• 센서학회지
• /
• 제22권1호
• /
• pp.28-37
• /
• 2013

This paper presents a fault-tolerant control technique for wind turbine systems with sensor and actuator faults. The control objective is to maximize power production and minimize turbine loads by calculating a desired pitch angle within their limits. Any fault with a sensor and actuator can cause significant error in the pitch position of the corresponding blade. This problem may result in insufficient torque such that the power reference cannot be achieved. In this paper, a fault-tolerant control technique using a robust dynamic inversion observer and control allocation is employed to achieve successful pitch control despite these faults in the sensor and actuator. The observer based detection method is used to detect and isolate sensor faults by checking whether errors are larger than threshold values. In addition, the control allocation technique is adopted to tolerate actuator fault. Control allocation is one of the most commonly used fault-tolerant control techniques, especially for over-actuated systems. Further, the control allocation method can be used to achieve the power reference even in the event of blade actuator fault by redistributing the lost torque due to erroneous pitch position into non-faulty blade actuators. The effectiveness of the proposed method is demonstrated through simulations with a benchmark model of the wind turbine.

• 한국항해항만학회지
• /
• 제44권5호
• /
• pp.423-429
• /
• 2020

A ship's automatic steering system is the basis for addressing control difficulties related to course-changing and course-keeping during navigation through heading angle control, and is a link in realizing unmanned and autonomous ships. This study proposes a robust RCGA-based linear active disturbance rejection controller (LADRC) design method considering environmental disturbances, measurement noise, and model uncertainties in designing a ship heading controller for use when the ship is sailing. The LADRC consisted of a transient profile, a linear extended state observer, and a PD controller. The control gains in the LADRC with the linear extended state observer were adjusted by RCGAs to minimize the integral of the time-weighted absolute error (ITAE), which is an evaluation function of the control system. The proposed method was applied to ship heading control, and its effectiveness was validated by comparing the propulsive energy loss between the proposed method and a conventional linear PD controller. The simulation results showed that the proposed method had the advantages of lower propulsive energy loss, more robustness, and higher tracking precision than the conventional linear PD controller.

• Journal of Electrical Engineering and Technology
• /
• 제8권6호
• /
• pp.1439-1450
• /
• 2013

This paper investigates a robust neuro-fuzzy control (NFC) method which can accurately follow the speed reference of an interior permanent magnet synchronous motor (IPMSM) in the existence of nonlinearities and system uncertainties. A neuro-fuzzy control term is proposed to estimate these nonlinear and uncertain factors, therefore, this difficulty is completely solved. To make the global stability analysis simple and systematic, the time derivative of the quadratic Lyapunov function is selected as the cost function to be minimized. Moreover, the design procedure of the online self-tuning algorithm is comparatively simplified to reduce a computational burden of the NFC. Next, a rotor angular acceleration is obtained through the disturbance observer. The proposed observer-based NFC strategy can achieve better control performance (i.e., less steady-state error, less sensitivity) than the feedback linearization control method even when there exist some uncertainties in the electrical and mechanical parameters. Finally, the validity of the proposed neuro-fuzzy speed controller is confirmed through simulation and experimental studies on a prototype IPMSM drive system with a TMS320F28335 DSP.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(1)
• /
• pp.274-278
• /
• 2004

This paper presents a strategy to drive built in-type spindle induction motor which is used as CNC (Computer Numerical Control) in the industrial world. The direct vector control which is robust to the changed machine parameters in the high speed range is used in this motor control method. And electrical model of induction motor presents the basic idea based on observer structure, which is composed of voltage model and current model. But the former has the defects in low speed range, the latter has the defects of sensitivity to motor parameter. Thus Gopinath model flux estimator which is the closed loop flux observer based on two models for the rotor flut estimation is used in this paper. Moreover this paper presents to drive the spindle motor in the high speed range by using the flux weakening control.

• 전기전자학회논문지
• /
• 제9권1호
• /
• pp.47-56
• /
• 2005

본 연구에서는 불확실성과 부하 변동 하에 브러쉬없는 직접구동 전동기의 정확한 사전결정 추적성능을 제공하기 위한 새로운 개선된 강인한 가변구조 추적 제어기를 설계하였다. 리칭 페이즈를 제거하기 위한 특수 적분 슬라이딩 변은 서보 전동기의 초기 위치부터 이상 슬라이딩 모드와 가상 이상 슬라이딩 궤적을 정의한다 . 영이 아닌 슬라이딩 면에 의하여 발생되는 추적오차를 유도하였다. 외란 관측기를 갖는 연속 입력을 제안하여 불확실성과 부하 변동 하에 사전 결정 가상 이상 슬라이딩 궤적을 사전 값 내에 추적하도록 한다. 제안된 알고리듬의 유용성을 부하 변동 하에 브러쉬없는 직접구동 전동기에 대한 비교 시뮬레이션으로 입증한다.

• 드라이브 ㆍ 컨트롤
• /
• 제18권4호
• /
• pp.52-58
• /
• 2021

The variable structure controller is designed such that in sliding mode, the system moves along the switching plane in the vicinity of the switching plane, thus it is robust because it is not affected by the parameter fluctuations of the plant. However, a controller based on a variable structure may not meet the desired performance when it is commanded to track any input or is exposed to disturbances. This study proposes a sliding mode controller that follows the IVSC (Integral Variable Structure Control) approach with ELO (Extended Luenberger observer) to solve this problem. The proposed sliding mode control is applied to the velocity control of the hydraulic motor. The sliding plane was determined by the pole placement, and the control input was designed to ensure the existence of the sliding mode. The feasibility of modeling and controller are reviewed by comparing with conventional proportional-integral control through computer simulation using MATLAB software and experimenting on the cases of significant plant parameter fluctuations and disturbances.

• 전력전자학회논문지
• /
• 제12권2호
• /
• pp.157-164
• /
• 2007

본 논문에서는 일반적인 브러시리스 전동기의 센서리스 구동 성능을 개전하기 위한 퍼지 역기전력 관측기를 이용한 새로운 센서리스 구동 방법이 제안되었다. 기존의 브러시리스 전동기의 센서리스 구동 방법은 저속영역과 과도상태에서의 성능저하와 추가적인 회로를 필요로 한다. 이러한 문제점을 보완하기 위해 사다리꼴 형태의 역기전력을 추정하기 위해 적합한 퍼지 논리에 의해 브러시리스 전동기의 역기전력을 정확하게 추정하였다. 퍼지 역기전력 관측기를 이용한 제안된 알고리듬은 정상 상태 뿐만 아니라 과도 상태에서도 연속적인 회전자 위치를 추정하고 외부 환경 변화에 강인한 제어를 얻을 수 있다. 제안된 알고리듬의 우수성은 다른 센서리스 구동방법과 비교한 시뮬레이션을 통하여 입증되었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.324-327
• /
• 1996

This paper describes the robust controller design methods applied to the problem of an automatic system for tow-vehicle/trailer combinations. This study followed an inverse Linear Quadratic Regulator(LQR) approach which combines pole assignment methods with conventional LOR methods. It overcomes two concerns associated with these separate methods. It overcomes the robustness problems associated with pole placement methods and trial and error required in the application of the LQR problem. Moreover, a Kalman filter is used as the observer, but is modified by using the loop transfer recovery (LTR) technique with modified transmission zero assignment. The proposed inverse LQG,/LTR controllers enhances the forward motion stability and maneuverability of the combination vehicles. At high speeds, where the inherent yaw damping of the vehicle system decreases, the controller operates to maintain an adequate level of yaw damping. At backward moton, both 4WS (2WS tow-vehicle, 2WS trailer) and 6WS (4WS tow-vehicle, 2WS trailer) control laws are proposed by using inverse LQG/LTR method. To evaluate the stability and robustness of the proposed controllers, simulations for both forward and backward motion were conducted using a detailed nonlinear model. The proposed controllers are significantly more robust than the previous controllers and continues to operate effectively in spite of parameter perturbations that would cause previous controllers to enters limit cycles or to loose stability.

• 전자공학회논문지
• /
• 제52권5호
• /
• pp.214-221
• /
• 2015

본 논문에서는 측정 잡음에 의해서 출력 신호가 왜곡된 이산 시간 선형 스위치드 시스템의 스위칭 신호와 상태 변수를 관측하기 위한 강인한 추정 및 검출 기법을 제시한다. 첫째, 최소 거리 기준에 기초한 작동 모드 추정 알고리즘이 제안된다. 이 과정에서 모드의 추정값을 얻게 되고, 이를 이용하여 상태 변수 또한 관측할 수 있게 된다. 둘째, 주어진 스위치드 시스템의 작동 모드 변화 시점, 즉, 스위칭이 언제 발생하는지 검출하는 알고리즘이 고안된다. 시스템에 인가되는 측정 잡음이 유계라는 가정 하에, 제안된 추정 알고리즘은 주어진 스위치드 시스템의 작동 모드를 정확하게, 그리고 상태 변수를 근사적으로 추정하며, 검출 알고리즘은 실제 스위칭이 발생한 후, 미리 정해진 지연 시간이 지나가기 전에 스위칭 시간을 검출할 수 있다.

• Journal of Power Electronics
• /
• 제15권5호
• /
• pp.1244-1255
• /
• 2015

This paper presents a new multi-machine robust control based on an electric differential system for electric vehicle (EV) applications which is composed of four in-wheel permanent magnet synchronous motors. It is based on a new master-slave direct torque control (DTC) algorithm, which is used for the control of bi-machine traction systems based on a speed model reference adaptive system observer. The use of an electric differential in the design of a new EV constitutes a technological breakthrough. A classical system with a multi-inverter and a multi-machine comprises a three-phase inverter for each machine to be controlled. Another approach consists of only one three-phase inverter for several permanent magnet synchronous machines. The control of multi-machine single-inverter systems is the subject of this study. Several methods have been proposed for the control of multi-machine single-inverter systems. In this study, a new master-slave based DTC strategy is developed to generate an electric differential system. The entire system is simulated by Matlab/Simulink. The simulation results show the effectiveness of the new multi-machine robust control based on an electric differential system for use in EV applications.