• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문 발표회
• /
• pp.59-62
• /
• 2003

Kinds, shapes and fraction ratios of fibers have influence on properties of HPFRCC(High-Performance Fiver Reinforced Cementitious Concrete) like bending strength, strain capacity and fracture toughness. For example, hydrophilic fibers have different chemical bond strength from hydrophobic fibers, fiber shapes influence on fiber pull-out and rupture, and fiber volume fraction influence on bending strength. In this study, to estimate influences of kinds, shapes and fraction ratios of fibers, we make HFRCC with 3 kind of fiber in various volume fraction of fiber and compare cracking, bending strength and fracture toughness. As the results, bending strength of HPFRCC was increased as fiber volume fraction was increase and fiber tensile strength was increase, and strain capacity and fracture toughness of HFRCC was higher in fiber pull-out fracture than in fiber rupture fracture. And HFRCC showing pseudo strain hardening has higher fiber reinforce efficiency than others.

• Journal of the Korean Wood Science and Technology
• /
• 제50권4호
• /
• pp.237-245
• /
• 2022

This study examined the structural performance of experimental parallel strand lumber (PSL) from a Larch veneer strand. The prototype of PSL from a Larch veneer strand was manufactured in the experimental laboratory and tested. The bending and dowel bearing strength were determined from the modulus of elasticity (MOE), modulus of rupture (MOR), and dowel bearing strength based on a 5% offset yield load. The test results indicated that the average MOR of PSL was higher than that of 2 × 4 dimension lumber, and the average MOE of PSL was lower than that of 2 × 4 dimension lumber. A linear relationship was observed between the MOR and MOE. The allowable bending stress of PSL was derived as specified in ASTM D2915 and compared with other research. The dowel bearing strength of PSL in parallel to the grain was approximately double that perpendicular to the grain of PSL. A comparison of several theoretical calculations based on each national code for the dowel bearing strength was conducted, and some theoretical equations produced results closer to the experimental results when it was parallel to the grain, but the difference was higher in the case perpendicular to the grain. The test results showed that PSL made with Japanese larch veneer strands appeared to be suitable for a raw material of structural composite lumber (SCL) appeared to be used as a raw material for SCL.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.22-27
• /
• 2004

Super-duralumin has widely been used as the part materials of aerospace and automobile industry because it has high specific strength and also is light. But, we have little design data about the creep behaviors of the alloy. Therefore, in this study, every creep test under four constant stress conditions have been conducted for four temperature conditions. A series of creep tests had been performed to get the basic design data and life prediction of super-duralurnin products and we have gotten the following results. First, the stress exponents showed the descending trend as the test temperatures increase. Secondly, the creep activation energy gradually decreased as the stresses become bigger. Thirdly, the constant of Larson-Miller parameters on this alloy was estimated about 6. And last, the fractographs at the creep rupture showed both the brittle fracture due to the transgranular rupture.

• 동력기계공학회지
• /
• 제6권4호
• /
• pp.49-55
• /
• 2002

In this paper, the elevated temperature tensile properties and short-time creep rupture characteristics were investigated for the friction welded joints of dissimilar materials, Cu-1%Cr-0.5%Zr and STS316L. The joining tests on Cu-1%Cr-0.5%Zr/STS316L by friction welding were performed, and optimum joining conditions of the friction welded joints were determined. The characteristics of the elevated temperature tensile strength, hardness, fractographs were examined, and the creep rupture characteristics for the optimum welded joints were investigated under uniaxal static load at 300, 400 and $500^{\circ}C$.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.309-317
• /
• 2012

Recent years have witnessed the use of micro shock tube in various engineering applications like micro combustion, micro propulsion, particle delivery systems etc. The flow characteristics occurring in the micro shock tube shows a considerable deviation from that of well established conventional macro shock tube due to very low Reynolds number and high Knudsen number effects. Also the diaphragm rupture process, which is considered to be instantaneous process in many of the conventional shock tubes, will be crucial for micro shock tubes in determining the near diaphragm flow field and shock formation. In the present study, an axi-symmetric CFD method has been applied to simulate the micro shock tube, with Maxwell's slip velocity and temperature jump boundary conditions. The effects of finite diaphragm rupture process on the flow field and the shock formation was investigated, in detail. The results show that the shock strength attenuates rapidly as it propagates through micro shock tubes.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2961-2966
• /
• 2007

When the pressure at the weak spot established at a certain part of a high pressure vessel or piping system exceeds a design pressure, this weak spot is burst, and the pressurized gas emitted through the weak spot will cause a compression wave system. In this connection, in the present study, an experimental study by using a conventional shock tube facility is performed to estimate the effects of the material of diaphragm, curvature radius and thickness of materials on the valve opening time in diaphragm. Pressure sensor having 500kHz in natural frequency is installed at 35mm downstream of the rupture diaphragm to measure the static pressure history of propagating and being accumulated compression wave. 4 kinds of materials are used as diaphragm that is aluminium, copper, stainless steel and zinc. The diaphragm radii of curvature R are ${\infty}$, 120mm and 60, respectively. And the depth for $90^{\circ}$ groove is 0.04mm. It is found that the smaller the tensile strength and elongation of the rupture diaphragm is, the smaller the radius of curvature of the rupture diaphragm is, and for the same conditions the thinner the thickness of the rupture diaphragm is, the shorter the valve opening time becomes. Also, the tensile strength, elongation and the radius of curvature of the rupture diaphragm for the same conditions are smaller, the maximum pressure rise caused by the coalescences of the compression wave is smaller. Finally the pressure ratio is higher, the valve opening time is shortened and gradient of pressure increment is more steepen.

• Journal of the Korean Wood Science and Technology
• /
• 제16권1호
• /
• pp.21-44
• /
• 1988

팔만칩 및 톱밥을 보오드에 활용(活用)하기 위한 방안(方案)의 하나로, 이들의 취약한 처리(物理) 및 기계적(機械的) 성질(性質)을 개선(改善)시키기 위하여 비목질재료(非木質材料)인 폴리프로필렌망(網)을 결체(結締)하여 보오드를 제조(製造)하였다. 보오드의 제조조건(製造條件)은 비중(比重)을 0.40, 0.55, 0.70 및 0.85의 4수준으로 하고 수지첨가율(樹脂添加率)을 8%, 10%, 12% 및 14%의 4수준으로 하였으며, 망수(網數)는 1장에서 4장으로 하여 보오드를 각각 제조(製造)하였다. 이들 보오드의 물리(物理) 및 기계적(機械的) 성질(性質)은 두께팽창율(膨脹率), 휨파괴계수(破壞係數), 휨탄성계수(彈性係數), 인장강도(引張强度), 박리저항(剝離抵抗) 및 나사못보지력(保持力) 등을 측정조사(測定調査)하고 고찰(考察)하였는데 본연구(本硏究)에서 얻은 중요한 결론(結論)은 다음과 같다. 1) 지수첨가율(指數添加率)이 증가함에 따라 두께팽창율(膨脹率)은 감소(減少)하였고, press-lam 보오드는 일반성형(一般成形)보오드 보다 낮은 값을 보여 주었다. 2) 보오드의 휨파괴계수(破壞係數) 및 탄성계수(彈性系數)는 비중(比重)이 증가하였으며 press-lam 보오 드는 일반적형(一般的形)보오드보다 높은 값을 나타내었다. 망수(網數)가 증가함에 따라 휨파괴계수(破壞係數)는 증가하였고, 수지첨가율(樹脂添加率)이 증가함에 따라서도 같은 양상이 나타났으나 휨탄성계수(彈性係數)의 경우 망수(網數)에 따른 효과(效果)는 나타나지 아니하였다. 3) 비중(比重)이 증가함에 따라 보오드의 인장강도(引張强度)는 증가하였으며, 망구성(網構成)보오드는 대조보오드보다 높은 값을 나타내었다. 또 망수(網數)가 증가함에 따라서도 인장강도(引張强度)는 증가하였으며, press-lam 보오드는 일반적형(一般的形)보오드보다 높은 인장강도치(引張强度値)를 보여 주었다. 4) 보오드의 박리저항(剝離抵抗)은 비중(比重)이 증가함에 따라 증가하였으며 망(網)을 결체(結締)한 보오드는 대조보오드 보다 모두 낮은 값을 보여 주었다. 기수매구성(奇數枚構成)보오드는 우수매구성(偶數枚構成)보오드보다 낮은 박리저항치(剝離抵抗値)를 보였다. 5) 수지첨가율(樹脂添加率) 및 비중(比重)이 증가함에 따라 나사못 보지력(保持力)은 증가하였으나, 망구성(網構成)보오드와 대조보오드사이에서의 차이는 크지 아니하였다. presslam 보오드에서 팔만칩보오드의 경우 고비중(高比重)보오드가, 톱밥보오드의 경우 저비중(低比重)보오드가 각각 대조보오드보다 높은 값을 보여 주었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2003년도 춘계학술강연 및 발표대회
• /
• pp.47-48
• /
• 2003

• Advances in concrete construction
• /
• 제7권1호
• /
• pp.31-37
• /
• 2019

This paper evaluates the workability and hardened properties of self-compacting concrete (SCC) containing silica fume as the partial replacement of cement. SCC mixtures with 0, 2, 4, 6, 8 and 10% silica fume were tested for fresh and hardened properties. Slump flow with $T_{500}$ time, L-box and V-funnel tests were performed for evaluating the workability properties of SCC mixtures. Compressive strength, splitting tensile strength and modulus of rupture were performed on hardened SCC mixtures. Experiments revealed that replacement of cement by silica fume equal to and more than 4% reduced the slump flow diameter and increased the $T_{500}$ and V-funnel time linearly. Compressive strength, splitting tensile strength and modulus of rupture increased with increasing the replacement level of cement by silica fume and were found to be maximum for SCC mixture with 10% silica fume. Further, residual hardened properties of SCC mixture yielding maximum strengths (i.e., SCC with 10% silica fume) were determined experimentally after heating the concrete samples up to 200, 400, 600 and $800^{\circ}C$. Reductions in hardened properties up to $200^{\circ}C$ were found to be very close to normal vibrated concrete (NVC). For 400 and $600^{\circ}C$ reductions in hardened properties of SCC were found to be more than NVC of the same strength. Explosive spalling occurred in concrete specimens before reaching $800^{\circ}C$.

• 한국운동역학회지
• /
• 제31권4호
• /
• pp.241-248
• /
• 2021

Objective: The purpose of this study was to investigate the difference in muscle strength, kinematics, and kinetics between injured and non-injured sides of the leg after Achilles Tendon Rupture surgery during walking and running. Method: The subjects (n=11; age = 30.63 ± 5.69 yrs; height = 172.00 ± 4.47 cm; mass = 77.00 ± 11.34 kg; time lapse from surgery = 29.81 ± 10.27 months) who experienced Achilles Tendon Rupture (ATR) surgery participated in this study. The walking and running trials were collected using infrared cameras (Oqus 300, Qualisys, Sweden, 100 Hz) on instrumented treadmill (Bertec, U.S.A., 1,000 Hz) and analyzed by using QTM (Qualisys Track Manager Ver. 2.15; Qualisys, U.S.A). The measured data were processed using Visual 3D (C-motion Inc., U.S.A.). The cutoff frequencies were set as 6 Hz and 12 Hz for walking and running kinematics respectively, while 100 Hz was used for force plate data. Results: In ATR group, muscle strength there were no difference between affected and unaffected sides (p> .05). In kinematic analysis, subjects showed greater ROM of knee joint flexion-extension in affected side compared to that of unaffected side during walking while smaller ROM of ankle dorsi-plantar and peak knee flexion were observed during running (p< .05). In kinetic analysis, subjects showed lower knee extension moment (running at 2.2 m/s) and positive ankle plantar-flexion power (running at 2.2 m/s, 3.3 m/s) in affected side compared to that of unaffected side (p< .05). This lower positive ankle joint power during a propulsive phase of running is related to slower ankle joint velocity in affected side of the subjects (p< .05). Conclusion: This study aimed to investigate the functional evaluation of the individuals after Achilles tendon rupture surgery through biomechanical analysis during walking and running trials. Based on the findings, greater reduction in dynamic joint function (i.e. lower positive ankle joint power) was found in the affected side of the leg compared to the unaffected side during running while there were no meaningful differences in ankle muscle strength and walking biomechanics. Therefore, before returning to daily life and sports activities, biomechanical analysis using more dynamic movements such as running and jumping trials followed by current clinical evaluations would be helpful in preventing Achilles tendon re-rupture or secondary injury.