• Elastomers and Composites
• /
• 제28권2호
• /
• pp.103-107
• /
• 1993

To make new filler for conducting rubber, the sample of perovskite-related ferrite system $Dy_{2-x}Sr_{1+x}Fe_2O_{7-y}$ (x=0.0, 0.5, 1.0, 1.5, and 2.0) were synthesized at 1473K in air. $M{\ddot{o}}ssbauer$ spetrum of x=0.0 sample shows typical six line pattern with $M{\ddot{o}}ssbauer$ parameters, $I.S=3.6{\times}10^{-1}mm/sec,\;E_Q=-7.0{\times}10^{-2}mm/sec,\;H_{int}=5.19{\times}10^2\;Koe$. In case of x=2.0, the spectrum is composed of single line exhibiting coexistance of $Fe^{3+}(I.S.=3.7{\times}10^{-1}mm/sec)$ ions and $Fe^{4+}(I.S.=-1.9{\times}10^{-1}mm/sec)$ ions. With increase in x value electrical conductivity at constant temperature sharply increased and the activation energies decreased from $3.8{\times}10^{-1}\;to\;1.9{\times}10^{-1}\;eV$.

• Elastomers and Composites
• /
• 제30권1호
• /
• pp.20-31
• /
• 1995

The purpose of this study is to investigate the reinforcement of inorganic filler silica, treated by MDI about SBR vulcanizate. The characteristics of vulcanization, physical properties, surface properties and dynamic properties were investigated after mixing those silica with SBR and unmodified silica with SBR. In this experiment only the quantity of silica was variable. In the vulcanization characteristics tested by rheometer, S-series showed the fastest scorch $time(t_{10})$ and optimum cure $time(t_{90})$. And in test or tensile characteristics hardness, tensile strength, 100%, 300% modulus and elongation were all appeared in the order of M>S-series. The characteristic bonding of urea between unmodified silica and MDI could be confirmed in IR spectrum. The shapes of silicas treated chemically were observed by SEM. And the dispersion of the filler in the SBR composite was uniform. In the dynamic characteristics by the RDS, the order of elastic modulus G' values was as follows : M>S-series, and also the order of damping values was as follows : M>S-series.

• Macromolecular Research
• /
• 제9권2호
• /
• pp.92-99
• /
• 2001

Silica-filled rubber compounds have slower cure characteristics than carbon black-filled ones due to the adsorption of curatives on the silica surface. Fatty acid was used as a cure activator along with zinc oxide in a sulfur cure system. Poly(ethylene glycol), PEG, was used in silica-filled rubber compounds to prevent adsorption of the curatives on the silica surface. In this study, influence of the size of fatty acid and PEG on properties of silica-filled NR compounds was investigated. It was found that the size of fatty acid and PEG affected the curt: characteristics and physical properties. The cure rate becomes faster as the PEG size increases. By increasing the size of fatty acid or PEG, the delta torque of the compound decreases while the Mooney viscosity increases. The modulus of the vulcanizate decreases with increasing the molecular weight of fatty acid or PEG. The experimental results were explained by the filler dispersion and by the prevention of the curative-adsorption on the silica surface.

• Carbon letters
• /
• 제1권3_4호
• /
• pp.138-142
• /
• 2001

The effect of electrochemical surface treatments in KOH chemical solution on microstructures of carbon blacks was investigated in terms of surface functional values and XRD measurements. And their mechanical interfacial properties of the carbon blacks/rubber composites were studied by the composite tearing energy ($G_{IIIC}$). It was found that the development of basic-surface functional groups lead to the significant physical changes of carbon blacks, such as, decrease of the interlayer spacing ($d_{002}$), increase of the crystalline size along c-axis ($L_c$), and increase of degree of crystalline (${\chi}_c$). This treatment is possibly suitable for carbon blacks to be incorporated in a hydrocarbon rubber matrix, resulting in improving the hardness and tearing energy of the resulting composites.

• 한국전기전자재료학회논문지
• /
• 제25권9호
• /
• pp.732-737
• /
• 2012

This study made a specimen (contact surface size: $45\;mm{\times}0.02\;mm{\times}45{\sim}55\;mm$) with silicon rubber for low voltage cable with 50 phr silica filler. The electrification voltage of electrostatics were measured for different sizes of contact surface with the applied voltage of 10kV and the environmental settings of temperature ($25{\sim}40^{\circ}C$) and humidity (40~80%). The following conclusions were made. The electrification voltage of electrostatics decreased as the humidity increased. The electrification voltage of electrostatics increased as the temperature increased. The larger the surface size, the higher the electrification voltage of electrostatics. The property of the material had more effect on the relaxation time than the humidity.

• 한국산업융합학회 논문집
• /
• 제2권1호
• /
• pp.69-75
• /
• 1999

Intending to develop a new rubber curing process using only microwave, the both the characteristics of cure and the mechanical properties of rubbers for the tire tread, for which a green styrene-butadiene compounds had been cured with 2.45 GHz microwave, have been compared with those of the custom thermal cured rubber. The unintentional hot spot formation in the compound during the microwave curing has not found where the compound has a microwave absorbing ceramic powders in 4.18 weight percents and the supplying voltage has been adjusted to 90 volts. The new microwave process accomplished preheating to 418K in a quarter of the thermal cure time. The average tensile strength of the microwave-cured rubber indicating $190kg/cm^3$ was compatible to that of the thermal cure. In conclusion, the new microwave cure had approved to be applicable in a commercial plant.

• Computers and Concrete
• /
• 제11권1호
• /
• pp.63-73
• /
• 2013

In this study, the effect of reducing cement by proportional addition of waste powder rubber on the performance of concrete under impact three-point bending loading were investigated experimentally and numerically. Concrete specimens were prepared by adding 5%, 10% and 20 % of rubber powder as filler to the mix and decreasing the same percentage of cement. For each case, three beams of $50mm{\times}100mm{\times}500mm$ were loaded to failure in a drop-weight impact machine by subjecting them to 20 N weight from 300mm height, while another three similar beams were tested under static load. The bending load-displacement behavior was analyzed for the plain and rubberized specimens, under static and impact loads. A three dimensional finite-element method simulation was also performed by using LUSAS V.14 in order to study the impact load-displacement behavior, and the predictions were validated with the experimental results. It was observed that, despite decreasing the cement content, the proportional addition of powder rubber until 10% could yield enhancements in impact tup, inertial load and bending load.

• 한국재료학회지
• /
• 제9권4호
• /
• pp.409-413
• /
• 1999

Recently, the polymeric insulators have been accepted in several countries for the outdoor high voltage applications. In comparison with the conventional porcelain, polymeric insulators offer various advantages such as light weight, superior vandal resistance and better contamination performance. The outdoor polymeric insulating materials such as silicone rubber, ethylene propylene diene monomer(EPDM), ethylene vinyl acetate(EVA) and epoxy are aged such as silicone rubber, ethylene propylene diene monomer(EPDM), ethylene vinyl acetate(EVA) and epoxy are aged under the various natural environment with the long-term performance in outdoor. In this paper, the effects of UV-under the various natural environment with the long-term performance in outdoor. In this paper, the effects of UV-ray on the surface of silicone rubber were investigated by using the weather-Ometer. The accelerated aging stresses were simulated by UV radiation, high temperature and humidity as well as water spray. These aging characteristics were examined through contact angle measurements, tracking resistance test, FT-IR and SEM/EDS analysis. The experimental results showed that tracking resistance decreases with increase in the UV-ray irradiation period. But the surface of silicone rubber kept hydrophobicity. It is found that the inorganic filler such as)$ Al(OH_3$ improves tracking resistance and the $Tio_2$is very effective in preventing degradation of silicone rubber surface from UV-ray.

• Elastomers and Composites
• /
• 제41권3호
• /
• pp.157-163
• /
• 2006

침전실리카와 친수성 및 소수성 흄실리카를 사용하여 첨가량에 따른 실리콘 고무인상재의 젖음성과 기계적 물성 향상 연구를 수행하였다. 고무인상재의 경화시간에는 흄실리카 종류보다는 입자크기가 영향을 미쳤으며, 입자크기가 가장 작은 A300을 사용할 경우 약 9분 정도의 경화시간 지연을 초래하였다. 소수성 흄실리카인 R972를 대체 사용할 경우 고무인상재의 젖음성 특성이 가장 우수하였다. 침전실리카와 A300 흄실리카를 85:15로 혼합하여 사용할 경우 인열강도가 약 1.5N/mm 정도 증가하지만 경화시간의 과도한 지연과 더불어 점도가 상승하기 때문에, 흐름성 및 기계적물성 측면에서 침전실리카와 흄실리가(A300)를 90:10으로 혼합하여 사용하는 것이 최적이었다.

• 한국안전학회지
• /
• 제20권3호
• /
• pp.58-63
• /
• 2005

In this research, silicone rubber with additions of inorganic filler, alumina trihydrate$(Al(OH)_3\;:\;ATH)$, was aged acceleratedly and cyclically by the salt-fog and heating. The optimum amount of ATH addition to silicone rubber have been investigated by measurements of leakage current in the change of electrical properties and tensile strength, %elongation in mechanical properties and FT-IR, TG, SEM in the change of the chemical properties. With regard to un-aged silicone rubber, as the ATH addition amount increases, conductive path formation time was shortened in the electrical properties and tensile strength was increased, %elongation was decreased. In case of identical ATH addition amount, as cyclic aging increases, surface resistivity, tensile strength and %elongation were decreased. Considering the cyclic aging, the most effective amount of ATH addition was about 90phr.