• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.473-477
• /
• 2005

This paper presents a highly efficient HDD (Hard Disk Drive) spindle motor with a passive magnetic thrust bearing and a fluid dynamic journal bearing and its effectiveness is verified through experiment. It eliminates the mechanical friction loss of a thrust bearing which is around 18% of total power consumption of a 3.5' HDD spindle motor, by replacing a conventional fluid dynamic thrust bearing with a passive magnetic thrust bearing. The passive magnetic thrust bearing using permanent magnets is inherently unstable in radial direction. However, the radial fluid dynamic force of the fluid dynamic journal bearing counterbalances the radial magnetic force of magnetic thrust bearing to achieve the stability as the motor spins up. It has less or equivalent runout and less flying height than the conventional spindle motor.

• Journal of the Korean Society of Safety
• /
• v.21 no.3 s.75
• /
• pp.1-7
• /
• 2006

Nowadays, out of other transmission parts, the sleeve is getting more and more important part for exact and smooth shifting from gear ratio change whenever drivers are needed. To exact and smooth shifting when drivers are needed, all the parts connected with gear shifting should be machined exactly and having dimensions designers are intended. Especially, in case of the sleeve that the most important functional part to shift from gear ratio change that drivers are intended, it needs high precision grade and quality in both sides runout and outer dia runout as well as inner spline small dia & large dia. Because it's assembled with the synchro hub spline and shifted directly with the mating cone. So, it should be applied the hear treatment(hereinafter referred to H.T.M.T) to prevent the friction and percussion loss from shifting with mating cone. At this time, the deformation problems are raised from almost H.T.M.T. process and it makes the inferior part.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.11
• /
• pp.1176-1181
• /
• 2004

In high-capacity disk drives with ever-growing track density, the allowable level of position error signal(PES) is becoming smaller and smaller. In order to achieve the high TPI(track per inch) disk drive, it is necessary to improve the writing accuracy during the servo track writing(STW) Process through the reduction of track mis-registration sources. Among the main contributors of the non-repeatable runout(NRRO) PES, the disk vibration and the head-stack assembly vibration is considered to be one of the most significant factors. Also the most contributors of repeatable runout(RRO) come from the contributors of NRRO which is written-in at the time of STW process. In this paper, the effect of NRRO on servo written-in RRO is Investigated by experimentally, and the experimental result shows that the written-in RRO can be effectively reduced through a STW process under low dense medium condition such as semi-vacuum.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1159-1165
• /
• 2011

The recording density of HDD is increasing in ratio of 100% each year. Because the increasing of recording density requires the feature of high rotation, fixation and low-noise, fluid hydrodynamic bearing(FDB) has been paid attention to overcome a limitation in ball bearing. Most of researches related to improving performance of FDB have been studied in Japan which has 80% more market share of HDD spindle motor assembly. Main subject of studies are about for the design of the groove shape, manufacturing process of fluid dynamic bearing, performance evaluation and measurement. In HDD, non-repeatable runout(NRRO) is most important parameter which determines the performance of HDD spindle system because NRRO is unpredictable that cannot be compensated in head/slider servo system. In this study, performance evaluation system can measure dynamic behaviors were designed and methodology for calculating imbalance, RRO, and NRRO were proposed.

• The Journal of Engineering Geology
• /
• v.15 no.2 s.42
• /
• pp.185-199
• /
• 2005

Properties of sliding materials are dependent on the lithology because debris is the product of rock weathering processes. In order to characterize transportation behavior of debris dependent of debris types, this study selected 26 debris flows over three areas composed with different rock weathering types and topographic conditions. Analyses of lithology, weathering, and topographic characteristics were performed by detailed field survey. Based on the field survey data, transportation behavior of debris was studied at the aspect of the relationship of grain size and volume of debris as well as topographic conditions. According to the study results, change of slope angle is very influential factor on runout distance of debris among the topographic factors. Because the sliding velocity and the energy of debris are frequently changed and more irregular on an undulating slope, the unout distance of debris is larger than that of an uniformly dipping slope. Runout distance of debris is also influenced by volume and grain size of debris. Volume of debris in the gabbro is four or five times larger than that of the granite area because it is controlled by the lithology. Considered with grain size distribution, runout distance of debris is longer in the gabbro area which is composed with irregular grain size bearing large corestones than that in the medium grained granite area.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.61-65
• /
• 1993

절삭작업에 있어서 생산기술자가 제품을 경제적으로 생산하기 위해서는 기계의 사양이나 요구되는 제품의 정밀도 등 을 고려하여 목적에 맞는 절삭조건을 선택하여야 한다. 특히 임금이 과거에비해 크게 오르고 기계의 가격이 자동화로 인하여 고가가 됨에 따라서 기계의 효율적 운용이 점점 더 중요하게 되었다. 따라서 목적에 맞는 절삭조건의 선정은 기업의 경쟁력 향상에 있어서 중요한 문제로 부상되고 있다. 본 논문에서는 정면밀링작업시, 인서트 초기위치오차( Runout)를 고려한 표면조도와 절삭력 시뮬레이션 프로그램을 이용하여 구한 허용동력을 제한조건으로 고려하여 보다 실제에 가까운 상황에서 최소비용과 최대 생산율을 얻도록 프로그램을 개발하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.49-54
• /
• 1994

A dynamic model for the cutting process in the end milling process is developed. This model, which describes the dynamic response of the end mill, the chip load geometry including tool runout, the dependence of the cutting forces on the chip load, is used to predict the dynamic cutting force during the end milling process. In order to predict accurately cutting forces and tool vibration, the model, which uses instantaneous specific cutting force, includes both regenerative effect and penetration effect. The model is verified through comparisons of model predicted cutting force with measured cutting forces obtained from machining experiments.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.532-535
• /
• 2003

Vibration of rotating machinery is a factor that is something to do with abnormal machinery. Former days, Perception of vibration at rotating machinery had used Shaft rider type. Shaft rider type was adhered to surface of shaft and detected vibration of rotating machinery. Recently, Perception of vibration at rotating machinery uses to non-contact sensor. Working principle of non-contact sensor is used of eddy current. Vibration at rotating machinery appears to deviation of eddy current. In this paper, We investigate abnormal vibration due to non-contact sensor.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.468-473
• /
• 2002

This paper presents the methodology for measuring eccentricity of the cylindricaliy machined part using CCS(Cylindrical Capacity Spindle Sensor) signal in the CNC turning process. In order to investigate the relationships between CCS orbits and eccentricities, the initial conditions for various eccentricity state and machining process is applied to the experimental strategy. AS a result, it is considered the linearities of CCS signal and magnitude of eccentricity of machined cylindrical surfaces based on the possibility as a automatic detection apparatus for the CNC lathe.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.12-19
• /
• 2006

Landslide model experiments considering hourly rainfall were performed to investigate and predict the run out distance induced by landslides. The model flume and the rainfall simulator were designed and produced. The model flume was designed in consideration of the landslide characteristics of Korea. The landslides in Korea were mainly occurred in the interface between soil layer and rock layer. The rainfall simulator was produced for controlling hourly rainfall ranged from 100mm/hr to 1,000mm/hr. Jumnunjin standard sand as slope soils was placed on the model flume. The model experiments were performed with changing the hourly rainfall ranged from 150mm/hr to 250mm/hr. In this experiments, the inclination of slope was 25o and the relative density of slope soils was 35%. As a result of experiments, the pore water pressure is rapidly increased at landslide occurring time, and the scale of landslide is increased with increasing in hourly rainfall. The spreading range of run out distance is occurred with pan type, and the spreading width and length are rapidly increased in its early stage and slowly increased after early stage. Also, The increasing velocity of run out distance of debris is influenced by hourly rainfall.