MPa, Yield strength 370 MPa, Young's modulus $1.1{\times}10^5$, and Poisson's ratio v = 0.28. For the results of the disc analysis, the safety factor was about 4. This shows that a design was derived that satisfied the requirements of structural safety. However, some problems, such as the deflection and deformation of the disc, may occur when the sea water has back flow with a high pressure.

• 한국가스학회지
• /
• 제25권2호
• /
• pp.28-33
• /
• 2021

최근 친환경 자동차에 대한 관심이 높아짐에 따라 공해물질을 배출하지 않는 수소연료전지 차량에 대한 관심과 구매가 증가하고 있다. 최근 정부의 수소에너지 보급정책에 따라 수소충전소의 확충과 핵심부품의 국산화를 지원하고 있다. 본 연구에서는 그중에서도 수소 유량제어 밸브의 차압에 따른 유동특성을 연구하였다. 차압이 높아 짐에 따라 질량유량과 유량계수는 체적유량과 다른 경향을 보임을 확인하였다. 그리고 병목 구간에서의 노즐효과로 인해 수소온도에 영향을 주게되고, 밀도의 변화를 일으켜 질량유량에 영향을 주게 되는 것을 확인 하였다.

• 한국가스학회지
• /
• 제25권5호
• /
• pp.19-29
• /
• 2021

기후변화에 대응하기 위해 세계적으로 이산화탄소 및 대기오염 물질 배출 규제가 점차 강화됨에 따라 내연 기관 자동차를 친환경 자동차로 전환하려는 추세이다. 이는 정부의 수소 에너지 활성화 정책에 따른 충전 인프라 구축, 충전 설비 핵심 부품의 국산화 지원으로 가속화되고 있다. 본 연구에서는 유한 요소 해석을 통해 수소 연료 전지 자동차 용기 밸브의 과류 방지 장치를 설계하고, 시험을 통해 성능을 평가하였다. 주요 시험 항목인 정수압, 연속 작동, 압력 임펄스, 누설, 작동 시험을 ISO 12619-2, ISO 12619-11의 시험 방법에 따라 수행한 결과 요구 조건을 만족함을 확인하였다.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2004년도 하계학술연구발표회 논문개요집
• /
• pp.64-65
• /
• 2004

• 한국수소및신에너지학회논문집
• /
• 제19권4호
• /
• pp.331-339
• /
• 2008

본 논문은 내경 7.73 mm와 5.80mm의 수평관내 프레온계 냉매 R-22와 탄화수소계 냉매 R-290과 600a의 응축 열전달 계수의 실험적 결과를 나타내었다. 실험장치는 압축기, 응축기, 팽창밸브, 증발기 등으로 구성된다. 응축 실험은 질량유속 $35.5{\sim}210.4\;kg/m^2s$이고, 응축온도 40$^{\circ}C$인 조건에서 수행하였다. 주요 결과를 요약하면 다음과 같다. 탄화수소계 냉매 R-290과 R-600a의 평균 열전달 계수는 프레온계 냉매 R-22보다 높게 나타났으며, R-600a의 평균 열전달 계수가 모든 관경에 대해 가장 높게 나타났다. 실험결과와 종래의 상관식을 비교한 결과, 모든 관경과 냉매에 대해 Haraguchi 등의 상관식이 가장 좋은 일치를 보였다. 그 중에서 Cavallini-Zecchin의 상관식은 7.73 mm 관경의 실험데이터와, Dobson 등의 상관식은 내경 5.80 mm 관경의 데이터와 좋은 일치를 보였다.

• 동력기계공학회지
• /
• 제7권3호
• /
• pp.23-28
• /
• 2003

In heavy nuclear power plant, high energy through main steam line is provided to turbine that generate the electric power. Since plant had generated power, high noise has been occurred. Noise make equipments and work environment worse. For finding out the location and the cause of making noise, noise was measured along main steam line at open/close test of Main Steam Isolation Valve (MSIV hereafter). As the result, it was identified that the vortex shedding in the cavity of MSIV is main noise source. The profile change of MSIV seat ring was proposed as the method of noise reduction. After filletting MSIV seat ring, the noise level reduced $10{\sim}20dB$ compared before the change of profile.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2002년도 동계연구발표회 논문개요집
• /
• pp.158-159
• /
• 2002

스핀 밸브에서는 NiFe, CoFe, Cu등 주요 금속들이 면심입방체(111)로 배향이 용이하지만, 자기 터널 접합 소자에서는 $Al_2$O$_3$ 장벽층이 비정질로서 상부 강자성 전극이 충분히 (111) 배향을 할 수 없기 때문에 top bias 방식의 사용이 거의 불가능하며, bottom bias의 경우에도 교환 바이어스의 크기는 상대적으로 작다[1]. 이를 극복하기 위해 인공 초격자를 이용한 인공 반강자성층(synthetic antiferromagnet - SAF)을 이용하여 높은 교환 바이어스 효과를 구현하고자 하였다. (중략)

• 드라이브 ㆍ 컨트롤
• /
• 제18권4호
• /
• pp.1-8
• /
• 2021

An electro proportional pressure control valve is mainly used to control the clutch of an agricultural tractor's automatic transmission. During transmission, the operating, hydraulic oil is mix with many kinds of contaminants. The contaminants can be trapped between the valve body and spool of the proportional pressure control valve leading to abnormal operating conditions and finally critical damage to the transmission hydraulic system. The present study aimed to verify the valve control algorithm as a basic study of developing control logic that removes contaminants between the spool and the body of the proportional pressure control valve. To develop the algorithm, MATLAB/SIMULINK was used. PWM method was used to control the applied solenoid coil current. The effectiveness of the algorithm was verified by comparing the actual pressure of the normal valve with the actual pressure of the abnormal valve. Based on the present study findings, when the algorithm was applied, the response of the valve pressure according to the current became stable and oil contaminated particles were removed. In the future study, the control algorithm will be optimized for the stability of the proportional pressure reducing valve, and it will be verified in consideration with the driving of the clutch.

• 한국자동차공학회논문집
• /
• 제1권3호
• /
• pp.1-11
• /
• 1993

An experimental study was carried out to evaluate the characteristics of transient performance of carburettered gasoline engine under rapid accelerating transient driving conditions. In order to evaluate the characteristics of transient performance quantitatively, the concept of dead time $t_d$ response delay time $t_r$ are introduced. Performance parameters such as air mass fiowrate Gat, engine speed N, manifold boost pressure Pb, and output torque T are measured simultaneously during the rapid opening of the throttle valve by the stepping motor. During the rapid opening of the throttle valve, air mass fiowrate Gat is increased immediately without delay time, but response of engine revolution N, and output torque T are delayed. Therefore hesitation, and stumble phenomena are occurred. Dead time $t_d$ and response delay time $t_r$ of engine revolution N, which is extremely delayed comparing to other performance parameters, are respectively 0.2-0.3sec., 3.0-4.6sec., and dead time rate $t_d/{\Delta}t$ and response delay time rate $t_r/{\Delta}t$ are linearly increased with the throttle valve opening rate ${\theta}$ during the acceleration from 12 degree to 20 degree at 1250rpm.