• Elastomers and Composites
• /
• v.49 no.1
• /
• pp.66-72
• /
• 2014

Carbon coating on silica particles is done by grafting expanded graphite on the silica aggregates. Successful coating of carbon is corroborated using FT-IR, TGA, XPS and TEM. Crystalline nature of coated graphite is corroborated using XRD. Influence of carbon coated silica particles on rheometric and mechanical properties of SBR composites are investigated. Carbon coated silica particles showed significant improvement in rheometric and mechanical properties, when compared to pristine silica filled system corroborating higher polymer-filler adhesion. This fact was further supported by bound rubber content and equilibrium swelling ratios of unvulcanized and vulcanized SBR composites.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1210-1212
• /
• 1997

This study describes the influence of the size of the median particles of alumina trihydrated(ATH) filler on the tracking resistance, tensile properties, dielectric properties and water immersion properties of EPDM rubber. A fixed 100pph concentration of the filler of A TH was used for all particle sizes from 0.7 to $20{\mu}m$. It is shown that tracking and erosion resistance decrease with increasing particle size, whereas tensile properties and dielectric properties are improved with increasing particle size of ATH.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1239-1241
• /
• 1993

This paper studies on the improvement of non-tracking property which is very important matter for developing polymer insulator. Non-Tracking property of silicon rubber used for polymer insulator was investigated by ASTM D 2303 according to Aluminium Hydrate filler. Furthermore other electrical and mechanical properties were estimated. The optimum amount of Aluminium Hydrate should be considered by following test results.

• Elastomers and Composites
• /
• v.30 no.3
• /
• pp.207-217
• /
• 1995

The reinforcement of Inorganic filler silica treated with LBR-MDI In SBR vulcanizates were Investigated. The inorganic filler silica treated with MDI on unmodified surface and that of silica treated by MDI was retreated with LBR. The charateristics of vulcanization, physical properties, surface properites and dynamic properties were investigated after mixing those silica with SBR and unmodified silica with SBR. Rheometric studies of the vulcanization showed that S-series has fast scorch $time(t_{10})$ and an optimum cure $time(t_{90})$ in the SBR compounds. And it was turned out that SBR vulcanizates compounded with LBR treated silica was better than any other componnds in hardness, tensile strenght, 100 300% modula and elongation. We could confirm that urea bonding is formed from IR spectrum. We concluded that L-series shows the best reinforcement effect in SBR vulcanizates.

• Journal of Environmental Science International
• /
• v.19 no.3
• /
• pp.365-370
• /
• 2010

In this study, we carried out the evaluation of EPDM(Ethylene Propylene Diene Monomer) reclaimed rubber mixing with natural rubber at various mixing ratio to reuse as rubber filler. The scorch time and moony viscosity was analyzed to evaluate the effect of cure behavior. And also, we analyzed the tensile strength, the elongation at break and cure time to evaluate the variation of cure behavior. As the results, the scorch time and optimal cure time was decreased according to the increasing of EPDM reclaimed rubber. However, the moony viscosity was increased at each mixing ratio. In case of the added EPDM reclaimed rubber was 20 phr(parts by weight per 100 parts by weight of rubber), the hardness and specific gravity was increased a little. The hardness and specific gravity was increased in rapidly under 40 phr of the added EPEM reclaimed rubber. The tensile strength and elongation at break of the compound of natural and EPDM reclaimed rubber was rapidly decreased compared with its natural rubber when the ratio of adding EPDM reclaimed rubber was over 40 phr.

• Elastomers and Composites
• /
• v.48 no.3
• /
• pp.181-189
• /
• 2013

Unfilled, carbon black-filled, and silica-filled natural rubber (NR) composites were aged with a circular deformation at $60-90^{\circ}C$ and the recovery behaviors were investigated. The samples were aged under the altering aging medium systems of air and distilled water every day for 10 days. The order of the recoveries according to the filler systems was unfilled > silica > carbon black. The recoveries of the samples aged in the air to water altering system were greater than those of the samples aged in the water to air altering system. The initial aging medium dominantly influenced the deformation level.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.2
• /
• pp.345-353
• /
• 2013

This paper discusses the experimental results in an effort to understand the tracking and erosion resistance of the micro and nano size $Al_2O_3$ filled silicone rubber (SIR) material which has been studied under the AC voltages, with ammonium chloride as a contaminant, as per IEC 60587 test procedures. The characteristic changes in the tracking resistance of the micro and nano size filled specimens were analyzed through leakage current measurement and the eroded masses were used to evaluate the relative erosion and tracking resistance of the composites. The fundamental, third and fifth harmonic of the leakage current during the tracking study were analyzed using moving average current technique. It was observed that the harmonic components of leakage current show good correlation with the tracking and erosion resistance of the material. The thermogravimetry-derivative thermo gravimetric (TG-DTG) studies were performed to understand the thermal degradation of the composites. The physical and chemical studies were carried out by using scanning electron microscope (SEM), Energy Dispersive X-ray analysis (EDAX) and Fourier Transform Infra-red (FTIR) Spectroscopy. The obtained result indicated that the performance of nano filled SIR was better than the micro filled SIR material when the % wt. of filler increased.

• Elastomers and Composites
• /
• v.40 no.2
• /
• pp.93-103
• /
• 2005

In this study, surface treatment of the elastomeric matrix was investigated to develop a substituting material for steel dynamic damper of automobile. The key technology is to get ultra high density elastomeric compound in order to substitute steel dynamic damper. The optimum matrix material(chloroprene rubber) and filler(metal powder) were selected for this. The several properties of elastomeric compound were examined. According to the results, the $t_{s2}$ of filled elastomeric compound was decreased with increasing the filler loading whereas the $t_{90}$ was increased. Also, tensile strength and rebound resilience were decreased with filler loading. To solve the problem of high filler loading, the photo grafting technique was employed on elastomeric matrix. The degree of grafting was determined by FTIR-ATR. Also, the filler surface was modified by chemical etching and the surface morphology was examine by SEM. After chemical treatment of filler, the particle size analyzer was used to examined the particle size, size distribution, and morphology of the modified filler.

• Elastomers and Composites
• /
• v.31 no.2
• /
• pp.111-121
• /
• 1996

The characteristic of silicone rubber can be seen from its resistance to both low and high temperature, whereas HNBR is resistant only in high temperature moderatly although it can be compounded to give good tensile properties, good oil resistance while silicone rubber severely lacks in these qualities. This study was initiated a balance of properties by blending HNBR and silicone rubber which is not considered for commercial blending; blends of HNBR with silicone rubber tend to show immiscible due to dissimilar nature of silicone and HNBR, the possibility of phase separation cannot be ruled out, in unfilled system after vulcanisation leading to premature failure. Attempt has been made to improve compatibility and minimise the layer seperation by the use of compatibilizer. Both filled and unfilled systems, in presence and absence of compatibilizer have been studied. Improvement in tensile properties of the blends or are observed as compared to the non-blended rubber. Different ratios of HNBR and silicone rubber are represented in this study. Blends of HNBR with silicone rubber were immiscible system. The tensile strength increased with filler loading.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.52-58
• /
• 2017

Graphene oxide (GO)/carboxylated styrene-butadiene rubber (XSBR) nanocomposites with various contents of GO were prepared by a latex compounding method. It has been confirmed that the functional groups of GO and the hydrogen bonds between GO and XSBR are existed. It can be seen that the scorch time ($t_{s2}$), which is the measurement of incipient vulcanization of rubber, showed a delay after the addition of GO. Field emission scanning electron microscopy was employed to confirm the uniform dispersion of filler in the matrix. Indeed, with increasing fillers loading, the torque, tensile strength, thermal stability and crosslink density of obtained nanocomposites were improved. These results were correlated to the better dispersion of fillers through the rubber matrix.