• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.992-998
• /
• 2004

During the tube hydropiercing, the region adjacent to the pierced hole will be deformed and will be drawn away from the die block as the punch advances through the wall of the tube. The deformation in the region may range from a substantially flat form to a countersunk form, so called rollover. In this study, the effects of material properties, shape of piercing punches, roundness of tube surface and internal pressure within the tube during piercing on the rollover have been investigated experimentally. The results provide the quantitative variation of rollover at given hydropiercing parameters, and a relationship between the deformed radius and the rollover caused by the deformation has been established.

• 한국공작기계학회논문집
• /
• 제10권1호
• /
• pp.71-77
• /
• 2001

Experimental study if die-sinking electrical discharge machining(EDM) was conducted with rotating electrode system including inside hole for increasing the material removal rate(MRR). With the help of dielectric fluid flow through the inside according to the different internal diameter of the hole, the molten workpiece debris could be removed and flushed out during the EDM, Cold die alloy(SKD-1) was executed for different peak current and duty factor. From this study, the MRR was found to be increased with the peak current. The more MRR was obtained for the case of electrode inside diam-eter of 10 mm, but the MRR was decreased as the diameter near at the 4mm and 6mm. The values of surface roughness and roundness were analyzed under various conditions, and these were affected by the inside diameter change of electrode.

• 한국레이저가공학회지
• /
• 제11권1호
• /
• pp.25-31
• /
• 2008

The characteristics of femtosecond laser ablation of $Al_2O_3$ for prescision microfabrication are studied experimentally. Specifically, the process time during femtosecond laser drilling of microholes with $sub-100{\mu}m$ diameter are investigated for varying laser fluence, scan speed and beam path designs like trepanning with continuously changed start points. The accumulation of sub-micrometer size particles within the hole and the deterioration of edge clarity and roundness for decreasing hole diameter are examined and through process optimization the microdrilling with good hole quality is achieved using a femtosecond laser system (repetitionrate 1 kHz, wavelength 785 nm, pulse duration 185 fs)

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제23회 학술대회
• /
• pp.76-82
• /
• 1996

This paper was undertaken to analyze the morphology of wear debris generating from moving lubricated machine surfaces by image processing. The lubricating wear test was carried out under different experimental conditions using the wear test device was made in our laboritory and wear testing specimen of the pin on disk type wear rubbed in paraffine series base oil, by varying applied load, sliding distance. The four parameters(50% volumetric diameter, aspect, roundness and reflectivity) to describe the morphology have been developed and are outlined in the paper. A system using such techniques promises to obviate the need for subjective, human interpretation of particle morphology in machine condition monitoring, thus overcoming many of the difficulties with current methods and facilitating wider use of wear particle analysis in machine condition monitoring.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.135-144
• /
• 1997

This wear debris can be harvested from the lubricants of operating machinery and its morphology is directly related to the damage to the interacting surfaces from which the particles originated. The morphologies of the wear particles are therefore directly indica- rive of wear processes occuring in machinery and their severity. The neural network was applied to identify wear debris generated from the lubricated moving system. The four parameter(50% volumetric diameter, aspect, roundness and reflectivity) of wear debris are used as inputs to the network and learned the friction condition of five values(material 3, applied load 1, sliding distance 1). It is shown that identification results depend on the ranges of these shape parameter learned. The three kinds of the wear debris had a different pattern characteristic and recognized the friction condition and materials very well by neural network. We dicuss how the network determines difference in wear debris feature, and this approach can be applied to condition diagnosis of the lubricated moving system.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.343-349
• /
• 1998

A modeling of machined geometry and cutting force was proposed for the case of round shape machining, and the effects of internally machined profile are analyzed and its realiability was verified by the experiments of roundness tester, especially in boring operation in lathe. Also, harmonic cutting force model was proposed with the parameter of specific cutting force, chip width and chip thickness, and in this study, we can see that bored workpiece profile was also mapped into cutting force signal with this model. In general, we can calculated the theoretical lobe profile with arbitrary multilobe. But in real experiments, the most frequently measured numbers are 3 and 5 lobe profile in experiments. With this results, we can predict that these results may be applied to round shape machining such as drilling, boring, ball screw and internal grinding operation with the same method.

• 대한기계학회논문집
• /
• 제17권11호
• /
• pp.2723-2729
• /
• 1993

Moire principles are applied to the measurement of the spindle radial error motion. As opposed to conventional techniques, no master cylinder or ball is needed in the measurement so that the offset and out-of-roundness errors of the master can be inherently eliminated. Two periodic circular gratings are used, one is made on the spindle and the other is held stationary on the reference frame. When the two gratings are seen superimposed during spindle rotation, an interference fringe pattern is observed from which the information on the eccentricity between the two gratings can be extracted with high precision. The optical design and fringe analysis techniques of a prototype measurement system are described in detail with exemplary measurement results.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.285-290
• /
• 2000

This paper was undertaken to do morphological analysis of wear debris for slipper-pad of hydrauric rotary acuator. The lubricating wear test was performed under different experimental conditions using the wear test device and wear specimens of the pin on disk type was rubbed in paraffinic base oil by three kinds of lubricating materials. varying applied load, sliding distance. The four shape parameters(50% volumetric diameter, aspect, roundness and reflectivity) are used showed that the four shape parameters of wear debris depend on a kind of the lubricating condition. It was capable of presuming wear volume for slipper-pad of hydrauric rotary acuator on driving time.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.240-245
• /
• 2000

This paper presents the experimental study of drilling for duralumin A2024 with intermittently decelerated feed rate. It is achieved through a programmed periodic increase and decrease in the feed rate using a machining center. The following experimental result were performed with the objective of solving chip to disposal problems. In conventional drilling of aluminum, long continuous chips are produced that wind around the drill causing difficulties in eliminating chips from the cutting zone. In order to acquire the basic data necessary to regulate the chip profile, the relationship between cutting variables and chip shape was investigated. The following conclusions are established from the experimental results. At a suitable feed fluctuation ratio, intermittently decelerated feed drilling proved successful in breaking chips to appropriate lengths while maintaining stable cutting. Thus, it is an effective method for improving chip disposal. The amplitude of the dynamic component of cutting force in intermittent feed frilling is influenced by the feed fluctuation ratio.

• 한국CDE학회논문집
• /
• 제20권4호
• /
• pp.412-419
• /
• 2015

This paper presents the results of the structural analysis and the optimization of a 6,500 m manned submersible. Nonlinear structural analysis for imperfect spheres with the maximum allowable out-of-roundness(OOR) was performed to calculate the thickness of the pressure hull. Dimensions of viewports were determined according to ASME PVHO standard. The design optimization of the spherical hull with openings was divided into two steps - the optimization of the detailed shape of the viewport reinforcements and the optimization of the viewport location in the spherical pressure hull.