• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.297-301
• /
• 2007

초음속 충동형 터빈과 같이 종횡비가 작은 경우 로터 익형은 반경방향으로 동일한 단면을 갖는 형태로 구현된다. 이 경우 터빈 로터는 터빈 동익의 프로파일 직경에 따라 설계에서 의도하지 않은 유로면적분포와 터빈 성능의 차이를 보인다. 본 연구에서는 터빈 동익 프로파일을 정의하는 직경이 터빈 성능에 미치는 영향을 고찰하기 위하여 3개의 다른 위치에서 정의된 터빈 로터에 대한 유동해석을 수행하고 결과를 고찰하였다. 계산 결과 팁에서 단면이 정의된 경우 설계에서 의도한 유로면적 변화를 보이며 다른 프로파일 직경에서 정의된 터빈에 비해 우수한 성능을 보임을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.418-423
• /
• 2003

The balancing performance of an automatic ball balancer (ABB) in the vertical or horizontal position is studied in this paper. Considering the effects of gravity and angular velocity profiles, a physical model for an ABB installed on the Jeffcott rotor is adopted. The non-linear equations of motion for the rotor with ABB are derived by using Lagrange's equation. Based on derived equations, dynamic responses for the rotor are computed by using the generalized-u method. From the computed responses, the effects of gravity and angular velocity profiles on the balancing performance are investigated. It is found that the rotor with ABB can be balanced regardless of the gravity effect. It is also shown that a smooth velocity profile yields relatively smaller vibration amplitude than a non-smooth velocity profile.

• 대한기계학회논문집A
• /
• 제21권1호
• /
• pp.45-52
• /
• 1997

In this study, we designed tooth profile of the fly-cutter for antisymmetric rotor which is used in screw compressor. In order to verify this profile, we manufactured three different pairs(J46, N46, P46) of antisymmetric rotor using fly-cutter. We got the following conclusions from this study. (1) We obtained better contact condition using 3pairs of rotor which are manufactured by the fly-cutter. (2) We could prevent the cutter interference near bottom point of the robe of screw rotor.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.923-928
• /
• 2007

The rattle noise originated from the oil-pump system was issued in developing an engine. In this paper, the major concerning factors for rattle noise are analyzed and the NVH developing process is summarized. The main factors are the tip clearance of inner/outer rotor, the clearance between oil pump housing and rotor guide and the rotor mass. Also, the optimization for oil-pump rotor whine noise is performed. The main factors of the rotor whine are the profile of the rotor, the oil pressure and the shape of oil route. This paper will present the design guidelines of the engine oil-pump system.

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.511-516
• /
• 2004

The dynamic behavior of an automatic ball balancer (ABB) is studied considering the effects of gravity and angular velocity profiles. In this study, a physical model for an ABB installed on the Jeffcott rotor is adopted in order to investigate the effects of gravity and angular acceleration. The equations of motion for the rotor with ABB are derived by using Lagrange's equation. Based on derived equations, dynamic responses for the rotor are computed by using the generalized-o method. From the computed responses, the effects of gravity and angular velocity profiles on the dynamic behavior are investigated. It is found that the balancing of the rotor with ABB can be achieved regardless of gravity. It Is also shown that a smooth velocity profile yields relatively smaller vibration amplitude than a non-smooth velocity profile.

• Journal of Biosystems Engineering
• /
• 제33권5호
• /
• pp.289-295
• /
• 2008

The task of chemical spraying has been seriously considered as an irritating and annoying job for Korean rice farmers. An agricultural unmanned helicopter was suggested to solve this problem so as the farmers to have more decent farming condition. The objectives of this study were to analyze the adoptability of an experimental rotor blade (SW05) using the CFD simulation and also to compare the simulation results with experimental results. The simulation results showed that the induced power of this rotor reached to $57{\sim}63%$ of total power and the profile power was about $37{\sim}43%$ of total power. Therefore it can be concluded that this rotor's performance characteristics were not so efficient for the size of unmanned helicopter due to the low induced power and high profile power relatively compared with ones of conventional rotors. The comparison with experimental results showed that the tested lifts were less than 70% of simulated ones at the grip pitch of $12^{\circ}$ and decreased to 40% at the $18^{\circ}$ grip pitch. Therefore, it can be concluded that the rotor was too oversized to be used for a 15.4 kW (21 PS) engine.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.901-902
• /
• 2010

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.119-126
• /
• 2006

Gerotor hydraulic motor is widely used in hydraulic systems due to its low speed, high torque output and compactness in rotational direct driving of a heavy weight. Gerotor is a Planar mechanism consisted of a pair of rotor and circular teeth of stator assembly which forms a closed space, so called a chamber. The motion of rotor relative to the circular tooth is produced by the pressure difference of hydraulic operating fluid between the adjacent chamber. As all active contact points of rotor and circular teeth are subjected to very high sliding friction, a reduction in the performance of the gerotor hydraulic motor can not be avoided. Therefore, the core design parameters of gerotor profile used in hydraulic motors is to minimize a friction force by high contact stresses. The analytical design method of gerotor profile, based on envelope of a family of curves, is proposed. In this study, the influence of the tip clearances on three critical contact points between rotor and circular teeth of stator assembly has been explored by experimental data in this paper. At the same time a improvement method to reduce the friction force is proposed and the tip clearances on three critical points for getting an optimum gerotor profile are also analyzed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1285-1288
• /
• 2005

Screw rotors, the key parts of screw compressors, are used in compressing air and refrigerant due to their high productivity, compact size, low noise and maintenance. In general, a screw compressor is composed of a pair of rotors of complex geometric shape. The manufacturing cost of the screw rotors is high because the complicated helical shapes of the screw rotors are manufactured usually by the dedicated machine tools. In this study, rotor profile is divided into three parts for the efficient machining. The formed tools are designed and shared for the respective split region. By cutting the screw rotor using the formed tools, this method is more efficient than the end mill in machining rotor. Experimental results show that 4-axis machining using formed tools needs less time and has the accuracy.

• 한국정밀공학회지
• /
• 제28권5호
• /
• pp.614-622
• /
• 2011

An internal lobe pump is suitable for oil hydraulics of machine tools, automotive engines, compressors, constructions and other various applications. In particular, the pump is an essential machine element of an automotive engine to feed lubricant oil. The subject of this paper is the theoretical analysis of internal lobe pump whose the main components are the rotors: usually the outer one is characterized by lobe with multiple profile(ellipse1, involute and ellipse2) shapes, while the inner rotor profile is determined as conjugate to the other. Also, the design of outer rotor depends on new applications with removing carryover phenomenon. The system generates new lobe profile and calculates automatically the flow rate and flow rate irregularity according to the lobe profile generated. In order to obtain rotor shapes in performance and to find optimize the design parameters, a Taguchi method is proposed in this paper. Results obtained from the analysis enable the designer and manufacturer of oil pump to be more efficient in this field.