• Proceedings of the Korean Reliability Society Conference
• /
• 2006.05a
• /
• pp.40-47
• /
• 2006

Rail car axles are very important parts for safety of passengers and structural integrity of vehicles. The axles are supported by bearings. To seal grease lubricating the bearings of freight cars, a non-contact oil seal has been developed. The developed oil seal is composed of inner plate, outer plate and seal rubber. The friction between axle and housing with the developed oil seal is very low. The seals are designed for a minimum life expectancy of 800,000 kilometers service. In this study, an accelerated durability tests according to AAR Specification M-934-82 were carried out. Developed products satisfy the AAR Specifications.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.973-978
• /
• 2007

In this paper, we make a study of a thermal deformation by FEM and test to define the deformation mode of the Vacuum-Cleaner's Nozzle-Cover. In FEM analysis, 3 different conditions were considered separately, such as (1) Compressive force by Belt tension, (2) Friction heat between Belt and Shaft and (3) Compressive force combined with heat. Throughout FEM analysis it was found that the deformation was caused by heat and it was proved through a simulation test with a real product.

• Elastomers and Composites
• /
• v.58 no.2
• /
• pp.87-94
• /
• 2023

Abrasion tests of an SBR compound were conducted using four different types of abrasion testers (cut and chip, Lambourn, DIN, and LAT100). The abrasion test results were analyzed in terms of size distributions and morphologies of the wear particles. Most wear particles were larger than 1000 ㎛. The wear particle size distributions tended to decrease as the particle size decreased. Except for the Lambourn abrasion test, the wear particles smaller than 212 ㎛ were rarely generated by the other three abrasion tests, implying that small wear particles were produced through friction by introducing talc powder. Shapes of the wear particles varied depending on the abrasion testers. The wear particles generated from the Lambourn abrasion tester had stick-like shapes. The cut and chip abrasion test showed a clear abrasion pattern, but the DIN abrasion test did not show any specific abrasion pattern. The Lambourn and LAT100 abrasion tests showed irregular abrasion patterns.

• Elastomers and Composites
• /
• v.58 no.2
• /
• pp.81-86
• /
• 2023

Asphalt pavements are generally composed of fine and coarse aggregates, bitumen, and modifier. Asphalt pavement wear particles (APWPs) are produced by friction between the road surface and the tire tread, and they flow into the environment such as rivers and oceans. Model APWPs were prepared and a single APWP of 212-500 (S-APWP) and 500-1000 ㎛ (L-APWP) was analyzed using thermogravimetric analysis (TGA) to investigate inhomogeneity in the compositions of the APWPs. The reference TGA thermogram was built using thermograms of the raw materials and formulation of the model asphalt pavement. The compositions of the APWPs were different from each other. Ash contents of the APWPs were lower than expected. Inhomogeneity in the total contents of bitumen and modifier was more severe than that in the other components. The inhomogeneity of the S-APWPs was more severe than that of the L-APWPs.

• Elastomers and Composites
• /
• v.46 no.2
• /
• pp.144-151
• /
• 2011

Intermittent CSR testing was used to investigate the degradation of a hydrogenated NBR(HNBR) O-rings, and also the prediction of its life-time. The cure system of HNBR O-ring was controlled as sulfur cure and peroxide cure system. An intermittent CSR jig was designed taking into consideration the O-ring's environment under use. The testing allowed observation of the effects of friction, heat loss, and stress relaxation by the Mullins effect. Degradation of O-rings by thermal aging was observed between 100 and $120^{\circ}C$. In the temperature range of $100-120^{\circ}C$, O-rings showed linear degradation behavior and satisfied the Arrhenius relationship. The activation energy of HNBR-S was about 70.6 kJ/mol. From Arrhenius plots, predicted life-times of HNBR-S O-ring were 31.1 years and 33.7 years for 50% and 40% failure conditions, respectively. In case of HNBR-P, the activation energy was about 72.1kJ/mol, and predicted life-times were 34.0 years and 36.5 years for 50% and 40% failure conditions, respectively. The peroxide cure system showed slower degradation rate and higher activation energy than the sulfur cure system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.3
• /
• pp.1385-1390
• /
• 2012

Couple of laboratory for controlled low strength materials with bottom ash and recycled in-situ soil have been carried out. The optimum mix ratios for 4 cases with flowability and unconfined compressive strength were determined. The optimim mixing ratios were 25 to 45% of insitu soil, 30% of bottom ash, 10 to 20% of fly ash, 0 to 3% of crumb rubber, 3% of cement and 22% of water. Each mixture was satisfied the standard specification, minimum 20cm of flowability and 127 kPa of unconfined compressive strength. Two different curling methods, at room temperature and wet condition, were adopted. The average secant modulus(E50) was 0.07 to 0.08 * $q_u$. The compressive strength at wet condition showed 10% larger than at room temperature. The range of internal friction angle and cohesion for mixtures were 36.5o to 46.6o and 49.1 to 180 kPa, respectively. The mixture with crumb rubber(case 4) showed higher choesion and lower internal friction angle than the others. The pH of all the mixtures was over 12 which is strong alkine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.10-16
• /
• 2007

A rubber seal for wheel bearing which has been mainly applied to car wheel supporting device is required to have both high sealing performance and drag torque. Because of severe operational conditions like infiltration of mud or splashed water, the importance of rubber seal which is aimed for leakage prevention of grease and effective blocking of foreign substances has been increasing continuously. The sealing performance of this seal depends on several factors such as materials of seal, friction conditions of contact regions and geometry of seals and so on. We have focused on the effects of geometric characteristics such as the angle of main lip, interference between lip edge and inner metallic ring. In this study, the optimization of geometric variables was performed using the finite element analysis. For the sake of finite element analysis, uniaxial tensile tests were conducted and several constants for Mooney-Rivlin's equation were obtained. According to the results of this study, mock-up bearing was made. To verify this study, drag torque and mud spray test were preformed.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.578-585
• /
• 2000

Geometrical characteristics of fresh red pepper(Capsicum annuum L.) were measured and indexed to define some important geometrical characteristics, and malformation of body and fruit stalk which are necessary for the design of the equipments for cutting, spreading and alignment of red pepper in developing a fruit stalk remover of fresh red pepper. The effects of bending of body and fruit stalk on the equipments of cutting, spreading and alignment were studied. The maximum lengths of some parts of fresh red pepper were found to be 180 mm, 125 mm, 144 mm, 67 mm and 76 mm for the body, the bent part of body, the fruit stalk, the bent part and the straight part of fruit stalk, respectively. The fresh red pepper with bending indices more than 0.4 and 0.3 for the body and the fruit stalk, respectively, was defined to be malformed based on the result of cutting rate using cutting unit; while the other ones to be normal in shape. Based on this, among the total fresh red peppers tested, 47%, 40% and 20% were found malformed for the body, the fruit stalk, and for both of the body and the fruit stalk. Malformed red peppers were poorer in spreading and alignment than normal ones, and the processed quantity was decreased with increased feed rate. The required time for the malformed peppers to pass on the alignment plate inclined at 30 increased rapidly at 8.3 Hz with increased feed rate. For the fresh red peppers with average moisture content of 85%,w.b., the maximum tensile strength between fruit stalk and body was 88.1 N; the maximum cutting resistances were 92.1 N and 94.9 N for the fruit stalk-calyx joint and body, respectively. Average coefficients of static friction were 0.99, 0.62, 0.59 and OJ, respectively, for the surfaces of rubber, galvanized iron, acryl and plywood.

• Journal of Drive and Control
• /
• v.18 no.4
• /
• pp.77-83
• /
• 2021

With the progress in virtual reality technology, various virtual objects can be displayed using head-mounted displays (HMD). However, force feedback sensations such as pushing against a virtual object are not possible with an HMD only. Focusing on force feedback, desktop-type devices are generally used, but the user cannot move in a virtual space because such devices are fixed on a desk. With a wearable force feedback device, users can move around while experiencing force feedback. Therefore, the authors have developed a wearable force feedback device using a magnetorheological fluid clutch and pneumatic rubber artificial muscle, aiming at presenting the elasticity, friction, and viscosity of an object. To date, we have developed a wearable four-degree-of-freedom (4-DOF) force feedback device and have quantitatively evaluated that it can present commanded elastic, frictional, and viscous forces to the end effector. However, sensory evaluation with a human has not been performed. In this paper, therefore, we conduct a sensory evaluation of the proposed method. In the experiment, frictional and viscous forces are rendered in a virtual space using a 4-DOF force feedback device. Subjects are asked to answer questions on a 1- to 7-point scale, from 1 (not at all) to 4 (neither) to 7 (strongly). The Wilcoxon signed rank test was used for all data, and answer 4 (neither) was used as compared standard data. The experimental results confirmed that the user could feel the presence or absence of viscous and frictional forces. However, the magnitude of those forces was not sensed correctly.

• Earthquakes and Structures
• /
• v.10 no.2
• /
• pp.293-311
• /
• 2016

A parametric study on the nonlinear seismic response of isolated reinforced concrete structural frame is presented. Three prototype frames designed according to the 1954 Hellenic seismic code, with number of floor ranging from 1 to 3 were considered. These low rise frames are representative of many existing reinforced concrete buildings in Greece. The efficacy of the implementation of both lead rubber bearings (LRB) and friction pendulum isolators (FPI) base isolation systems were examined. The selection of the isolation devices was made according to the ratio $T_{is}/T_{fb}$, where Tis is the period of the base isolation system and $T_{bf}$ is the period of the fixed-base building. The main purpose of this comprehensive study is to investigate the effect of the isolation system period on the seismic response of inadequately designed low rise buildings. Thus, the implementation of isolation systems which correspond to the ratio $T_{is}/T_{fb}$ that values from 3 to 5 is studied. Nonlinear time history analyses were performed to investigate the response of the isolated structures using a set of three natural seismic ground motions. The evaluation of each retrofitting case was made in terms of storey drift and storey shear force while in view of serviceability it was made in terms of storey acceleration. Finally, the maximum developed displacements and the residual displacements of the isolation systems are presented.