• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.5
• /
• pp.281-294
• /
• 2015

In order to quantitatively estimate the nonlinear destructive interaction of wave load with wind load, which is very vital for the optimal design of offshore wind energy converter, we carried out a hydraulic model test and wind tunnel test. As a substructure of offshore wind energy converter, we would deploy the monopile, which is popular due to its easiness in construction. Based on the simulation using Monte Carlo simulation using Kaimal spectrum and cross spectrum, the instantaneous maximum wind velocity is adjusted to 10 m/s. And, considering the wave conditions of the Western Sea where a pilot wind farm is planned to be constructed, $H_s=0.1m$, 0.15 m, 0.2 m is carefully chosen. It turns out that the nonlinear destructive interaction between the wind and wave loads acting on the offshore wind energy converter is more clearly visible at rough seas rather than at mild seas, which strongly support our deduction that a Large eddy, a swirling vortex developed near the bumpy water surface in the opposite direction of the wind, is the driving mechanism underlying nonlinear destructive interaction between the wind and wave loads.

• Journal of the Korean Vacuum Society
• /
• v.11 no.3
• /
• pp.176-182
• /
• 2002

Amorphous $TiO_2$ thin films were deposited on glass substrates by ion beam sputtering in which the ratio of $O_2$/Ar gas used as discharged gas was varied from 0 to 2. After optical and microstructure properties and chemical composition of thin films was analyzed, antireflection coating layers were fabricated with $SiO_2$/$TiO_2$ multi-layers. Thin films deposition was performed at room temperature and ion beam voltage and ion current density for sputtering of target were fixed at 1.2 kV and 200 $\mu\textrm{A}/\textrm{cm}^2$, respectively. Refractive indexs of the deposited $TiO_2$films were 2.40-2.45 at a wavelength of 633 nm. $TiO_2$films had high transmission and stoichiometry when ratio of $O_2$/Ar was 1. Rms roughness of deposited $TiO_2$ film was below 7 $\AA$. In excessive $O_2$ environments, however Rms roughness increased over 50 $\AA$. Transmittance decreased by scattering of rough surface. Reflectance of $SiO_2$/$TiO_2$multi-layers was below 1% in visible light.

• Journal of the Korean Magnetics Society
• /
• v.10 no.1
• /
• pp.30-36
• /
• 2000

SmCo films were deposited on Si(100) substrate by a Nd-YAG pulsed laser ablation of the targets of Sm$\_$100-x/Co$\_$x/ (73$\leq$x$\leq$93) at the substrate temperature of 600∼700$\^{C}$ and the laser beam energy density of Q switching mode or fixed Q mode. The magnetic properties of the films obtained from the Q switching mode exhibited a 4 $\pi$ Ms of 5200∼7700 Gauss, iHc of 190-250 Oe, and 4$\pi$M$\_$r//4$\pi$M$\_$s/ of 0.4∼0.74, respectively, while the fixed Q mode gave the magnetic properties of corresponding films of a 4$\pi$M$\_$r//4$\pi$M$\_$s/ = 0.32∼0.91 and iHc of 430-6290 Oe, respectively. The fixed Q mode gave the better magnetic properties of the SmCo films which seems to be due to a formation of magnetically hard minor phases in droplet of Sm-rich intermetallics. However, the resultant rough surface of the SmCo films is a problem to be solved by a continued study.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.3
• /
• pp.3-15
• /
• 1986

This study was carried out to investigate the drying rate and drying defects of Populus euramericana using the SDR (Saw-Dry-Rip) process. Flitches for SDR process were rough edged for compact kiln stacking, and then kiln-dried to 10 percent moisture content with dimensions in the same run, using the kiln-drying schedule ($T_8-F_4$) recommended by Rasmussen. The results obtained were as follows: 1. Drying rate of dimensions was slower than that of flitches. 2. Final moisture content and moisture distribution of dimensions were lower than those of flitches. 3. Average bowing, cupping, crooking, and twisting were reduced 20 percent, 25 percent, 54.9 percent, and 13.4 percent by SDR process respectively. 4. Bowing and cupping were more severe in dimensions from the area near the pith than in those from the area near the bark, and for crooking and twisting the reverse was true. 5. Surface checking of dimensions developed less than that of flitches and end checking of dimensions was similar to that of flitches. 6. Honeycomb, thickness shrinkage, and collapse of dimensions were similar to those of flitches. 7. The degree of casehardening of dimensions was higher than that of flitches.

• Korean Journal of Microbiology
• /
• v.37 no.2
• /
• pp.130-136
• /
• 2001

The killing effects of two types(one-phase reactor and two-phase reactor) of UV-TiO$_2$photocatalytic system on the microorganisms have been studied. The UV-lamp which emits maximum 39 watts at 254 nm was prepared in these system. Three types of $TiO_2$ coating method were adopted. One type is thin film coated form on the quartz tube in the reactor and another one is surface rough coated form on the glass bead. The other one is $TiO_2$-mixed alginate bead form. UV irradiation was carried out for 1 min. In case of one phase reactor, the bactericidal efficiencies of E. coli by $TiO_2$-coated quartz tube and $TiO_2$-coated glass bead were 63.2% and 89.9%, respectively. In the air-bubbling system, the bactericidal efficiency was 95%, however, the efficiency decreased to 90.6% in the non-bubbling system. In the $TiO_2$-mixed alginate bead system, bactericidal efficiency was 86%. When $H_2O$$_2$ was treated (10, 15, 20, and 25 mg/ι) to the $TiO_2$-coated glass bead reactor, bactericidal efficiency significantly increased according to the concentration of $H_2$$O_2$. Two phase reactor showed more elevated efficiency. E. coli was more sensitive to the reaction than S. cerevisiae.

• Korean Journal of Food Science and Technology
• /
• v.46 no.2
• /
• pp.165-172
• /
• 2014

Mixed fermentation of cow milk was performed by sequential co-cultures with Bacillus subtilis and Lactococcus lactis. After a first fermentation step with B. subtilis for 6 h, the number of viable cells increased to $2.5{\times}10^8$ CFU/mL. The second fermentation step with L. lactis resulted in increased viable cells $1.09{\times}10^{10}$ CFU/mL for 3 days and increased acidity. However, the number of viable B. subtilis cells was decreased greatly to $5{\times}10^1$ CFU/mL following fermentation with L. lactis. Milk proteins were markedly hydrolyzed by the first fermentation after 2 h, and the second fermentation induced curd formation in milk. However, after 4 h, the first fermentation resulted in higher whey separation and 80 mg% tyrosine content. Gamma-aminobutyric acid (GABA) production was dependent upon the degree of protein hydrolysis by first fermentation. Second fermentation resulted in 0.14% GABA. The milk fermented by B. subtilis indicated the rough surface of yogurt depended upon the degree of protein hydrolysis. In conclusion, set-type yogurt was efficiently produced by co-culturing of milk, and fortifying with peptides, GABA, and probiotics.

• Journal of Biosystems Engineering
• /
• v.3 no.2
• /
• pp.114-125
• /
• 1978

The use of petroleum fuels in grain drying causes problems of high cost and management. To solve these problems, it is required to study on soLar energy as an alternative to petroleum fuels for grain drying. The purposes of this study were to find out the optimum received area and air flow rate of a flat-plate solar air collector for grain drying and to assess its effects on grain drying with a small grain bin. The results of this study are summarized as follows ; 1. The calculated optimum tilt angles of the collector in the summer and autumn drying seasons were 20 and 50 degress, respectively, in suwon area. 2. The outlet temperature of the collector was $36^\circ C$ on the daily average with the maximum of $36^\circ C$ at 12:00 o clock. Solar radiation on the collector surface was 1.04 ly( 1 langley = 1 cal/$cm^2$) per minute on the daily average and 1.30 ly per minute on the maximum at 11:00am. The thermal efficiency of the collector was 62.4 percent on the daily average, and the air flow-rate per unit receiving are was 1.03 $m^3$/min/$m^2$.4. The calculated optimum receiving area and the air flow-rate per unit cubic volume for paddy in autumn drying season was 2 $m^2$ and 2$m^3$/min , respectively. 5. not significantly difference in the collector efficiency was appeared between the rotating and fixed type of solar collector. 6. For drying of wheat with 0.6 meter of the depth in the bin, approximately 9 hours were required to reduce the moisture content from 21.6% to 13% with air follow rate of 5 $m^3$/min an initial moisture per cubic meter of wheat and with air temperature of $52^\circ C$. 7. In the drying test of rough rice with a turning operation in a grain bin approximately 21 hours were required to reduced the moisture from 21% to 14.5% with airflow rate of 2 $m^3$/min per cubic meter of rice and the air temperature of $43.5^\circ C$. 8. Over-drying at the bottom and less -drying at the top of the grain mass was resulted from the high -temperature of drying air which was obtained from the flat-plate solar collector in this test. An appropriate operation should be prepared for the uniform moisture of the grain in the bin.

• Applied Microscopy
• /
• v.12 no.2
• /
• pp.11-22
• /
• 1982

The morphological development of Mycoplasma pneumoniae attached to solid surfaces was examined by light and electron microscopies. Critical point drying and carbon replication techniques revealed that during the growth cycle of developing microcolonies, the morphological form coincided with the pH of the culture. M. pneumoniae appeared to have a well defined morphology associated with age of the culture. The organisms were dimorphic, with round cells capable of reproduction and segments consisting of a spindle shaped body with one pointed and one knob-like end. Starting with single cells, there were the following stages in the development of a culture: replication stage through binary fission and segmentation, stage of confluency, and a degeneration stage into rough spherical forms. The round cells appearrd to replicate by binary fission during the lag and early log phases of growth, while spindle segments replicated by segmentation during most of the logarithmic growth. The growth of the filaments and replication of the segments occured at the knob-like ends, showing a type of polarity, and formed a meshwork across the surface. This development could be cycled under favorable growth conditions, but the culture aged and when the conditions became adverse(e.g. pH 6.8 or lower), filamentous cells converted to spherical forms, losing their reproductive capability.

• Applied Microscopy
• /
• v.32 no.3
• /
• pp.213-222
• /
• 2002

Histology and ultrastructure of the mantle epidermis in the ark shell, Scapharca broughtonii are described using light and electron microscopy. The mantle of the ark shell is composed of outer epidermis, connective tissue and inner epidermis. Both epidermis are simple and consists of supporting cells, ciliated cells and secretory cells. Connective tissue is composed of mainly collagen and muscle fibers. The supporting cells in the inner epidermis are usually columnar and covered with microvilli. The ciliated cell have cilia and microvilli on the free surface, and numerous tubular mitochondria are observed in the apical cytoplasm. Secretory cells are mainly observed in the outer epidermis, and it can be divided into four types of A, B, C and D with morphological features of the secretory granules. Type A cells of mucous cell are found in the marginal and central mantle. And these cells contains numerous secretory granules of non-bounded and low electron density. Type B cells contains numerous rough endoplasmic reticula, well-developed Golgi complex and secretory granules of membrane-bounded and high electron density. Secretory granules of type C cells are divided into fibrous core layer and homogeneous peripheral layer. Type D cells are found in the outer epidermis of the central and umbonal mantle. And secretory granules of these cells are divided into homogeneous core layer and granular peripheral layer. This results suggest that the outer and inner epidermis of the mantle are related with shell formation and cleaning of the mantle cavity, respectively.

• Korean Journal of Food Science and Technology
• /
• v.30 no.1
• /
• pp.42-48
• /
• 1998

Physicochemical properties of waxy maize starch and oxidized waxy maize starch with sodium hypochlorite $(0{\sim}60\;mg\;CL_2/g\;starch,40^{\circ}C,\;pH\;10,\;3.0\;hr)$ were studied. As sodium hypochlorite concentration was increased, the content of crude lipid and crude protein of the oxidized starch were decreased. And crude protein content and whiteness was considered to show negative regression. However, the crude ash content of the oxidized starch increased significantly with oxidation and bore a positive regression to the chlorine content. There was a progressive increase in the carboxyl content with increasing oxidant level. After pasting in hot water and cooling, viscosity of the oxidized starches were drastically lower than that of native starch . As carboxyl contents of the oxidized starch increased, the solubility and swelling power was increased. When waxy maize starch treated with 0, 1.5, 3.0 and 6.0% sodium hypochlorite, temperature of initial gelatinization of oxidized starch was shown to 65, 65, 60 and $50^{\circ}C$, respectively. The oxidized waxy maize starches also form clearer pastes. Water binding capacity of the oxidized starch decreased as the degree of carboxyl group substitution increased. Waxy maize starch has polygonal and some round granules which range from about 3.7 to $20\;{\mu}m$ in diameter. Surface appearance of the waxy maize starch became rough when oxidized with sodium hypochlorite. When homogenate of the oxidized waxy maize starch solution and corn germ oil was stored under room temperature for 24 hours, the emulsion stability was considered to depend on starch concentration and degree of substitution.