• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.8
• /
• pp.723-728
• /
• 2015

In the conventional hot rolling process, the defects of products such as scratches occur due to impact and friction. Impact occurs as a result of the contact of between rollers and the slab. Also, friction occurs in the rolling process. To improve these defects, a variety of processes were developed. The flying touch method is also one of the processes to reduce defects and uses a movable upper roller. To use this unfixed roller, the impact and frictions between rollers and the slab should be minimized. This paper proposes a hot rolling process simulator to verify and test the efficiency of the flying touch method. The simulator was designed to verify the method. This paper also proposes a new impact reducing method and velocity synchronization method which are simulated to realize the method.

• Tribology and Lubricants
• /
• v.10 no.2
• /
• pp.51-55
• /
• 1994

Rolling friction test was carried out to investigate the effect of the wear amount on rolling contact fatigue process in lubrication oil. The methods of this process were conducted at two Hertzian contact pressure and three slide ratio in each case by employing normalized and annealed carbon steel. During process of the rolling contact fatigue, the number of rotation until surface damage was occurred, the wear amount of rolling contact surface, and residual stress and half-value breadth using X-ray reflection on rolling contact surface were investigated. The result of this study shows that rolling contact fatigue process was directly influenced by wear trend and was confirmed by change of residual stress and half-value breadth on rolling contact surface.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.222-225
• /
• 2006

The effect of lubrication on the development of textures and Microstructure was studied by different lubricating condition during hot rolling of AA1050 aluminum alloy. Hot rolling without lubrication led to the evolution of the pronounced through-thickness texture gradients, whereas hot rolling with lubrication gave rise to the formation of uniform rolling texture in the whole thickness layer. The variation of texture and microstructure according to hot rolling condition are investigated by X-ray diffractometer (XRD) and Electron Back-Scattered Diffraction (EBSD). The experimental results were discussed base on the finite element method (FEM) simulation. FEM calculation reveals that a larger friction between roll and sheet causes the deviated strain state from a plane strain leading to the formation of shear textures in the thickness layers close to the surface.

• Tribology and Lubricants
• /
• v.10 no.3
• /
• pp.71-77
• /
• 1994

Rolling friction test was carried out to investigate the effect of the wear amount on rolling contact fatigue process in lubrication oil. The methods of this process were conducted at two Hertzian contact pressure and three slide ratio in each case by employing normalized and annealed carbon steel. During process of the rolling contact fatigue, the number of rotation until surface damage was occurred, the wear amount of rolling contact surface, and residual stress and half-value breadth using X-ray reflection on rolling contact surface were investigated. The result of this study shows that rolling contact fatigue process was directly influenced by wear trend and was confirmed by change of residual stress and half-value breadth on rolling contact surface.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.349-355
• /
• 1999

The texture inhomogeniety during rolling is one of the greatest problems. Especially, shear texture develops more easily during ferritic rolling of steel sheets at high temperatures due to friction between rolls and the material. In this study, the influence of front and back tensions on the texture development during ferritic rolling has been studied. The rolling textures were simulated using the full constrains Taylor-Bishiop-Hill model with the strain history obtained from finite element analysis. The calculated textures showed that the back tension rolling could reduce the shear component more effectively than front tension or rolling without tension. However, the experimental results showed that the lension effect was very small compared to our prediction. It might be attributed to initial texture and difference in frictions between simulation and experiments.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.7
• /
• pp.1149-1155
• /
• 1997

J-integral for a subsurface horizontal crack in a circular plate with an inner hole under rolling line contact is evaluated according to loading positions with various load conditions, crack length and crack location. Two-dimensional crack is modeled, and the relation between Tresca stress for uncracked model and J-integral is discussed. The loading location which gives the maximum J-integral depends on load condition and crack location, and the presence of friction force increases Tresca stress and J-integral near the surface. Regardless of friction force, crack location that gives maximum J-integral is the same as that of maximum Tresca stress in an uncracked model, and the value of J-integral is propotional to crack length. It is also showed that the variation of an inner radius of a disk does not effect J-integral value.

• Transactions of the Society of Information Storage Systems
• /
• v.9 no.2
• /
• pp.36-41
• /
• 2013

Frictional behavior of a single carbon nanotube(CNT) was investigated using molecular dynamics simulation. A single CNT aligned horizontally on silver or graphene substrate was modeled to evaluate its frictional behavior such as frictional force and rolling/sliding motion with respect to potential parameter and lattice structure of the substrate. As a result, it was found that friction and rolling was affected by adhesion between two surfaces and period of the rolling depended on lattice distance of the substrate.

• Journal of Mechanical Science and Technology
• /
• v.20 no.9
• /
• pp.1399-1409
• /
• 2006

An improved friction model was proposed with consideration of the effect of the sliding speed, the contact pressure and the temperature, and it was implemented into a user subroutine of a commercial FEM code, ABAQUS/Explicit. Then, a smooth tire was simulated for free rolling, driving, braking and cornering situations using the improved friction model and the Coulomb friction model, and the effect of the friction models on the slip, the frictional energy distribution and the cornering force and moment was analyzed. For the free rolling, the driving and the braking situations, the improved friction model and the Coulomb friction model resulted in similar profiles of the slip and the frictional energy distributions although the magnitudes were different. The slips obtained from the simulations were in a good correlation with experimental data. For the cornering situation, the Coulomb friction model with the coefficient of friction of 1 or 2 resulted in lower or higher cornering forces and moments than experimental data. In addition, in contrast to experimental data it did not result in a maximum cornering force and a decrease of the cornering moment for the increase of the speed. However, the improved friction model resulted in similar cornering forces and moments to experimental data, and it resulted in a maximum cornering force and a decrease of the cornering moment for the increase of the speed, showing a good correlation with experimental data.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1597-1603
• /
• 1995

A prediction model on forward slip has been developed for presetting rolling speed of each finish mill stand in the continuous hot strip roduction. Those factors such as neutral point, friction coefficient, volume fractions undergoing width spread, shape of deformation zone at each side of entry and delivery of the rolls were taken into account. To reduce the speed unbalance between adjacent stands a refining method of adjusting friction coefficient has also been developed. On-line application of the model showed a good agreement in rolling speeds between the predictions and the actual measurements, and gave an outstanding improvement in the travelling stability of strip passing through the finishing mill train.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.483-488
• /
• 2004

The inter-laboratory comparison test which is demanded on the authorized test of ISO/IEC 17025 is the program to guarantee the confidence of test result. This paper, as a part of the inter-laboratory comparison test between South Korea and China, is refered to the characteristic of friction coefficient of disk brake lining for rolling stock according to disk type. Brake tests were carried out under constant brake force and operating sequence by using dynamo-tester according to disk and disk lining types. To establishing the confidence of test result, we calculated A type uncertainty about friction coefficient and investigated the factors about the variation of friction coefficient.