• Journal of Welding and Joining
• /
• 제34권6호
• /
• pp.1-10
• /
• 2016

Flux Cored Wire is the most widely used welding material for Flux Cored Arc Welding these days. This paper introduces the technical aspects of manufacturing FCW and the development trend of FCW for each type of steel and metal. The studies are ongoing to lower the production cost of seamless-type FCW since it has not been generally used in welding shops so far because of it high cost even though the seamless-type FCW has various advantages than folded-type FCW in terms of manufacturing technology. Meanwhile, a technical research has been carried out to develop a rutile type of FCW products which satisfies high toughness after post heat treatment. In addition, for high-speed fillet welding, there has been a development of welding materials which can be welded in Single Auto-Carriage 100 cpm or more and up to Twin Tandem 200 cpm without occurring any welding defect in order to improve the welding productivity. As Zn coated steel is being used recently to improve the corrosion resistance of the automotive parts, a research and development for Metal Cored Wire has been conducted to reduce the Si island produced in welding operation than those produced when using the former solid wires. A development of welding material that guarantees CTOD performance beyond $-40^{\circ}C$ CTOD to $-60^{\circ}C$ is underway by different steel grades, and FCW for super austenitic stainless steel is being developed as the corrosion resistant steel has been upgraded.

• Journal of the Korean Society of Safety
• /
• 제14권1호
• /
• pp.101-107
• /
• 1999

$TiO_2$ and $xTiO_2-ySiO_2$ system photocatalysts were developed by sol-gel method based on the change of production parameters, and their structure of crystallization and the specific surface area was measured. Considering the efficiency of the ethanol decomposition using the catalyst, the conclusion was made as follows: 1) By means of X-ray analysis of $TiO_2$ powder that is obtained from water and Titanium alkoxide with various molar ratios, it is shown that structure of crystallization is a dominating structure and, on the other hand, the crystallization of rutile also partly exists. The specific surface area is at its maximum value at R=6, which is the molar ratio of water vs. alkoxide, whereas its value goes down as the molar ratio increases. In the reaction of using $TiO_2$ catalyst, the ethanol is decomposed into the extent of 15 ~30% in an hour and three hours are necessitated for 70% decomposition. 2) $TiO_2/SiO_2$ powder is developed from Titanium and Silicon alkoxide by a hetero-condensation process. The increase of SiO$_2$ contents causes the decrease of the degree of crystallization of the gel, whereas the specific surface area preferentially increases. In the decomposition reaction of the ethanol, the decomposition efficiency represents 25~60% in an hour. It is, however, examined that the efficiency inactively increases corresponding to the duration of reaction time. It is shown that more than 90% of ethanol is decomposed when reaction time is about three hours and the efficiency illustrates the maximum value for 60-$TiO_2/4O-SiO_2$ catalyst.

• Korean Chemical Engineering Research
• /
• 제53권3호
• /
• pp.276-281
• /
• 2015

Nanostructured $TiO_2-SiO_2$ materials have widely been used as anti-reflecting coating, optical-chemical sensors and catalysts because of their superior optical and thermal properties as well as chemical durability. Web type $SiO_2$ microfibers with nano-crystalline $TiO_2$ were prepared by electrospinning of Ti-PCS mixed solution and oxidation controlled heat-treatment, rather simple than sol-gel process. Nano-crystalline anatase phase were formed for the heat-treatment up to $1200^{\circ}C$ and they were finely dispersed in the amorphous $SiO_2$ matrix.

• Journal of the Korean Magnetics Society
• /
• 제23권1호
• /
• pp.7-11
• /
• 2013

We investigate the perpendicular magnetic anisotropy in $TiO_2$/Co/Pd on GaAs(100), MgO(100), MgO(111), Si(100), and glass substrates. We find that the roughness of $TiO_2$ depends on the $O_2$ partial pressure in the magnetron sputtering process. The perpendicular magnetic anisotropies are found in all substrates with $TiO_2$ seed layer, and the perpendicular magnetic anisotropy of Co/Pd system is insensitive on the type of the substrate when the thickness of $TiO_2$ seed layer is thicker than 5 nm. However, MgO(111) substrate promotes $TiO_2$ rutile (111) structure, and it causes largest perpendicular magnetic anisotropy in $TiO_2$/Co/Pd(111) structures.

• Bulletin of the Korean Chemical Society
• /
• 제30권1호
• /
• pp.219-223
• /
• 2009

$TiO_2$ doped with $Er^{3+\;and\;Yb^{3+}$ was used for fabricating a scattering layer and a nano-crystalline $TiO_2$ electrode layer to be used in dye-sensitized solar cells. The material was prepared using a new sol-gel combustion hybrid method with acetylene black as fuel. The $Er^{3+}$-$Yb^{3+}$ co-doped titanium oxide powder synthesized at 700oC had embossed structure morphology with a size between 27 to 54 nm that agglomerated to produce micron size particles, as observed by the scanning electron micrographs. The XRD patterns showed that the $Er^{3+}$-$Yb^{3+}$ co-doped titanium oxide had an amorphous structure, while using the same method without doping $Er^{3+}\;or\;Yb^{3+},\;TiO_2$ was obtained in the crystallite form with thea dominance of rutile phase. Fabricating a bilayer structure consisting of nano-crystalline $TiO_2$ and the synthesized $Er^{3+}$-$Yb^{3+}$ co-doped titanium oxide showed better scattering property, with an overall increase of 15.6% in efficiency of the solar cell with respect to a single nano-crystalline $TiO_2$ layer.

• Korean Journal of Materials Research
• /
• 제12권5호
• /
• pp.334-340
• /
• 2002

$TiO_2$-coated fly ash was synthesized by dropping method of coating agent in order to get $TiO_2$ coating layer with high photocatalytic activity on the surface of coal fly ash. The properties of the $TiO_2$ coating layer such as morphology, crystal structure, crystal size and photocatalytic activity were compared with those of the $TiO_2$-coated fly ash prepared by the traditional method of precipitation. $TiCl_4$ aqueous solution was used as a titanium stock solution and $NH_4HCO_3$ was used as a precipitant. The $TiO_2$ coating layer obtained by dropping method of coating agent was more uniform than that coated by precipitation. However, the crystal of $TiO_2$ coated by dropping method of coating agent was easy to grow by heat treatment because of the small primary particle size and bulky morphology, and its photocatalytic activity was consequently lower than that of the $TiO_2$ coated by precipitation. The $TiO_2$ coating layer obtained by both methods had a crystal structure of anatase, and the temperature of phase transformation into rutile was 90$0^{\circ}C$. The minimum crystal size of $TiO_2$ for the highest photocatalytic activity was found to be about 10nm.

• Journal of Surface Science and Engineering
• /
• 제36권1호
• /
• pp.14-21
• /
• 2003

Thin films of ZrO$_2$ and TiO$_2$ were deposited on Si(100) substrates using RF magnetron sputtering technique. To study an influence of the sputtering parameters, systematic experiments were carried out in this work. XRD data show that the $ZrO_2$ films were mainly grown in the [111] orientation at the annealing temperature between 800 and $1000^{\circ}C$ while the crystal growth direction was changed to be [012] at above $1000^{\circ}C$. FT-IR spectra show that the oxygen stretching peaks become strong due to $SiO_2$ layer formation between film layers and silicon surface after annealing, and proved that a diffusion caused by either oxygen atoms of $ZrO_2$ layers or air into the interface during annealing. Different crystal growth directions were observed with the various deposition parameters such as annealing temperature, RF power magnitude, and added $O_2$ amounts. The growth rate of $TiO_2$ thin films was increased with RF power magnitude up to 150 watt, and was then decreased due to a sputtering effect. The maximum growth rate observed at 150 watt was 1500 nm/hr. Highly oriented, crack-free, stoichiometric polycrystalline $TiO_2$<110> thin film with Rutile phase was obtained after annealing at $1000^{\circ}C$ for 1 hour.

• Journal of Sensor Science and Technology
• /
• 제20권2호
• /
• pp.82-89
• /
• 2011

Ruthenium(Ru)-doped $TiO_2$ nanofibers were prepared using electrospun Ru-$TiO_2$/poly(vinyl acetate) (PVAc) fibers and subsequent annealing for 1 h at temperatures in the range of $500^{\circ}C$ to $1000^{\circ}C$ in air. The properties of the Ru-$TiO_2$ fibers were characterized as a function of the Ru content and calcination temperature using X-ray diffraction, thermal gravimetry with differential scanning calorimetry, Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, and viscometer, pycnometer and dynamic tensiometer measurements. Although the diameter of the fiber decreased slightly with increasing calcination temperature, no dramatic changes were observed with respect to the ruthenium content. The XRD and FT-IR results revealed that anatase phase and ruthenium metal began to be formed after calcination at temperatures above $500^{\circ}C$. Anatase and rutile phases and ruthenium metal coexisted in the fibers calcined above $600^{\circ}C$. No anatase phase was detected in the fibers containing ruthenium when they were calcined at $1000^{\circ}C$. The morphology of the fibers changed from smooth and uniform to porous with increasing temperature. The experimental results suggest that the calcination temperature and Ru content were influential in determining the morphology and structure of the fibers.

• Environmental Analysis Health and Toxicology
• /
• 제26권
• /
• pp.3.1-3.6
• /
• 2011

Objectives: Titanium dioxide ($TiO_2$), a common nanoparticle widely used in industrial production, is one of nano-sized materials. The purpose of this study was to determine the acute and chronic toxicity of $TiO_2$ using different size and various concentrations on Daphnia magna. Methods: In the acute toxicity test, four concentrations (0, 0.5, 4, and 8 mM) for $TiO_2$ with 250 or 500 nm and five concentrations (0, 0.25, 0.5, 0.75, and 1 mM) for $TiO_2$ with 21 nm were selected to analyze the toxic effect to three groups of ten daphnia neonates over 96 hours. In addition, to better understand their toxicity, chronic toxicity was examined over 21 days using 0, 1, and 10 mM for each type of $TiO_2$. Results: Our results showed that all organisms died before the reproduction time at a concentration of 10 mM of $TiO_2$. In addition, the exposure of anatase (21 nm) particles were more toxic to D. magna, comparing with that of anatase (250 nm) and rutile (500 nm) particles. Conclusions: This study indicated that $TiO_2$ had adverse impacts on the survival, growth and reproduction of D. magna after the 21days exposure. In addition, the number of test organisms that were able to reproduce neonates gradually were reduced as the size of $TiO_2$ tested was decreased.

• Economic and Environmental Geology
• /
• 제29권6호
• /
• pp.689-698
• /
• 1996

The coal-bearing metapelites from the Hoenam area are interbedded within the Ogcheon Supergroup, which are composed mainly of graphite, quartz, muscovite and associated with trace amount of biotite, chlorite, pyrite, rutile and barite. Although the formation was mined for coal, and the contents of V, U and Mo are a higher grade in coal formations than the host metapelites. The ratios of Al/Na and K/Na in coal formation are very heterogeneous and wide range from 10.28 to 90.91 and from 3.73 to 36.60, respectively. The V content increase with increasing Al and Ba contents, but the U and Mo are not related with other elements. Those are suggested that controlled of mineral compositions in coaly metapelites due to substitution, migration and reequilibrium of elements by regional metamorphism. These coal formation were deposited in basin of marine environments and the REE of these rocks are not influenced with metamorphism and hydrothermal alterations on the basis of Al content versus La, La against Ce, the ratios of La/Ce (0.23 to 0.73) and Th/U (0.03 to 16.6). These rocks also show much variation in $La_N/Yb_N$ (0.53 to 14.19), Th/Yb (0.51 to 6.00) and La/Th (0.15 to 18.92), and their origin is explained by derivation from a mixture of sedimentary and metasedimentary rocks. The wide range in trace and REE element characteristics as Co/Th (0.07 to 3.00), La/Sc (0.04 to 23.48), Sc/Th (0.06 to 7.57), V/Ni (2 to 3319), Cr/V (0.03 to 1.06) and Ni/Co (1.00 to 79.85) of these coaly metapelites argues for inefficient mixing of the various source lithologies during sedimentation.