• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.4
• /
• pp.261-267
• /
• 2013

In this paper, wind tunnel test and analytical prediction are compared for result of flapping motion in helicopter forward flight condition. Tests were performed at low speed wind tunnel at Chungnam National University, test section of wind tunnel has 1.8 by 1.8 meter open-jet test section area. According to the results of measured data for aerodynamic performance of model rotor in forward flight. It has to observed the difference of analytical and measured results of power coefficient for fixed thrust coefficient. And calculated and measured data of helicopter rotor flapping angles in forward flight are compared for a model rotor in a wind tunnel. A test was conducted to verify the measured data of coning and lateral/longitudinal flapping angle with predicted values.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.25 no.2
• /
• pp.63-68
• /
• 2017

In the present study, a wind tunnel test for a rotor-blade configuration was conducted to investigate a basic aerodynamic performance and a effect of the cross wind. The diameter of the configuration was 1.46 m and the test was carried out for both a clean and a tripped configurations. The boundary layer for the trip configuration was simulated by zig-zag tape and the test performed on constant-velocity and constant-rotational modes. It was shown that the test result for the tripped configuration reduces the maximum power coefficient by 9.4% ~ 12.1% compared to the clean one. Within $5^{\circ}$ of the flow angle, there is no significant loss of power, however, the coefficient is reduced by 5.3% ~ 36.7% in the range of $10^{\circ}{\sim}30^{\circ}$.

• Journal of Mechanical Science and Technology
• /
• v.20 no.4
• /
• pp.561-568
• /
• 2006

CFD simulation for one of tilt-rotor UAV configurations, TR-E2S1, was performed to investigate its aerodynamic characteristics. Control surfaces such as elevator and rudder were deflected and wing incidence angle was changed. Also aerodynamic stabilities were analyzed with the variation of pitch and yaw angles. The comparison of CFD with wind tunnel test results reveals the same trends in the aerodynamic characteristics and stabilities. However 12% scale wind tunnel test model is too small for accurate data collection and should build a high fidelity model for quantitative data comparison.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.42-46
• /
• 2005

In spite of fast growing of prediction codes, there is still not negligible uncertainty in their results. This uncertainty affects on the turbine structural design and power production prediction. With the growing size of wind turbine, reducing this uncertainty is becoming one of critical issues for high performance and efficient wind turbine design. In this respect, there are international efforts to evaluate and tune prediction codes of wind turbine. As the reference data for this purpose, field test data is not appropriate because of its uncontrollable wind characteristics and its inherent uncertainty. Wind tunnel can provide controllable wind. For this reason, NREL has done the full scale test of the 10m turbine at NASA-Ames. With this reference data, a blind comparison has been done with participation of 18 organizations with 19 modeling tools. The results were not favorable. In Europe, a similar project is going on. Nine organizations from five countries are participating in the MEXICO project to do full scale wind tunnel tests and calculation with prediction codes. In this study. these two projects were reviewed in respect of wind tunnel test and its contribution. As a conclusion, it is suggested that scale model wind tunnel tests can be a complementary tool to calculation codes which were evaluated worse than expected.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.39-44
• /
• 2005

To validate the rotor performance analysis, 3D Computational Fluid Dynamics(CFD) analysis was performed for tilt rotor aeroacoustic model(TRAM). Also, 3D vehicle with rotating rotors was simulated for rotor power effect analysis. Multiple reference frame(MRF) and sliding mesh techniques were implemented to capture the effect of rotor revolution. CFD results were compared with the wind tunnel test results to validate their accuracy. At helicopter mode, CFD analysis predicted lower thrust than the wind tunnel test but CFD results showed good agreement with the test result at cruise mode. Rotor power effect decreased the lift but did not change drag and pitching moment.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.37-40
• /
• 2006

Wind tunnel testings to develope tilt-rotor Smart Unmanned Aerial Vehicle (SUAV) were intensively performed. Small wind tunnel was used to find and evaluate design parameters and to fix general layout of configuration. The application of large tunnel with 40% scaled model is to collect performance and stability related aerodynamic data. During large scale model test wind tunnel is used as a tool to compare Flaperon types, to improve lift characteristics by using different height vortex generators and to alleviate nacelle separated flow effects on the wing.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.7
• /
• pp.497-505
• /
• 2022

Performance and hub vibratory load analyses for a lift-offset coaxial rotor are conducted using a rotorcraft comprehensive analysis code, CAMRAD II. The lift-offset coaxial rotor is trimmed to match the total rotor thrust(lift-offset coaxial rotor's thrust) or the individual rotor thrust(upper and lower rotor thrusts, respectively) in this study. The individual rotor's lift and torque, and effective rotor lift to drag ratio for the total rotor are investigated for various advance ratios and lift-offset values. The two result sets with different trim methods are similar to each other and they are correlated well with the wind-tunnel test results. Therefore, the present study using CAMRAD II validates successfully the aeromechanics modeling and analysis techniques for the lift-offset coaxial rotor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.2
• /
• pp.130-135
• /
• 2007

Wind tunnel test for Smart UAV power model has been conducted at KARI LSWT for about 3 months. The static model is used for the base plane and the power effect of tilt rotor is simulated by the tilt-rotor test rig installed in the test section. Although the genuine power effect is the difference between power-on and off tests. The existence of struts for power effect test produced unwanted form of interference and caused the change in flow angularity. To precisely evaluate power effect, a special approach is applied to Smart UAV test.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.12
• /
• pp.1599-1606
• /
• 2011

It is possible to study the load characteristics of full-scale hingeless rotor with the changing of physical smallscaled configurations such as rectangular and paddle blades, and metal and composite hubs. In this study, a static test, and a ground and wind-tunnel test were carried out using small-scale rotor models. The static test was carried out to confirm structural stiffness, characteristics of inertia, natural frequency, and damping ratio of rotors, and the ground and wind-tunnel test was carried out to confirm the stability and aerodynamic characteristics under hovering and forward flight conditions. According to the test results, the vertical load in the case of a combination of a small composite hub with paddle blades was higher than that in the case of a metal hub with paddle blades at same condition. Further, it was confirmed that the restraint of the combination of composite hub can be more flexible than the metal hub for the motion of paddle blades.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.7
• /
• pp.621-627
• /
• 2008

Aerodynamic data measured in a wind tunnel has inevitable errors due to the presence of the wind tunnel walls. These unwanted interference effects must be corrected for the wall interference free aerodynamic data. Streamline curvature effects are caused by straightening of streamlines due to wind tunnel walls. Classical Glauert's correction method that is a standard method for fixed wing aircraft is not suitable for rotary wing aircraft. In this paper, Heyson's correction method of which wake model is compatible with rotors is used to correct the rotor shaft angle as well as the dynamic pressure. The results of Heyson's method are compared with Glauert's correction method.