• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.4
• /
• pp.723-730
• /
• 2015

In this paper, a location tracking compensation algorithm based on the Least-Squares Method ($LCA_{LSM}$) was proposed to improve the autonomous tracking efficiency for the docent robot in exhibition hall, and the performance of the $LCA_{LSM}$ is analyzed by several practical experiments. The proposed $LCA_{LSM}$ compensates the collected location coordinates for the robot using the Least-Squares Method (LSM) in order to reduce the cumulated errors that occur in the Encoder/Giro sensor (E/G) and to enhance the measured tracking accuracy rates in the autonomous tracking of the robot in exhibition hall. By experiments, it was confirmed that the average error reduction rates of the $LCA_{LSM}$ are higher as 4.85% than that of the $LCA_{KF}$ in Scenario 1 (S1) and Scenario 2 (S2), respectively on the location tracking. In addition, it was also confirmed that the standard deviation in the measured errors of the $LCA_{LSM}$ are much more low and constant compared to that of the E/G sensor and the $LCA_{KF}$ in S1 and S2 respectively. Finally, we see that the suggested $LCA_{LSM}$ can execute more the stabilized location tracking than the E/G sensors and the $LCA_{KF}$ on the straight lines of S1 and S2 for the docent robot.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.8
• /
• pp.752-759
• /
• 2008

In this paper, we propose a high accurate geo-location system based on a single base station, where its location is obtained by Time-of-Arrival(ToA) and Direction-of-Arrival(DoA) of the radio signal. For estimating accurate ToA and DoA information, a MUltiple SIgnal Classification(MUSIC) is adopted. However, the estimation of ToA and DoA using MUSIC algorithm is a time-consuming process. The position tracking bias is occurred by the time delay caused by the estimation process. In order to mitigate the bias error, we propose the estimation method of the position tracking bias and compensate the location error produced by the time delay using the position tracking bias mitigation. For accurate self-localization of mobile robot, the Unscented Kalman Filter(UKF) with position tracking bias is applied. The simulation results show the efficiency and accuracy of the proposed geo-location system and the enhanced performance when the Unscented Kalman Filter is adopted for mobile robot application.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.11
• /
• pp.883-887
• /
• 2016

Navigating an unknown environment is a challenging task for a robot, especially when a large number of obstacles exist and the odometry lacks reliability. Pose tracking allows the robot to determine its location relative to its previous location. The ICP (iterative closest point) has been a powerful method for matching two point clouds and determining the transformation matrix between the maps. However, in a situation where odometry is not available and the robot moves far from its original location, the ICP fails to calculate the exact displacement. In this paper, we suggest a method that is able to match two different point clouds taken a long distance apart. Without using any odometry information, it only exploits the features of corner points containing information on the surroundings. The algorithm is fast enough to run in real time.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.795-800
• /
• 2008

The paper presents research for the established experiment environment of multi vehicle robot, localization algorithm that is based on vehicle control, and path tracking. The established experiment environment consists of ultrasonic positioning system, vehicle robot, server and wireless module. Ultrasonic positioning system measures positioning for using ultrasonic sensor and generates many errors because of the influence of environment such as a reflection of wall. For a solution of this fact, localization algorithm is proposed to determine a location using vehicle kinematics and selection of a reliable location data. And path tracking algorithm is proposed to apply localization algorithm and LOS, finally, that algorithms are verified via simulation and experimental

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3_1spc
• /
• pp.607-614
• /
• 2013

This paper proposes a robot driving system and sensor implementation for use with an education robot. This robot has multiple functions and was designed so that children could use it with interest and ease. The robot recognizes the location of a user and follows that user at a specific distance when the robot and user communicate with each other. In this work, the robot was designed and manufactured to evaluate its performance. In addition, an embedded board was installed with the purpose of communicating with a smart phone, and a camera mounted on the robot allowed it to monitor the environment. To allow the robot to follow a moving user, a set of sensors combined with an RF module and ultrasonic sensors were adopted to measure the distance between the user and the robot. With the help of this ultrasonic sensors arrangement, the location of the user couldbe identified in all directions, which allowed the robot to follow the moving user at the desired distance. Experiments were carried out to see how well the user's location could be recognized and to investigate how accurately the robot trackedthe user, which eventually yielded a satisfactory performance.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.3
• /
• pp.329-334
• /
• 2011

This paper presents the method for location estimation with obstacle tracking method. A laser scanner is used to implement the system, and we assume that the map information is known. We matches the measurement of the laser scanner to estimate the location of the robot by using sequential monte carlo (SMC) method. After estimating the robot's location, the pose of obstacles are detected and tracked, hence, we can predict the collision risk of them. Finally, we present the experiment results to verify the proposed method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2502-2507
• /
• 2003

In this paper, a crack sealing robot is developed. The crack sealing robot is built to detect, track, and seal the crack on the pavement. The sealing robot is required to brush all dirt in the crack out for preparing a better sealing job. Camera calibration has been done to get accurate crack position. In order to perform a cleaning job, the explicit force control method is used to regulate a specified desired force in order to maintain constant contact with the ground. Experimental studies of force tracking control are conducted under unknown environment stiffness and location. Crack tracking control is performed. Force tracking results are excellent and the robot finds and tracks the crack very well.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.6
• /
• pp.1245-1254
• /
• 2011

This paper proposes a target tracking algorithm for wheeled mobile robots using in various fields. For the stable tracking, we apply a vision system to a mobile robot which can extract targets through image processing algorithms. Furthermore, this paper presents an algorithm to position the mobile robot at the desired location from the target by estimating its relative position and attitude. We show the problem in the tracking method using the Position-Based Visual Servo(PBVS) control, and propose a tracking method, which can achieve the stable tracking performance by combining the PBVS control with Image-Based Visual Servo(IBVS) control. When the target is located around the outskirt of the camera image, the target can disappear from the field of view. Thus the proposed algorithm combines the control inputs with of the hyperbolic form the switching function to solve this problem. Through both simulations and experiments for the mobile robot we have confirmed that the proposed visual servo control method is able to enhance the stability compared to of the method using only either PBVS or IBVS control method.

• Journal of information and communication convergence engineering
• /
• v.10 no.4
• /
• pp.390-395
• /
• 2012

This paper describes an implementation of automatic mutual localization of swarm robots using a particle filter. Each robot determines the location of the other robots using wireless sensors. The measured data will be used for determination of the movement method of the robot itself. It also affects the other robots' self-arrangement into formations such as circles and lines. We discuss the problem of a circle formation enclosing a target that moves. This method is the solution for enclosing an invader in a circle formation based on mutual localization of the multi-robot without infrastructure. We use trilateration, which does require knowing the value of the coordinates of the reference points. Therefore, specifying the enclosure point based on the number of robots and their relative positions in the coordinate system. A particle filter is used to improve the accuracy of the robot's location. The particle filter is operates better for mutual location of robots than any other estimation algorithms. Through the experiments, we show that the proposed scheme is stable and works well in real environments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.4B
• /
• pp.300-308
• /
• 2012

Many indoor location tracking technologies have been proposed. Generally indoor location tracking using TOA signal is used, there is a weak point that it's difficult to track the location due to obstacles like a refraction, reflection and dispersion of radio wave. In this paper, we apply ETOA(Estimated-TOA) algorithm in NLOS(Non-Line-Of-Sight) environment to solve above problem. In NLOS environment, TOA value between Beacon and Mobile node is predicted by ETOA algorithm and the tracking of indoor location is also possible to identify using two NLOS beacons of three beacons by this algorithm. We show that the proposed algorithm is accurate location tracking is accomplished using the applying the proposed algorithm to indoor moving robot and the inertia sensor of robot and Kalman filter algorithm.