• 한국가시화정보학회지
• /
• 제17권3호
• /
• pp.12-18
• /
• 2019

Direct numerical simulation of a fully developed turbulent plane Couette-Poiseuille flow with a two-dimensional (2-D) rod-roughened wall is performed to investigate the impacts of the surface roughness. It is shown that the logarithmic region in the mean velocity profile over the rough wall Couette-Poiseuille flow is significantly shortened by the surface roughness compared to that over a turbulent Couette-Poiseuille flow with smooth wall. The Reynolds shear stress over the rough wall Couette-Poiseuille flow is decreased compared to that for a smooth case in the outer layer. These results are attributed to weakened turbulence activity or roll-cell mode over the rough wall Couette-Poiseuille flow near the channel centerline due to suppressed development of u'-structure on the top wall, as documented through spanwise energy spectra of the streamwise velocity fluctuations. Inspection of congregation motion near the bottom wall and time evolution of u'-structure reveal weakened co-supporting cycle for the rough wall case.

• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.664-670
• /
• 2011

3-ply Mg/Al/STS clad-metal was fabricated by the roll bonding process. An interfacial reaction layer was formed at the Mg/Al interface at and above $300^{\circ}C$ whereas no interfacial reaction layer was observed up to $400^{\circ}C$. The effect of the interfacial reaction layer on the mechanical and fracture properties in clad metals after heat treatments were investigated The chemical compositions were analyzed at the Mg/Al interface by an Energy dispersive X-ray analysis (EDX). A tension test was performed to examine the interfacial cracking properties. The Mg layer fractured first, causing a sudden drop of the stress and Al/STS layer continued to deform until the final fracture. Periodic cracks and crack propagation was observed at the reaction layer between Mg and Al.

• 한국식품과학회지
• /
• 제36권2호
• /
• pp.276-282
• /
• 2004

쌀보리와 거의 유사한 식품학적 특성을 지니지만 활용도가 극히 낮은 보리 파쇄립을 이용하여 압출성형에 의한 보리 후레이크를 개발하였다. 압출성형시 $100^{\circ}C$ 이상의 온도, 35% 이상의 수분함량에서 파쇄립이 충분히 호화되었으며, 메성보리 파쇄립의 경우 찰성보리에 비해 절단성, roll 분리성 등이 우수하였다. 메성 및 찰성보리 파쇄립의 혼합비율을 달리하면서 압출성형하여 제조한 pellet의 특성을 조사한 결과 찰성보리 파쇄립의 혼합비율이 증가할수록 RVA 상의 최고점도가 감소하였고 또한 겉보기 점도와 항복력이 감소한 반면 유동지수는 증가하였다. 그리고 이를 oil frying하여 제조한 후레이크의 특성을 조사한 결과 찰성보리 파쇄립의 혼합비율이 증가함에 따라 압착강도와 bulk density가 크게 감소하였고 단면상에서의 air cell 크기가 커지고 cell을 이루는 body가 얇아지는 것으로 나타났다. 그리고 관능검사 결과 찰성보리 파쇄립의 혼합비율이 증가할수록 조직감과 맛에 대한 기호도가 증가하였고 메성과 찰성보리 파쇄립의 혼합비율 (60-70):(30-40) 처리구의 경우 관능적으로 가장 바람직한 것으로 나타났다.

• Journal of Nutrition and Health
• /
• 제35권2호
• /
• pp.229-236
• /
• 2002

Cataracts are the leading cause of blindness worldwide and are characterized by increased opacity of the lens that significantly diminishes visual acuity. It has been suggested that increased risk of lens opacities are associated with age, exposure to sunlight, diabetes, smoking, and poor nutrition. Antioxidant nutrients have born demonstrated to protect the lens membrane and protein against damage due to oxidative stress. The purpose of this study was to investigate the antioxidant system in the blood of cataract patients. The status of the blood antioxidant system was evaluated based on the levels of antioxidant vitamins and minerals as well as glutathione peroxidase (GSH-Px) and malondialdehyde (M7A) activity in 34 patients with cataracts (17 male and 17 female) and 45 control subjects (20 male and 25 female). After adjusting for age, the results showed significantly lower levels of antioxidant vitamins such as lycopene (M : p < 0.05, F: p < 0.01), zeaxanthin (F: p < 0.01), ${\gamma}$-tocopherol (F: p < 0.01) and ascorbic arid (M: p < 0.05) in the cataract patients than in the control subjects. In contrast, the concentration of cryptoxanthin (F : p < 0.07) showed a significantly higher value in the cataract patients. The serum level of the antioxidant mineral Zn (M : p < 0.01) was found to be significantly lower in the cataract patients while the ratio of cu/zn appeared significantly higher (M : p < 0.05). Significantly higher (M : p < 0.01, F: p < 0.05) concentrations of MDA in serum was found in the cataract patients as compared to the control subjects. GSH-Px activity was significantly lower (F: p < 0.05) in 71e cataract patients. In conclusion, the antioxidant system may play an important roll in cataract creation. Further studies are needed to clarify the mechanisms underlying these findings and to establish preventive measures with an emphasis on antioxidant nutrition for cataract patients.

• Journal of Astronomy and Space Sciences
• /
• 제27권3호
• /
• pp.253-262
• /
• 2010

The electrical power system (EPS) of Korean satellites in low-earth-orbit is designed to achieve energy balance based on a one-orbit mission scenario. This means that the battery has to be fully charged at the end of a one-orbit mission. To provide the maximum solar array (SA) power generation, the peak power tracking (PPT) method has been developed for a spacecraft power system. The PPT is operated by a software algorithm, which tracks the peak power of the SA and ensures the battery is fully charged in one orbit. The EPS should be designed to avoid the stress of electronics in order to handle the main bus power from the SA power. This paper summarizes the results of energy balance to achieve optimal power sizing and the actual trend analysis of EPS performance in orbit. It describes the results of required power for the satellite operation in the worst power conditions at the end-of-life, the methods and input data used in the energy balance, and the case study of energy balance analyses for the normal operation in orbit. Both 10:35 AM and 10:50 AM crossing times are considered, so the power performance in each case is analyzed with the satellite roll maneuver according to the payload operation concept. In addition, the data transmission to the Korea Ground Station during eclipse is investigated at the local-time-ascending-node of 11:00 AM to assess the greatest battery depth-of-discharge in normal operation.

• 한국산학기술학회논문지
• /
• 제18권5호
• /
• pp.29-34
• /
• 2017

본 논문에서는 압연 공정을 통해 리드용 와이어를 생산할 때 생산성을 향상시키기 위해 와이어의 직진 속도를 증가시키는 방법을 연구했다. 직진 속도를 증가시킬 때 가장 중요한 점은 와이어가 원래의 목적을 바르게 수행할 수 있는 것이다. 즉, 와이어의 직진 속도가 증가함과 동시에 균열이 발생하지 않으며, 치수 공차를 만족시켜야 한다. 하지만 와이어의 직진속도를 증가시키게 되면 기존의 압하량 보다 더 큰 수치를 주어야 하고 이는 와이어에 보다 큰 손상을 주어 표면에 무리를 주게 된다. 따라서 기존의 2단계 평압연 공정을 통해 생산되었던 와이어의 필요스펙을 충족시키면서 생산성 향상까지 도모할 수 있는 3단계 평압연 공정에 관해 연구하였다. 본 연구에서는 3단계 평압연 롤러의 압하량만을 변수로 가정하고 다른 조건은 현장 조건과 일치시킨다. 상용 PIDO(Process Integration and Design Optimization) 툴인 PIANO (Process Integration, Design and Optimization)를 통해 지정한 변수 3가지를 조작하면서 실험점을 분포하고 이를 바탕으로 최적설계를 진행하여 와이어의 생산성을 향상시킴과 동시에 필요 스펙인 최대 응력의 최소화가 가능하도록 설계되었다.

• 농업과학연구
• /
• 제42권4호
• /
• pp.325-333
• /
• 2015

The ventilation systems composed three types of side vent (roll-up) 'SV', side vent+roof vent 'SV+RV', and side vent+roof fan 'SV+RF' with 7.5 m spacing, with specific set point temperatures for ventilation: SV ($35^{\circ}C$ open / $33^{\circ}C$ close), SV+RV or SV+RH ($35^{\circ}C$ open/$33^{\circ}C$ close for root ventilation and $37^{\circ}C$ open / $35^{\circ}C$ close for side vent). In the treatment of SV+RV, although the average daily maximum temperature inside the greenhouse temporarily increased by $38-40^{\circ}C$, thermal stress by high temperature did not occur and the disease incidence (%) of powdery mildew and downy mildew on the oriental melon were 25 - 75% lower than in the conventional SV treatment. In the SV treatment, the disease incidence (%) of powdery mildew and downy mildew were 1.4 - 7.7% and 4.2 - 15.9% for 'Deabakkul', and 20.3 - 22.8% and 2.8 - 11.3%, for 'Ildeungkkul'. The yield for one month was higher in the treatment of SV+RV than those in other treatments, with values of 2,105 kg/10a for 'Deabakkul' and 2,537 kg/10a for 'Ildeungkkul'. The simultaneous treatment with side vent and roof vent resulted in 16.2% higher yield (18.1% higher marketable yield) than that in the SV treatment for 'Deabakkul'.

• 한국전문물리치료학회지
• /
• 제9권3호
• /
• pp.113-124
• /
• 2002

The objectives of this study was to investiage the effects of sitting posture on carpal tunnel syndrome. Carpal tunnel syndrome (CTS) continues to be one of the most widely publicized maladies of the cumulative trauma disorder. Many studies have reported a positive association between CTS and highly repetitive work, high force, and poor posture. High force and repetitive work have especially been associated with CTS, but the evidence for work being a primary cause of CTS is strongest when these factors are combined. In addition to carpal tunnel syndrome, hand, wrist, and other disorders are attributed to these work-related movements. Such disorders are referred to as repetitive stress injuries, cumulative trauma disorder, overuse syndromes, and chronic upper limb pain syndrome. Incorrect posture also may play a role in the development of CTS in people who work at a computer and other types of keyboards. The tendency to roll the shoulders forward, round the lower back, and thrust the chin forward can shorten the neck and shoulder muscles, compressing nerves in the neck. This, in turn, can affect the wrist, fingers, and hand. The treatment and prevention of carpal tunnel syndrome continue to be approached with a segmental view of the human body. For example, the most common ergonomic solution for carpal tunnel syndrome associated with keyboard use is to keep the wrists in a neutral position by using a wrist rest in front of the keyboard and good sitting posture.

• 대한기계학회논문집A
• /
• 제36권12호
• /
• pp.1619-1625
• /
• 2012

전기강판은 모든 형태의 변압기나 모터의 코어 소재로 사용되고 냉간압연 공정에 의해 생산된다. 본 논문에서는 냉간압연 중에 발생하는 전기강판 에지에서의 파단을 예측할 수 있는 손상역학에 기초한 접근법을 제시할 것이다. 손상개시 판단조건으로 수직 인장응력 조건을 도입하였고 손상진전 기법으로 손상 에너지법을 채용하였다. 전기강판 에지의 초기 노치로부터 크랙 발생과 전파 모사를 위해 유한요소법을 이용하였다. 유한요소해석에서 요구되는 물성치는 일반적인 판형 시편과 노치가 있는 판형 시편을 이용하여 인장 테스트를 통해서 확보하였다. 에지 크랙은 롤 바이트의 입측에서 시작되고 롤 바이트 출측에서 급격하게 진전되는 것으로 나타났다. 초기 노치의 길이와 강판의 전방 텐션릴 하중이 커짐에 따라 에지 크랙의 성장길이는 커지는 것으로 나타났다.

• 대한금속재료학회지
• /
• 제50권5호
• /
• pp.345-351
• /
• 2012

A three-point bending test was performed on roll-bonded Mg/Al/STS clad-metal plates under two different testing conditions (Mg layer in tension, or STS in tension) and their mechanical response and fracture behavior were investigated. Bending strength was found to be greater under the condition of Mg layer in tension. Heat treatment at $200^{\circ}C$ increased the bending formability, suggesting the interfacial strength increased at $200^{\circ}C$. Under the condition of Mg in tension, the clad heat-treated at $300^{\circ}C$ and $400^{\circ}C$ fractured in two steps, with the first step associated with the interfacial fracture between Mg and Al, and the second the fracture of the Mg layer. STS/Al layers were found to be bent without complete fracture. Under the condition of STS in tension, the clad heat-treated at $300^{\circ}C$ and $400^{\circ}C$ exhibited a very small load drop at the displacement, which is similar to that of the first load drop associated with the interfacial fracture under the condition of Mg in tension. In this case, no interfacial cracks were found and the complete cut-through fracture of clad was observed at low temperature heat treatment conditions, suggesting excellent interfacial strength. When the heat treatment temperature was higher than $300^{\circ}C$, interfacial cracks were observed. The local stress condition and the position of the interface with respect to the surface were found to have a great influence on the fracture behaviors of clad metals.