• International Journal of Precision Engineering and Manufacturing
• /
• 제3권1호
• /
• pp.26-32
• /
• 2002

Laser direct patterning of the coated photoresist (PMER-NSG31B) layer was studied to make halftone dots on the gravure printing roll. The selective laser hardening of the photoresist by Ar-ion laser(wavelength: 333.6∼363.8 nm) was controlled by the A/O modulator. The coating thickness in the range of 5∼11㎛ could be obtained by using the up-down directional moving device along the vertically located roll. The width, thickness and hardness of the hardened lines farmed under the laser power of 200∼260mW and irradiation time of 4.4∼6.6 $\mu$ sec/point were investigated after developing. The hardened width increased as the coating thickness increased. Though the hardened thickness was changed due to the effect of the developing solution, the hardened layer showed good resistance to the scratching of 2H pencil. Also, the hardened minimum line width of 10㎛ could be obtained. The change of line width was also found after etching, and the minimum line widths of 6㎛ could be obtained. The hardened lines showed the good resistance to the etching solution. Finally, the experimental data could be applied to make gravure halftone dots using the developed imaging process, successfully.

• 한국재료학회지
• /
• 제17권7호
• /
• pp.361-365
• /
• 2007

A deoxidized low-phosphorous copper processed by eight cycles of accumulative roll-bonding (ARB) was annealed at various temperatures ranging from 100 to $400^{\circ}C$. The annealed copper was characterized by transmission electron microscopy (TEM) and tensile & hardness test. TEM observation revealed that the ultrafine grains developed by the ARB still remained up to $350^{\circ}C$, however above $400^{\circ}C$ they were replaced by equiaxed and coarse grains due to an occurrence of the static recrystallization. The hardness of the copper decreased slightly with the annealing temperature up to $350^{\circ}C$, however they dropped largely above $400^{\circ}C$. Annealing characteristics of the copper were compared with those of an oxygen free copper processed by ARB and subsequently annealed.

• 해양환경안전학회지
• /
• 제29권4호
• /
• pp.380-388
• /
• 2023

본 연구는 모형선박의 횡방향 무게분포를 변화시키면서 횡요주기 및 관성모멘트에 의한 GM을 추정하고 경사시험으로 계측되는 GM 값과 비교한다. 그 과정에서 각 수치를 분석하여 관계성을 파악한다. 실험 및 비교에 사용된 선박의 종류는 3종류로 7톤급, 20톤급 어선과 KVLCC의 모형선을 사용하였다. 실험은 스윙프레임 테스트와 자유 횡요 감쇠테스트를 수행하여 관성모멘트와 횡요주기를 계측하고, 경사시험으로 GM을 계측하였다. 관성모멘트와 횡요주기로 추정된 GM과 경사시험으로 구해진 GM은 선박의 무게 분포 변화에도 동일한 경향을 보였지만, 경사시험에서 구해진 GM이 더 작은 값을 보였다. 따라서 GM 추정 시에 관성모멘트나 횡요주기 외에도 추가적인 보정 계수나 파라미터가 필요하다고 판단된다. 추후 무게중심을 변화시켜 추정 GM과의 관계를 분석하여 보정 계수를 산출할 계획이다.

• 한국자동차공학회논문집
• /
• 제8권4호
• /
• pp.121-129
• /
• 2000

this paper develops a computational model for the turning maneuver analysis of a cabover type heavy truck. The model having 42 degree-of-freedom is developed using ADAMS. Leaf springs used in the front and rear suspension systems are modeled by dividing it three links and joining them with joints. Force and displacement relationship showing nonlinear hysteric characteristics of the leaf spring is measured and modeled with an exponential function. A velocity and force relationship of a shock absorber is measured and modeled with a spline function. And a stabilizer bar is modeled using ADAMS beam element to consider a twisting and bending effect. To verify the developed model an actual vehicle test is performed in the double lane change course with 50kph and 60kph vehicle velocity. In the actual vehicle test lateral acceleration roll angle and yaw rate are measured, The tendency and peak-to-peak values of the actual vehicle test and simultion results are compared each other.

• 소성∙가공
• /
• 제8권1호
• /
• pp.78-91
• /
• 1999

The endless hot rolling has been focused as an innovative process technology for increasing the productivity drastically and reducing the imperfection of quality in hot rolled steel strip. To realize it in actual mill, a lots of new facilities such as bar coiler, movable LASER welder and high speed strip shear should be equipped. And also it is necessary to develop the control technique for changing the roll gap and rolling speed during rolling, which is named as Flying Gap and Speed Change control technology. To prevent a strip rupture caused by excessive tension, it is very important to minimize fluctuations in strip thickness and intension during FGSC control. In this paper, the mathematical model for FGSC control algorithm was suggested and dynamic simulation is performed to accertain the effect of suggested control method on fluctuations in strip thickness and tension. For endless hot rolling simulation, a lots of FGSC control situations, for instance - strip thickness change from strip to strip - strip width change from strip to strip - carbon content change from strip to strip are considered.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.1.2-1.2
• /
• 2011

With recent advances in materials and products, materials processing experiences new challenges. More particles and polymers in material side and thinner and faster deformations in processing side. It happens in most emergying industries such as manufacturing of batteries, solar cells, multi-layer chips, displays, printed electronics, to list a few. In most cases, they are manufactured by coating or printing process, which is defined as a process in which gas is replaced by liquid on a substrate. In this sense, casting, inkjet printing, and roll-to-roll printing are all included. The printing process consists of three unit processes. As the materials used in the above mentioned applications typically contain a large amount of particles with polymers and solvents, they continuously change microstructures during preparation, flow, and even drying. However, little is known about the flow characteristics of such complex fluids and less is known about how to design and control the process. Therefore, for better control of the process and for better quality of the product, we need to understand the flow characteristics of these complex fluids under extremely fast flow environment.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.766-771
• /
• 1997

In this strip casting,size of the roll separating force is a index representing the solidifying status of the melt. Rolling forces at the start of the casting process can change abruptly due to the overcooling of the leader strip. This inconsistensy leads to machine damage or deficient solidification which results in the failure of the casting. In this study, a mathematical model is derived for the hydraulic servo pressure control system for the twin roll strip caster and its parameters are estimated by the RLS algorithm. Based on the identified model, an one-step ahead predictive control method is applied in order to minimize the transient fluctuation of the rolling force. Its simulation results are compared with those of the conventional PI controllers.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.203-203
• /
• 2012

The SWCNTs network are formed on various plastic substrates such as poly(ethylene terephthalate) (PET), polyimide (PI) and soda lime glass using roll-to-roll printing and spray process. Selective patterning of carbon nanotubes film on transparent substrates was performed using a femtosecond laser. This process has many advantages because it is performed without chemicals and is easily applied to large-area patterning. It could also control the transparency and conductivity of CNT film by selective removal of CNTs. Furthermore, selective cutting of carbon nanotube using a femtosecond laser does not cause any phase change in the CNTs, as usually shown in focused ion beam irradiation of the CNTs. The patterned SWCNT films on transparent substrate can be used electrode layer for touch panels of flexible or flat panel display instead indium tin oxide (ITO) film.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.64-66
• /
• 2007

Asymmetric rolling, where circumferential velocities of the upper and lower rolls differ, can be one method to change texture of magnesium alloy sheet by introducing shear deformation throughout the thickness of a sheet. In this study, the texture, microstructure and mechanical properties of AZ31 Mg sheets has been investigated during the symmetrical rolling procedure and the asymmetric rolling procedures of different roll speeds with different roll diameters. Texture of Mg alloy sheets were evaluated by using X-ray diffraction and ODFs were calculated using ADC method. The major texture of rolled specimens can be expressed by ND//(0001) fiber texture. The major fiber texture changed according to the rolling processes and such a slight difference of texture changes the formability of sheets. The mechanical properties were enhanced during asymmetrical rolling.

• 동력기계공학회지
• /
• 제18권4호
• /
• pp.112-116
• /
• 2014

Roll and pitching motions of a vessel can seriously degrade the performance of mechanical systems and the effectiveness of personnel. Many studies on roll stabilization and trimming control system design have focused on stabilizing the vessel through the use of fins, tanks, rudders and flaps. However the ultimate objective of such approaches must be to improve boarding sensitivity. This paper presents an anti-seasickness bed that consists of a rotator and bearing system that does not make use of electric power. The advantages of this system are its simple construction, usefulness, and safe operation. In this study, the rotation angles of the upper plate of a bed according to change weight of the rotator have been calculated to determine the stability. As a result, it can be concluded that proposed stabilizing bed can be of practical use in the field.