• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.286-287
• /
• 2008

The determination of roll speeds in continuous rolling system is an important factor along with the design of roll profile and roll gap. The tensile force on the workpiece induces reduced cross section area and the compressive force induces wrinkles. To determine the optimal roll speeds of current rough rolling system for wire rod, FE analysis was performed. We could predict the workpiece shape and the stress level more precisely by considering the elasto-plastic behavior of workpiece. Also the efficient analysis methodology is presented to reduce the calculation time by combining the ALE and lagrangian method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.242-251
• /
• 1999

The temperature distribution over the work roll length was estimated by solving a 2-dimensional heat transfer equation based on the rolling conditions and the thermal boundary conditions. In order to solve the governing equation, a finite volume method was employed. In the rolling conditions, the strip temperature, the contact time between roll and strip, the roll speed, the strip thickness, the rolling force and the rolling and idling time were used as input data. In order to verify the accuracy of temperature estimation, roll surface temperatures were measured in the roll shop. The measured temperatures showed a good correlation with the calculated ones.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.37-46
• /
• 1999

Sheet pil VL 제조에 있어서 핵심적인 중요 기술은 압연 중 진행 소재가 좌우 휨이 없이 직진토록하여 치입 상에 문제가 없어야 하는 것이며, 또 하나는 압연 완료후 냉각 중에 있는 제품의 bending량을 최소로 하여 roller 교정기에서 1차 교정으로 교정이 완료되게 하는 것이다. 압연중 소재가 직진토록 하기 위해서 web와 flange 등의 caliber 협상에서 balance가 유지되어야 하므로, web와 flange의 reduction을 1:1 vs 1.0으로 web의 압하가 flange에 비해 10%정도 크게 하였고, 좌우 flange의 reduction이 변화하지 않도록 flange 온도 보존을 위하여 intermediated에서 2 pass를 생략하여 약 40초의 rolling time을 단축시켰고, 이는 7$0^{\circ}C$정도의 온도 drop를 방지하는 효과를 나타내었다. 이로 인한 roll force는 약 15%정도 down 되었다. 논리상으로 A3 변태점 이하에서 web(두꺼운 부분 24.3mm)나 flange(얇은부분 9.5mm)가 동시에 압연이 완료된다면 bending량은 휠씬 줄어든 것이나, 이 경우 roll force 증가에 따른 roll 절손 사고의 위험과 설비 trouble이 우려되기 때문에 web 온도를 약 95$0^{\circ}C$에서 flange 온도를 83.$0^{\circ}C$에서 압연 완료토록 함으로써 설비 안전을 도모하였고, 1차 교정을 위하여 냉각 주수 설비를 설치하여 공냉시켰을 때의 1400mm에서 700mm로 bending량을 감소시킴으로써 이를 가능토록하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.8
• /
• pp.855-861
• /
• 2011

We predict the rolled-strip profile for a 6-high mill using thin rolling theory and a numerical model. In the numerical model, we calculate the distributions of the contact pressures between the rolls and the rolling pressure between the strip and the work roll in the transverse direction using the geometric structure of the 6-high mill and the boundary conditions. We determine the distribution of the rolling pressure in the rolling direction via a thin-foil rolling model using Fleck's theory. We calculate the three-dimensional elastic deformation of the work roll using the pressures of the width and rolling directions. We then obtain the three-dimensional strip profile via the elastic deformation of the work roll during the rolling process. The profile is verified by a thin cold-rolling test and FE simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.871-875
• /
• 1996

The Output feedback linear quadratic regulator control is applied to the design of active suspension system using 7 DOF full car model. The performance index reflects the vehicle vertical movement, pitch and roll motion, and minimization of suspension stroke displacements in the rattle space. The elements of gain matrix are approximately decoupled so that each suspension requires only local information to generate the control force. The simulation results indicates that the output feedback LQ controller is more effective than purely passive or full state feedback active LQ controllers in following the road profile at the low frequency range and suppressing the road disturbance at the high frequency ranges.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.175.2-175
• /
• 2001

The strip profile and shape control is one of the most important technologies in Hot Rolling Mill System. Because the unbalance of strip´s shape and wave appearance between stands has a bad effect on Hot Rolling Mill System by making the inferior thickness, strip´s damage and so forth in factories. Many competition Plate Mill introduced shape control system, for example, pair cross-mill, work roll bender, which includes shape measuring instruments and shape control mathematical models. Shape meter, which is equipped for flatness, only does feedback control at the top of coil. And, for crown, we depend on initial setup value and there is no feedback control. Therefore we predict the shape of strip using rolling pressure, bender force and tension of inter-stand in ...

• Transactions of Materials Processing
• /
• v.25 no.2
• /
• pp.130-135
• /
• 2016

Rolled products often have residual stresses or strip waves that are beyond the customer’s tolerance. To resolve this problem, skin-pass rolling is widely used during post-processing of such products. Because a short contact length compared to the strip width is a characteristic of skin-pass rolling, several numerical analyses have been previously conducted based on a two-dimensional approach. In the current study, a series of simulations was conducted using numerical analysis of three-dimensional elastic-plastic finite element method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.12
• /
• pp.1005-1011
• /
• 2016

The fundamental reason for gear noise is transmission error. Transmission error occurs because of STE (static transmission error) and DTE (dynamic transmission error), while a pair of gears is meshing. These errors are generated by the deflection of the teeth and the friction on the surface of the teeth. In addition, the vibration generated by transmission error leads to excited bearings. The bearings support the shafts, and the noise is radiated after exciting the gear casing. The analysis of the contact stress in helical gear tooth flanks indicates that it is due to impact loading, such as the sudden engagement and disengagement of a gear. Stress analysis is performed for different roll positions, in order to determine the most critical roll angle. Dynamic analysis is performed on this critical roll position, in order to evaluate variation in stresses and tooth contact force, with respect to time. In this study, transmission error analysis was implemented on a spur and helical gear with involute geometry and a modified geometry profile. In addition, in order to evaluate the intensity of impact due to sudden engagement and significant backlash, the impact factor was calculated using the finite element analysis results of static and dynamic maximum bending stresses.

• Korea-Australia Rheology Journal
• /
• v.12 no.2
• /
• pp.107-117
• /
• 2000

Prediction of the product shape in sheet casting process is performed from the numerical simulation. A three-dimensional finite element method is used to investigate the flow behavior and to examine the effects of processing conditions on the sheet produced. Effects of inertia, gravity, surface tension and non-Newtonian viscosity on the thickness profile of the sheet are considered since the edge bead and the flow patterns in the chill roll region have great influence on the quality of the products. In the numerical simulation with free surface flows, the spine method is adopted to update the free surface, and the force-free boundary condition is imposed along the take-up plane to avoid severe singularity problems existing at the take-up plane. From the numerical results of steady isothermal flows of a generalized Newtonian fluid, it is shown that the draw ratio plays a major role in predicting the shape of the final sheet produced and the surface tension has considerable effect on the bead thickness ratio and the bead width fraction, while shear-thinning and/or tension-thickening viscosity affect the degree of neck-in.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.683-690
• /
• 2012

In this work, the semi-active control of a large-sized bus suspension system with an MR damper was studied. An MR damper model that can aptly describe the hysteretic characteristics of an MR damper was adopted. Parameter values of the MR damper model were suitably modified by considering the maximum damping force of a passive damper used in the suspension system of a real large-sized bus. In addition, a fuzzy logic controller was developed for semi-active control of a suspension system with an MR damper. The vertical acceleration at the attachment point of the MR damper and the relative velocity between sprung and unsprung masses were used as input variables, while voltage was used as the output variable. Straight-ahead driving simulations were performed on a road with a random road profile and on a flat road with a bump. In straight-ahead driving simulations, the vertical acceleration and pitch angle were measured to compare the riding performance of a suspension system with a passive damper with that of a suspension with an MR damper. In addition, a single lane change simulation was performed. In the simulation, the lateral acceleration and roll angle were measured in order to compare the handling performance of a suspension system using a passive damper with that of a suspension system using an MR damper.