• 한국조경학회지
• /
• 제29권4호
• /
• pp.91-99
• /
• 2001

This study was carried out to investigate the effects of mowing height, rolling, N-fertilizing, and season on green speed(i.e., ball-roll distance) for developing and implementing a program of increasing green speed in Korean golf courses. Data were subjected to multi-regression analysis using SPSSWIN(Statistical Package for the Social Science), which collected from Yong-Pyong golf course greens selected to investigate. The results was as follows. 1) The multi-regression analysis of mowing height, rolling times, and N-fertilizer application rates on spring green speed was as follows; $Y_1$(spring green speed)=4.287+0.155X$_1$(rolling times)-0.131X$_2$(the amount of N-fertilizing)-0.251X$_3$(mowing height). 2) The multi-regression analysis of mowing height, rolling times, and N-fertilizer application rates on summer green speed was as follows; $Y_2$(summer green speed)=4.833-0.423X$_3$(mowing height)+0.146X$_1$(rolling times)-0.107X$_2$(the amount of N-fertilizing). 3) The multi-regression analysis of mowing height, rolling times, and N-fertilizer application rates on fall green speed was as follows; $Y_3$(fall green speed)=4.651-0.383X$_3$(mowing height)+0.142X$_1$(rolling times)-0.103X$_2$(the amount of N-fertilizing). 4) As mowing height was lowered by 1mm, green speed increased by 0.251~0.423m. As rolling times increased by 1(one), green speed increased by0.142~0.15m. As the amount of N-fertilizing increased by 1g/$m^2$, green speed decreased by 0.103~0.131m. The season also affected green speed. In comparison with spring green speed, summer green speed decreased by 0.145m and fall green speed decreased by 0.144m.

• 소성∙가공
• /
• 제28권6호
• /
• pp.354-360
• /
• 2019

The plastic strain ratio is one of the factors that affect the deep drawability of metal sheets. The plastic strain ratio of fully annealed Cu sheet is low because its texture has {001}<100>. In order to improve the deep drawability of Cu sheet, it is necessary to increase the plastic strain ratio of Cu sheet. This study investigate the increase of plastic strain ratio of a Cu sheet after the first asymmetry rolling and annealing, and the second asymmetry rolling and annealing in air and Ar gas conditions. The average plastic strain ratio (R_m) was 0.951 and |ΔR| value was 1.27 in the initial Cu sheet. After the second 30.1% asymmetric rolling and annealing of Cu sheet at 1000℃ in air condition, the average plastic strain ratio (R_m) was 1.03 times higher. However, |ΔR| was 0.12 times lower than that of the initial specimen. After the second 18.8% asymmetric rolling and annealing of Cu sheet at 630℃ in Ar gas condition, the average plastic strain ratio (R_m) was 1.68 times higher and |ΔR| was 0.82 times lower than that of the initial specimen. These results are attributed to the change of the texture of Cu sheet due to the different annealing conditions.

• 소성∙가공
• /
• 제18권5호
• /
• pp.410-415
• /
• 2009

Experimental and numerical studies were performed to examine the effect of material temperature and reduction ratio on friction coefficient during hot flat rolling. We carried out a single pass pilot hot flat rolling test at the temperatures range of $900{\sim}1200^{\circ}C$ and measured the spread of deformed material while reduction ratio varied from 20% to 40%. Materials used in this study were a high carbon steel and two alloy steels. The dimension of specimen used in hot rolling experiment was $50mm{\times}50mm{\times}300mm$. We performed a series of finite element simulation of the hot rolling process to compute the friction coefficient change in terms of steel grade and reduction ratio. Results showed that temperature dependency of friction coefficient is not noteworthy but the effect of reduction ratio on friction coefficient is quite large. For high carbon steel, friction coefficient at reduction ratio of 30% is lower than that at that of 20%. Meanwhile friction coefficient at reduction ratio of 40% was one and half times large compared with that at that of 20%. The effect of steel grade on friction coefficient was significant when reduction ration was large, e.g., 40%.

• 소성∙가공
• /
• 제21권3호
• /
• pp.179-185
• /
• 2012

In this paper, it is proposed to produce high precision screws with a diameter of $800{\mu}m$ and a thread pitch of $200{\mu}m$ ($M0.8{\times}P0.2$) by means of a cold thread rolling process. In this part II of the study, the focus is on the production and reliability testing of the prototype $M0.8{\times}P0.2$ micro-screw. Designs for two flat dies were developed with the aid of the literature and previous studies. Process parameters during the cold thread rolling process were established through FE simulations. The simulation results showed that the threads of the micro-screw are completely formed through the rolling process. Prototype $M0.8{\times}P0.2$ micro-screw were fabricated with a high precision thread rolling machine. In order to verify the simulation results, the deformed shape and dimensions obtained from the experiment were compared with those from the simulations. Hardness and failure torque of the fabricated micro-screw were also measured. The values obtained indicate that the CAE based process design used in this paper is very appropriate for the thread rolling of micro-sized screws.

• Journal of the Korean Wood Science and Technology
• /
• 제49권4호
• /
• pp.336-359
• /
• 2021

본 연구는 고층 목조건축에 사용되는 대형 목재 패널인 CLT의 낮은 rolling shear strength를 개선하기 위해 hybrid CLT의 연구 개발 동향을 분석하였다. 이를 통해 CLT의 국산화를 위한 연구개발 방향에 활용 가능한 기초자료를 마련하고자 하였고, 낮은 rolling shear strength를 향상시키기 위한 방안으로 활엽수 층재 사용, 층재 배열 각도 변화, 구조용 목질복합체의 사용이 주를 이루고 있다. 활엽수 층재는 침엽수 보다 rolling shear strength와 shear modulus 모두 2배 이상의 높은 값을 나타내므로 활엽수 층재 사용 및 미이용 수종의 활용이 가능함을 확인하였다. 층재 배열 각도 변화에 따라 rolling shear stength 1.5배, shear modulus 8.3배, bending stiffness 4.1배 향상되어 층재 배열 각도를 감소시킴으로써 CLT 강도 향상을 확인하였다. 구조용 목질재료는 기존에 강도성능이 확보된 재료로 층재로 사용하였을 때 최대 MOR 1.35배, MOE 1.5배, rolling shear strength 2배 향상되었고, 층재 간의 접착강도 또한 집성재 블록전단강도 기준인 7.0 N/mm²을 확보할 수 있었다. 선행연구결과를 통해 MOE 7.0 GPa, MOR 40.0 MPa 이상의 휨 특성을 가진 구조용 목질재료를 사용하였을 때 강도성능이 향상됨을 확인하였다. 이를 통해 구조용 목질재료 층재 강도 기준으로 판단하였다. rolling shear strength 개선하기 위한 최적의 방법은 기존 규격에 의한 강도값을 가진 구조용 목질재료의 적용이 가장 유리할 것으로 판단하나, 구조용 목질재료의 섬유 배열에 따른 CLT 층재 배열 방향, 층재 간 접착 강도 등에 대한 추가적인 연구가 필요하다.

• Tribology and Lubricants
• /
• 제28권1호
• /
• pp.19-26
• /
• 2012

Rolling contact fatigue of an urban railway wheel was analysed during its rolling. A FEM analysis was performed using a 3D modelling of rail and wheel, considering the slope of the rail and nonlinear isotropic and kinematic hardening behavior of the rail and the wheel. The maximum von-Mises stress and contact pressure between the rail and wheel were 656.9 MPa and 1111.4 MPa, respectively, under axial load of 85 kN with friction coefficient of 0. The fatigue initiation life prediction relationships by strain-lifetime (${\varepsilon}$-N) and Smith-Watson-Topper method were drawn for the wheel steel as follows: $N_i=7.35{\times}10^6{\times}SWT^{-3.56}$ and $N_i=5.41{\times}10^{-9}{\times}(\frac{{\Delta}{\varepsilon}}{2})^{-5.77}$. The fatigue lifetimes of the wheel due to rolling contact were determined to be infinite by ${\varepsilon}$-N and SWT methods.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.1627-1633
• /
• 2004

Safety and punctuality in the subway are considered as critical factors. This system is composed of many factors like signals, rails, electrical power sources, rolling stocks. The effective inspection should be carried out at all the times for the safety and punctuality. Purpose of the rolling stocks maintenance is to offer the optimum condition of vehicles, and minimize the maintenance expenses. This paper suggests appropriate maintenance period of rolling stocks to enhance the utility efficiency in SMSC.

• Tribology and Lubricants
• /
• 제16권6호
• /
• pp.477-483
• /
• 2000

Rolling contact fatigue (RCF) tests were performed for two kinds of commercial silicon nitride balls using 4-Ball rolling contact fatigue life tester under EHL condition (Λ=8.9) and boundary lubrication condition (Λ=0.2). All the test balls were finished up to the dimensional accuracy of Grade 5 defined in KS B 2001 (Steel Balls for Ball Bearings) with a size of 8.731 mm. RCF tests were then conducted under the initial theoretical maximum contact stress 6.63 GPa and the spindle speed 10,000 rpm. All the test balls were not failed until 3.75 $\times$ 107 contact cycles and wear tracks of test balls were not conspicuous under EHL condition (Λ= 8.9). In the operations of low lambda regime (Λ= 0.2), all the test balls were surface damaged and high rolling wear resistance was achievable in fully densified using MgO 1 wt% and HIPed balls. Rolling wear of silicon nitride balls under boundary lubrication condition depend mainly on grain size and intergranular phase content of silicon nitride balls.

• 소성∙가공
• /
• 제29권2호
• /
• pp.69-75
• /
• 2020

The plastic strain ratio is one of the factors that affect the deep drawability of metal sheets. The plastic strain ratio of fully annealed Cu sheet is low, due to its texture being {001}<100>. In this study, in order to increase the plastic strain ratio of Cu sheets we investigated the effect of two treatments: 1^st the sheet was asymmetrically rolled and annealed, and 2^nd the sheet was symmetrically and asymmetrically rolled and subsequently annealed. The average plastic strain ratio (R_m) of the initial Cu sheet was 0.95 and |Δr| was 1.27. After the 2^nd treatment of 5.3% symmetric rolling and annealing of Cu sheet at 1000℃ for 60 min in Ar gas condition, the R_m was 2.29 times higher and the |Δr| was 1.44 times higher than that of initial Cu sheet specimen. After the 2^nd treatment of 8.2% asymmetric rolling and annealing of Cu sheet at 1000℃ for 60 min in Ar gas conditions, the R_m was 2.51 times higher and |Δr| was 0.53 times lower than that of the initial Cu sheet specimen. These results can be attributed to the change in texture of the Cu sheets due to the differences in the two methods of rolling.

• 한국재료학회지
• /
• 제4권4호
• /
• pp.406-415
• /
• 1994

분말충진법에 의한 Ag/Bi-2223고온초전도선재의 제조방법 및 제조조건에 따른 임계전류밀도를 조사하였다. 전체공정에서 250시간의 열처리 및 2회의 반봅가공 조건에서 임계전류밀도가 가장 높게 측정되었다. 이와 같은 결과는 250시간의 열처리에서 고온상이 크게 성장되었으며, 2회의 반복가공으로 결정입자들이 일방향으로 잘 배열되는 공정조건임을 알 수 있었다. 공정별로는 pressing방법으로 제조한 시편의 임계전류밀도가 $1.05\times 10^4A/\textrm{cm}^2$로 다른 공정에 비해 가장 높았으며, rolling 공정으로는 $0.78\times 10^4A/\textrm{cm}^2$를 갖는 선재를 제조하였다. 7개 및 49개의 세심을 갖는 다심선재를 제조하여 임계전류밀도를 조사하였다. 7개의 다심선재에서 임계전류밀도값은 pressing방법에서 $0.45 \times 10^{4}A/\textrm{cm}^2$ 였으며, 49개 다심은 rolling방법으로 $0.20 \times 10^{4}A/\textrm{cm}^2$를 갖는 선재를 제조하였다.