• 열처리공학회지
• /
• 제10권4호
• /
• pp.246-254
• /
• 1997

The 6.5wt %Si-Fe alloy sheets were made by the twin roll process. The magnetic properties and microstructures of sheets annealed in the sulfur atmosphere were studied. In the as-prepared sheet, non-oriented columnar grains about $10{\mu}m$ in diameter were observed, which grew from the surface to the inner part of the sheet. When the annealing temperature was around $700^{\circ}C$, the primary recrystallization was formed around the middle part of the sheet thickness, and the grain size increased with increasing annealing temperature. At the annealing temperature of $900^{\circ}C$, the grain size became $30{\sim}40{\mu}m$. Around the annealing temperature, the motive force of the grain growth is the grain boundary energy. However, above $1000^{\circ}C$ the surface energy played an important role in the observed grain growth. When the sheet were annealed at $1200^{\circ}C$, the grains whose (100) planes were paralled to the thin plate surface grew, and all sheet surfaces were covered with these grains after 1 hour annealing. This phenomenon is called tertiary recrystallization. A difference in surface energy between (100) and (110) surfaces provides a driving force for growth of tertiary grains. The coercive force was 0.27 mOe and the AC core loss $W_{12/50}$ was 0.38w/kg for the 6.5wt%Si-Fe alloy.

• Nano
• /
• 제13권12호
• /
• pp.1850142.1-1850142.9
• /
• 2018

Modified titanate nanotubes (TNT) were tested for their adsorption of methylene blue (MB) from water solutions. They were obtained from the $TiO_2$ nanopowder using a standard alkaline hydrothermal method but in the stage of acid washing, when the titanate flakes begin to roll into nanotubes, magnetite nanoparticles were added. The $Fe_3O_4$ magnetic nanoparticles with diameter of around 2 nm and 12 nm were used in the tests. Significantly stronger adsorption of MB was observed when smaller nanoparticles were used compared to using larger nanoparticles and compared to the case of unmodified nanotubes. It was shown that the increased adsorption of MB is associated with a more negative value of ${\zeta}$-potential for titanates modified by the ultra-small nanoparticles. In the adsorption experiment, pH 7 was selected. These results may prove to be of great importance in the case of potential applications corresponding to the use of such material for wastewater purification.

• 반도체디스플레이기술학회지
• /
• 제20권3호
• /
• pp.51-56
• /
• 2021

Using an inkjet printing process, we have investigated a droplet formation of poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) near the orifice of a piezoelectric inkjet head. With an attempt to form the smallest droplet without any satellites, we have applied various waveforms such as the unipolar, bipolar, and M-shaped waveforms. It is found that the droplet velocity and volume vary depending sensitively on the waveform width and voltage. Of those, the M-shaped waveform is shown to provide the smallest droplet volume, followed by the bipolar and then unipolar waveforms. The droplet printed on a PET film roll by the M-shaped waveform has the diameter as small as 46.1 ㎛. It is likely that the second short unipolar in the M-shape waveform increases the droplet velocity gradient, rendering the droplet smaller.

• 한국재료학회지
• /
• 제22권9호
• /
• pp.476-481
• /
• 2012

Among the various roll-to-roll printing technologies such as gravure, gravure-offset, and reverse offset printing, reverse offset printing has the advantage of fine patterning, with less than 5 ${\mu}m$ line width. However, it involves complex processes, consisting of 1) the coating process, 2) the off process, 3) the patterning process, and 4) the set process of the ink. Each process demands various ink properties, including viscosity, surface tension, stickiness, and adhesion with substrate or clich$\acute{e}$; these properties are critical factors for the printing quality of fine patterning. In this study, Ag nano ink was developed for reverse offset printing and the effect of polyvinylpyrrolidone(PVP), used as a capping agent of Ag nano particles, on the printing quality was investigated. Ag nano particles with a diameter of ~60 nm were synthesized using the conventional polyol synthesis process. Ethanol and ethylene glycol monopropyl ether(EGPE) were used together as the main solvent in order to control the drying and absorption of the solvents during the printing process. The rheological behavior, especially ink adhesion and stickiness, was controlled with washing processes that have an effect on the offset process and that played a critical role in the fine patterning. The electrical and thermal behaviors were analyzed according to the content of PVP in the Ag ink. Finally, an Ag mesh pattern with a line width of 10 ${\mu}m$ was printed using reverse offset printing; this printing showed an electrical resistivity of 36 ${\mu}{\Omega}{\cdot}cm$ after sintering at $200^{\circ}C$.

• 농업과학연구
• /
• 제40권4호
• /
• pp.317-323
• /
• 2013

This research was conducted to obtain the basic information for establishment of standard guidelines in the design and installation of roof ventilation system in single-span plastic greenhouse. To achieve this, the greenhouse structure & characteristics, cultivation status, and ventilation system were investigated for single-span greenhouse with roof ventilation system cultivating the Cucurbitaceae vegetables, watermelon, cucumber, and oriental melon. Most of single-span watermelon greenhouse in Haman and Buyeo area were a hoop-style and the ventilation system in those greenhouses mostly consisted of two different types of 'roof vent (circular or chimney type) + side vent (hole) + fan' and 'roof vent (circular type) + side vent (hole or roll-up type)'. The diameter of circular and chimney-type vent was mostly 60cm and the average number of vents was 10.5 per a bay with vent spacing of average 6.75m. The ratio of roof vent area to floor area and side vent area in the single-span watermelon greenhouse with ventilation fan were 0.46% and 7.6%, respectively. The single-span cucumber greenhouse in Haman and Changnyeong area were a gable roof type, such as even span, half span, three quarter and the 70.6% of total investigated single-span greenhouses was equipped with a roof ventilation fan while 58.8% had a circulation fan inside the greenhouse. The ratios of roof vent area to floor area in the single-span cucumber greenhouse ranged from 0.61 to 0.96% and in the case of the square roof vent, were higher than that of the circular type vent. On average, the roof ventilation fan in single-span cucumber greenhouse was equipped with the power input of 210W and maximum air volume of $85.0m^3/min$, and the number of fans was 9.75 per a bay. The number of roof vent of single-span oriental melon greenhouse with only roll-up type side vent ranged from 8 to 21 (average 14.8), which was higher than that of other Cucurbitaceae vegetables while the vent number of the greenhouse with a roof ventilation fan was average 7 per a bay.

• 한국자기학회지
• /
• 제24권1호
• /
• pp.22-27
• /
• 2014

자북을 지시하는 방위각 측정용 센서는 항공기와 선박이나 스마트폰 등에 널리 사용되고 있다. 센서의 좌표계가 회전을 하였을 경우도 방위각(azimuth angle) 및 회전각(roll angle)를 지시할 수 있게 하기위하여 3-축의 가속도 센서가 추가로 사용된다. 본 연구에서는 방위각센서에 부착된 3-축의 자기장센서의 특성을 측정하거나, 방위각센서용 3-축의 자기장센서를 개발하기 위하여 3-축의 자기장센서의 방위각 특성을 측정할 수 있는 장치를 개발 제작하였다. 3-축의 자기장발생을 위해서 직경이 290 mm 이상인 3-축의 헬름홀쯔 코일을 사용하여 코일 중심 ${\pm}30mm$ 범위에서 자기장의 분포의 균일도가 0.2 % 이내가 되게 하였다. 비자성실험실이 아닌 일반실험실에서도 실험이 가능하게 소형의 헬름홀쯔 코일과 3-축의 마그네토미터를 사용, 환경자기장(지구자기장+건축물에 의한 자기장)을 보상하고 시험하고자하는 자기장을 컴퓨터 소프트웨어로 제어를 할 수 있게 시험 장치를 고안하였다. 제작된 장치는 자기장을 0.2 % 정확도로, 직각도를 $0.2^{\circ}$, 환경자기장을 10 nT 이하로 보상할 수 있었다. 또한 제작된 장치의 성능검증을 위하여 상용의 방위각센서에 대하여, 그 특성을 측정하여보았다.

• 한국전기전자재료학회논문지
• /
• 제36권5호
• /
• pp.454-462
• /
• 2023

금속 나노 입자의 플래시 램프 어닐링 공정은 빠른 가공 속도(밀리초 단위), 저온 공정, 롤투롤 공정과의 호환성 등 이유로 유연한 기판 위에 고성능 전극을 제조하기 위한 강력한 솔루션으로 제공되어 왔다. 그러나 금속 나노 입자[예를 들면, 금(Au), 은(Ag), 구리(Cu) 등]는 저온 공정을 위한 미세 금속 나노 입자(직경 10 nm 미만)의 제조가 어렵고, 고가이며, 잉크보관 및 플래시 램프 어닐링 과정에서 산화가 발생하는 등의 한계가 존재했다. 이러한 이유로 유기금속화합물 잉크는 금속 나노 입자를 대체할 수 있는 재료로서 저렴한 가격(기존 금속 나노 잉크 대비 1/100의 가격)과 저온 공정성, 높은 재료 안정성으로 인해 제안되었다. 하지만 이러한 장점에도 불구하고, 유기금속화합물의 플래시 램프 어닐링 처리를 통한 유연한 전극의 제조는 광범위하게 연구되지 않고 있다. 본 논문에서는 사전 경험 없이 은 유기금속화합물을 플래시 램프 어닐링하는 과정에서 발생할 수 있는 어려움을 최소화하기 위해 재료 매개변수와 플래시광 처리 매개변수(에너지 밀도, 펄스 지속시간 등)를 고려하여 유연 기판에 전극을 제조하기 위한 최적의 조건을 결정하는 방법을 실험적으로 가이드하고자 한다.

• 대한기계학회논문집A
• /
• 제22권2호
• /
• pp.372-379
• /
• 1998

A new 6 degrees-of-freedom micro stage, based on parallel mechanisms and actuated by using piezoelectric elements, has been developed for the application of micro positioning such as semiconductor manufacturing devices, high precision optical measurement systems, and high accurate machining. The micro stage structure consists of a base platform and an upper platform(stage). The base platform can effectively generates planar motion with yaw motion, while the stage can do vertical motion with roll and pitch motions with respect to the base platform. This separated structure has an advantage of less interference among actuators. The forward and inverse kinematics of the micro stage are discussed. Also, through linearization of kinematic equations about an operating point on the assumption that the configuration of the micro stage remains essentially constant throughout a workspace is performed. To maximize the workspace of the stage relative to fixed frame, an optimal design procedure of geometric parameter is shown. Hardware description and a prototype are presented. The prototype is about 150mm in height and its base platform is approximately 94mm in diameter. The workspace of the prototype is obtained by computer simulation. Kinematic calibration procedure of the micro stage and its results are presented.

• Archives of Plastic Surgery
• /
• 제32권1호
• /
• pp.117-123
• /
• 2005

The reconstructive modalities for vaginal reconstruction include simple dilatation, skin graft, use of intestinal segments and various methods using flaps. However, skin grafting procedure is the most commonly used technique and the McIndoe procedure is a representative technique among skin grafting procedures. McIndoe procedure is easier, faster and has a lower morbidity compared to other techniques. However the conventional McIndoe procedure has several problems such as incomplete vestibule formation, excessive bleeding during dissection, possibility of recto-vaginal or urethro-vaginal fistula formation, late vaginal contracture and discomfort in wearing hard plastic mold for a long time after operation. To solve these problems, the authors modified the conventional McIndoe procedure in several perspectives. The undeveloped vestibule was incised with X-shaped mucosal incision between the urethral opening and posterior margin of the vestibule and deepened by blunt finger dissection to provide a sufficient diameter & length of the neovagina and to minimize bleeding. A sizable medium thickness split skin graft was harvested and wrapped over a roll gauze-filled condom mold. Applying multiple stab incision on the skin grafted condom mold, it was inserted into the prepared neovaginal canal. Distal margin of the skin graft was secured with tips of the mucosal flaps created by X-shaped vestibular incision to prevent accidental extrusion of the skin grafted mold. During last 15 years, we applied this modification to 20 vaginal agenesis patients and investigated results of the 12 patients who could be followed up serially including hematoma formation and skin graft survival rate, size, depth, presence of late contracture, appearance, comfortness, and hygiene of the neovagina. And they were compared with 8 patients of 20 patients who underwent conventional McIndoe procedures. The modified McIndoe procedure revealed lower complication rate, higher patient satisfaction and better functional results.

• 대한기계학회논문집A
• /
• 제37권10호
• /
• pp.1207-1218
• /
• 2013

나달식 등 한쪽 차륜과 레일의 접촉력에 기반한 기존 탈선계수식으로는 열차 주행 시 여러 가지 요인에 의해 발생하는 다양한 유형의 탈선을 이론적으로 예측하기 어렵다. 이를 보완하기 위하여 개발된 단일윤축 탈선계수는 타고오름탈선, 미끄러져오름 탈선, 전복탈선 및 이들의 복합유형 탈선을 잘 예측할 수 있고, 접촉부 마찰계수, 플렌지 각 등 기존의 탈선계수식에서 고려하던 기계적 인자뿐만 아니라 윤중감소/증가, 궤간, 차륜직경, 축상 베어링 위치 등 다양한 탈선영향인자들도 고려할 수 있다. 본 논문에서는 단일윤축 탈선계수식으로 이러한 다양한 탈선영향인자들을 고려하여 기존의 나달식, 바인스톡 식 등으로 구할 수 없었던 탈선현상을 분석한다. 마지막으로 동역학 시뮬레이션을 이용하여 이론적인 단일윤축 탈선계수식 결과들의 타당성을 입증한다.