• 한국주거학회논문집
• /
• 제22권1호
• /
• pp.65-73
• /
• 2011

The purpose of this study is to find out the characteristics of area and spatial elements according to the building size and provide the guidelines for space planning of the child care center. This study used the content analysis method and analysis was made on the floor plans for 51 cases and the floor plans were converted to Autocad drawings to analyze the area. The results of this study were as follows; 1) Child care centers over 70% were single-attached building types which made it possible for creating outdoor environments for children. However, most small-size centers which had under 50 children did not have the facilities for outdoor activities. 2) In terms of spatial elements, the basic spaces of the small-size center were the classroom, bathroom, kitchen, office and reference room. The medium or large size centers had extra rooms for special activities and service spaces in addition to the basic spaces. 3) Classroom area per child was 2.65 m2 on average. Space composition ratio on average for care, staff, and service was programmed by 57%, 9%, 34% respectively. Small-size center had relatively more care space when compared to the others. In the case of large-size centers, there was a tendency that service space was increased, but care space was decreased.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.243.2-243.2
• /
• 2015

We report a high-performing nanoscale NiO thin film grown by thermal oxidation of sputtered Ni film. The structural, physical, optical and electrical properties of nanoscale NiO were comprehensively investigated. A quality transparent heterojunction (NiO/ZnO) was formed by large-area applicable sputtering deposition method that has an extremely low saturation current of 0.1 nA. Considerable large rectification ratio of more than 1000 was obtained for transparent heterojunction device. Mott-Schottky analyses were applied to develop the interface of NiO and ZnO by establishing energy diagrams. Nanoscale NiO has the accepter carrier concentration of the order of 1018 cm-3. Nanoscale NiO Schottky junction device properties were comprehensively studied using room temperature impedance spectroscopy.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.2005-2015
• /
• 1994

An analytical method based on the upper bound approach for the cup-bar axisymmetric combined extrusion is presented to determine the deformation zones as well as extrusion load and deformed geometry in the early stage. A new kiematically admissible velocity field is derived by the appropriate transformation of the original velocity field and applying the flow function approach. The derived velocity field is directly related to the boundary function for the plastically deforming zones and the parameter controlling the flow direction to the forward part or backward part. Experiments are carred out with the annealed aluminum 2024 at room temperature for the various area reductions. The workhardening effect is considered in the formulation as a function of the height ratio between the deformed billet and the orighinal billet to calculate the extrusion pressures. The theoretical predictions for the extrusion loads and deformed configuration are in good agreement with the experimental results.

• 한국주거학회논문집
• /
• 제18권1호
• /
• pp.11-18
• /
• 2007

At the economical crisis of Korea in 1997, self-determined price for apartment and the revision increasing the ratio of residential area for mixed-use residential building were introduced to activate the construction industry, which causes construction companies to build super high rise apartment discriminative and high class orientated. This study aims to classify the super high rise building which is planned to build or built recently and to analyze the architectural characteristics. The objects are 288 unit households in 26 apartment complexes higher than twenty five story since 1998. As a result, super high rise building comparing with existing apartments were being varied in plan types of main building and unit household and in construction types. As for the plan, the number of walls having opening to outdoor were increased and it is considered that high rise building can take advantage of a view, lighting and sunshine. The location of living room that used to be in the center of unit in existing apartment was moved freely without rule.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.319-324
• /
• 2000

Sound insulation effect of periodically arranged circular rods is studied by numerical method (BEM) and model experiment in anechoic room. Five different cylinder groups of diameter from 48 mm to 27 mm are arranged, where each group consists of 5 rows of identical rods and area ratio is kept almost the same as 60%. Comparisons of results by BEM and experiment show the band gap frequency ranges are qualitatively in agreement, while experiments gives higher attenuations. Frequency shifted attenuations (BEM results) by first group (${\phi}$48), third group (${\phi}$34) and fifth group (${\phi}$27) show that attenuation curves are in reasonable agreements for both plane wave and point source.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 금형가공 심포지엄
• /
• pp.8-18
• /
• 1998

The effect of press warm forming in cylindrical deep drawing of stainless-aluminum clad sheet metals are examined . The temperature of die and blank holder is varied from room temperature to 20$0^{\circ}C$, while the punch is kept cooled during test to increase the fracture strength of workpiece on the punch corner area. Test materials chosen for experiments are STS304-Al050-STS304, STS304-A1050-STS430-, STS304 and Al050 metals and teflon film as a lubricant is used on both sides of a workpiece. The limit drawing ration as well as quality of drawn cups (distribution of thickness and hardness)are investigated and discussed.

• 한국조리학회지
• /
• 제4권
• /
• pp.5-24
• /
• 1998

Determination of the space requirements for a restaurant is a difficult task. Because the space required is dependent upon many factors which are not constant for all types of restaurants. Today, the guides and procedures that be given are to be regarded as tentative and subject to easy change. This study tired to present the efficient methods and procedures of the space planning of restaurant. Thus, this study is on the purpose of nexts. First, finding the variables involved in the development of the model. Second, describing the approach method of modeling the facility. Third, depicting the methods and procedures of estimating the sizing of serving facilities. Fourth, developing the alternatives of sizing the space required for the facility. As illustrated, this study used the results of the model estimates and emphasized the importance of accurately evaluating the following factors. First, total number of persons to be fe. Second, meal period. Third, number of persons I the dining room. Fourth, number of persons in the serving area. Fifth, vacancy ratio.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1231-1234
• /
• 2003

A sample procedure has been described to room temperature synthesis, mesoporous aluminosilicate materials with strong surface acidity by using a cationic surfactnat cetyltrimethylammonium bromide(CTABr) as the template agent. All samples were charecterized by X-ray diffraction(XRD) and nitrogen adsorption. The crystallinity and surface area of MCM-41 type aluminosilicats decrease with decreasing of Si/Al ratio. The influence of the aluminum contents of MCM-41 on the coordination of Al and on the acidity is studied by $^{27}Al$ MAS NMR and temperature programmed desorption of ammonia(TPD). It was shown that the incorporation of Al atoms into the framework causes increasing of acid site surface. And then Al atoms in the framework were incorporated tetrahedrally in structure, which gave a rise to cationic sites in the framework.

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.87-93
• /
• 2000

Warm, forming technique which is one of the new forming technologies to improve formability of sheet metal is applied to the cylindrical cup drawing of stainless-aluminum. clad sheets. In experiments the temperature of die and blank holder is varied from room temperature to 18$0^{\circ}C$, while the punch is cooled by circulation of coolant to increase the fracture strength of workpiece on the punch corner area. Test materials chosen for experiments are STS304-A1050-STS304, STS304-A1050-STS430 clad sheets and A1050-0 aluminum sheet. Teflon film as a lubricant is used on both sides of a workpiece. The limit drawing ratio as well as quality of drawn cups(distribution of thickness and hardness)are investigated and validity of warm drawing process is also discussed.

• 한국식생활문화학회지
• /
• 제17권4호
• /
• pp.424-434
• /
• 2002

Food habit, eating-out pattern, smoking and drinking habits of 814 elderly (aged over 60) living in Incheon were surveyed by questionnaire. The ratio of the elderly who have balanced meals at moderate amount was slightly higher in urban area. Urban elderly tended to have mild foods, while rural elderly preferred hot and salty foods. Score for food habit was higher in urban elderly and there was no difference between male and female elderly. Most urban elderly had their meal at the public facilities for elderly, while most rural elderly used general restaurant and public room for elderly. Korean foods were the most favorite menu when ate out. Ratio of elderly who have difficulties in chewing was 21.2 and 39.6% for urban and rural elderly, respectively. Many elderly, especially more than 70% of female elderly, prepared the meals for themselves. Rural elderly smoked and drank more than urban elderly and male elderly did more than female elderly.