• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.223-225
• /
• 2007

Online models predicting roll force and forward slip of roughing mill was developed using nondimensional parameters. Using the effective inlet thickness, roll force model take into account the effect of inlet dog-bone shape of slab which take places after width reduction through edger rolling in roughing mill. The prediction accuracy of the proposed model is examined through comparison with measurements.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.13-16
• /
• 2000

In the hot strip mill, a bad threading and shape of strip strip in the finishing mill was caused by asymmetric rolling In roughing min. Mathematical analysis for camber control of roughing mill in hot strip rolling has been developed. Each equation in the camber control model was derived from geometrical characteristics of camber mechanism. The model can predict variables such as wedge, side slippage and roll force difference etc. from a measured camber value and then find an optimum roll gap condition for minimizing camber in the next pass.

• 소성∙가공
• /
• 제8권2호
• /
• pp.200-207
• /
• 1999

To increase dimensional accuracy of strip width, model to compensate width spread during roughing mill has been developed. To measure the amount of width spread during the production rolling more precisely, special roughing rolling procedures for the horizontal rolling and dog-bone rolling were designed in the actual production mill. From the operational data analysis, it is known that the prime factors influencing on the width spread were strip width, strip thickness, edging amount, number of pass and type of edger roll etc., Based upon the statistical analysis of rolling data, new models which can predict width spread during horizontal rolling and dog-bone rolling were developed and tested on the actual processing conditions for the reliability. The application test showed that newly developed model gave fairly accurate predictions on the width spread during roughing passes.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.544-548
• /
• 2007

In general, final width of hot strip should be accomplished in this stage because width reduction of strip hardly appears during typical finishing mill. However, it is difficult to control the width of strip in the roughing mill process as the horizontal rolling of strip is subsequently performed after the vertical rolling. It is therefore important to obtain the deformation rolling direction on strip width to minimize the width spread of strip during horizontal rolling after vertical rolling. Generally there is Sizing press type and Edger-roll type. The width reduction process in sizing press has small amount of width spread compared with the edger. However, productivity by the sizing press process is much lower than those of the edger. In this study, sizing press and Edger-roll process parameters in a sheet rolling mill were set at specified values and the effect of the change in these parameters on product quality and process performance were evaluated.

• 대한기계학회논문집
• /
• 제16권4호
• /
• pp.819-827
• /
• 1992

본 연구에서는 전술한 바와 같은 반복되는 압연부하에 의한 롤의 피로특성을 규명하기 위해 열연공장의 조압연기중 표본작업 롤의 피로특성을 규명하기 위해 열연 공장의 조압연기중 표본 작업 롤을 선정하고 일정기간의 사용이력을 조사하였으며, 이 를 토대로 롤내부 온도 및 열응력 계산을 수행하여 압연중 발생되는 피로 균열의 크기 를 정량화 시켜보았다. 또 표면 균열관찰 실험 및 롤 표면흠 대응 실험을 통해 피로 균열이 압연판의 표면품질에 어떠한 영향을 미치는지 조사해보았다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.297-298
• /
• 2007

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.134-137
• /
• 2001

In this paper on-line model is derived from investigating via series of finite element process simulation. Some variables that little affect on non-dimensional parameters. ie. forward slip and torque factor. is extracted from composing on-line model Especially, this research focused on deriving on-line model which exactly predict roll force and roll power in the roughing mill process under small shape factor and small reduction ratio. The prediction accuracy of the proposed model is examined through comparison with predictions from a finite element process model

• 소성∙가공
• /
• 제23권3호
• /
• pp.139-144
• /
• 2014

In the current study, we present a new model for predicting width spread of a slab with a dog-bone shaped cross section during rolling in the roughing train of a hot strip mill. The approach is based on the extremum principle for a rigid plastic material and a three dimensional admissible velocity field. The upper bound theorem is used for calculating the width spread of the slab. The prediction accuracy of the proposed model is examined through comparison with the predictions from 3-D finite element (FE) process simulations.

• 한국정밀공학회지
• /
• 제24권7호
• /
• pp.60-68
• /
• 2007

This paper presents an efficient 5-axis roughing method for centrifugal impeller. The efficient roughing is minimization of cutting time through minimizing tool tilting and rotating motions. To minimized cutting time, machining area is divided into sub-cutting regions using control points on hub curves and shroud curves of blade used to design and analyze centrifugal impeller. For sub-cutting regions, diameters of cutting tools are determined as big as possible. Then, tool paths are generated with the tilting axis and rotating axis of 5-axis machine limited and fixed, which can give more efficient machining speed and machining stability than the conventional methods. Experimental results show that the proposed method is more efficient than the conventional methods to mill with the only one cutting tool without dividing area and the previous methods to mill with simultaneous 5-axis processing with dividing area.

• 소성∙가공
• /
• 제9권1호
• /
• pp.66-71
• /
• 2000

The present study tackles the metallurgical subjects involving the thin slab-direct hot rolling process, i.e. mini-mill process. In order to clarify the effect of chemical composition of steel and MnS precipitation behaviors on the development of edge cracking during hot rolling, the content of manganese and sulfur in low carbon steel was varied and the isothermal treatment prior to roughing was applied. Edge cracking during roughing in the hot-rolling process of mini-mill was effectively prevented by means of the isothermal treatment at 115$0^{\circ}C$ for 5 minutes in the 0.4% manganese steel containing sulfur lower than 0.013%. With the increase in manganese content in low carbon steel, coarser MnS developed. The edge cracking index which denotes the total length of edge crack per unit edge-length of rolled specimens was proposed in this paper. It was found that the edge cracking index linearly decreased with the increase in the ratio of MnS.