• International Journal of Highway Engineering
• /
• v.19 no.5
• /
• pp.33-42
• /
• 2017

PURPOSES : The purpose of this study is to suggest the construction and quality control method for the re-repair of a deteriorated partial depth repair for sections of Portland cement concrete pavement. METHODS : An experimental construction was conducted to extend the repair width for removing an existing repair section. A removal method was used to ensure early performance for a deteriorated partial depth repair section. Bond strength and split tensile strength were measured at the near vertical interface layer between the existing pavement and repair material. The area was analyzed for various conditions such as the extended repair area and the removing method of the existing repair section. RESULTS : As a result of analysis of bond strength and split tensile strength, the bonding performance of a milling removed section was improved over a cutting and hand breaker removed section. The bond strength was analyzed to increase slightly as the extended repair width for removing the existing repair section increased. The split tensile strength did not show a clear relationship to an increased extended repair width of an existing removed repair section. CONCLUSIONS : The milling removal method should be applied in the removal of existing deteriorated partial depth repair sections. The extended repair width for a re-repair section should be wider than the existing partial depth repair with at least a 75-mm length and width for the bond strength and the split tensile strength.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.107-122
• /
• 2015

PURPOSES : The use of virtual driving tests to determine actual road driving behavior is increasing. However, the results indicate a gap between real and virtual driving under same road conditions road based on ergonomic factors, such as anxiety and speed. In the future, the use of virtual driving tests is expected to increase. For this reason, the purpose of this study is to analyze the gap between real and virtual driving on same road conditions and to use a calibration formula to allow for higher reliability of virtual driving tests. METHODS : An intelligent driving recorder was used to capture real driving. A driving simulator was used to record virtual driving. Additionally, a virtual driving map was made with the UC-Win/Road software. We gathered data including geometric structure information, driving information, driver information, and road operation information for real driving and virtual driving on the same road conditions. In this study we investigated a range of gaps, driving speeds, and lateral positions, and introduced a calibration formula to the virtual record to achieve the same record as the real driving situation by applying the effects of the main causes of discrepancy between the two (driving speed and lateral position) using a linear regression model. RESULTS: In the virtual driving test, driving speed and lateral position were determined to be higher and bigger than in the real Driving test, respectively. Additionally, the virtual driving test reduces the concentration, anxiety, and reality when compared to the real driving test. The formula includes four variables to produce the calibration: tangent driving speed, curve driving speed, tangent lateral position, and curve lateral position. However, the tangent lateral position was excluded because it was not statistically significant. CONCLUSIONS: The results of analyzing the formula from MPB (mean prediction bias), MAD (mean absolute deviation) is after applying the formula to the virtual driving test, similar to the real driving test so that the formula works. Because this study was conducted on a national, two-way road, the road speed limit was 80 km/h, and the lane width was 3.0-3.5 m. It works in the same condition road restrictively.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.38 no.4
• /
• pp.137-146
• /
• 1996

This paper presents the results of field experience from an experimental pavement construction on a low volume road using recycled concrete. The recycled concrete was prepared by replacing a half of coarse aggregate with recycled aggregate. Virgin natural sand was used as fine aggregate together a plasticizer and a fly ash (0.8% and 5% by wt. of cement, respectively). The load bearing capacity of the subbase made of recycled aggregate was acceptable. The length, thickness and width of the pavement were l00m, 20cm and 3m, respectively. From construction experience, it was found that workability and finishability of the recycled concrete mixture were relatively poor, but strengths were satisfactory. Flexural strength, compressive strength and elastic modulus at 28 days were 54Kg/$cm^2$, over 250Kg/$cm^2$, and 220,OOOKg/$cm^2$, respectively. The construction could be performed by hand without much difficulty. The surface was finished smoothly by wet fabric and only minor cracks were found on the surface.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.698-704
• /
• 2007

Articulated vehicles which have a pivoting joint allowing the vehicle to rotate more easily are difficult to turn the curves because of their long length. In order to review operational safety, turning characteristics related to geometric design should be investigated when articulated vehicles run on the road which can be interfered with other vehicles. The vehicles to review the turning characteristics are the normal articulated bus in Seoul with FWS(front wheel steering) and new bimodal tram with AWS(all wheel steering). Steering characteristics and geometric design were investigated such as turning radius, offtracking, swept path width and swingout. The results were reviewed with respect to the standards of vehicle safety and road design.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.04a
• /
• pp.388-393
• /
• 1996

This study evaluated characteristics and performance of recycled concrete as a pavement which was constructed on a low volume road. The recycled concrete was prepared by replacing a half of coarse aggregate with recycled aggregate. Natural sand from a source was used as fine aggregate together with admixtures such as plasticizer and fly ash (0.8% and 5% by wt. of cement, respectively). The length, thickness and width of the pavement were 100mm, 20cm and 3m, respectively. From construction experience, it was found that workability and finishability of the recycled concrete mixture were relatively poor, but strengths were satisfactory. Flexural strength, compressive strength and elastic modulus at 28 days were approximately 45Kg/$\textrm{cm}^2$, 250Kg/$\textrm{cm}^2$, and 240,000 Kg/$\textrm{cm}^2$, respectively. The pavement could be constructed by hand without much difficulty. The surface was finished smoothy by wet fabric and only minor cracks were found on the surface.

• Journal of Environmental Impact Assessment
• /
• v.20 no.5
• /
• pp.697-703
• /
• 2011

The purpose of this study aims to preserve biodiversity in increasingly fragmented green patches for spatial analysis of planting on the eco-corridors and to optimize the target species, the location, width, cross section of the eco-corridors. It was suggested that eco-corridors should have to planned at early stages of road planning so that the number and locations of eco-corridors in advance. Ecological corridor is the facility to connect two habitats fragmented by road, dam, housing and industrial area. And, everyone agree that ecological corridor is important useful structural component that help animal movement in fragmented landscapes. However, ecological corridors have many problems of the recorded the size of corridor, planting species to nearby exiting vegetation species and structure. The most important facts that there are no consideration for location of animal migration and behavior using eco-corridors. This study was carried out to spatial analysis of eco-corridors location, satellite data and GIS were used to analyze for searching optimum location of the eco-corridors.

• Journal of the Korean Institute of Rural Architecture
• /
• v.15 no.4
• /
• pp.43-50
• /
• 2013

This study is to clarify the characteristics and its change of spatial elements for community focused on the existing 22 old settlements in urban area of Cheongju. These community spaces are mainly divided into three parts, that is central space, inner road, and blind alley(cul-de-sac). The transitional characteristics of them are as follows. Firstly, the characteristics of central spaces is lasting, but the function is influenced by changing times. The function of central spaces located at the entrance to the village had been reduced to adjustments to modern lifestyle, and currently changed into senior citizen community center, supermarket, and public area. Secondly, as the width of the existing inner roads passed through old settlements had been extended, they are changed into pedestrian and traffic road, but the shape and function of them have been maintained. When new roads passed through old settlements had been established, the shape of old inner roads is disappeared, and the function of them is changed into byway and alley. Thirdly, cul-de-sacs of old settlements have tended to create a sense of community, but new cul-de-sacs formed by lot division have been only changed to passage. When new roads are established and cul-de-sacs are changed into alleys, the community between individual households is lost.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.88-94
• /
• 2004

Recently, vehicle simulators are widely used to evaluate driver's responses and driver assistance systems. It needs much effort to construct the virtual driving environment for a vehicle simulator. In this study, it is described how to make effectively the roads and the driving environment for a vehicle simulator. The GIS (Geographic Information System) is used to construct the roads and the environment effectively. Because the GIS is the integrated system of geographical data, it contains useful data to make virtual driving environment. First, the outline and centerline of roads is abstracted from the GIS. From the road outline, the road width is calculated. Using the centerline, the grid model of roads is constructed. The final graphic model of roads is constructed by mapping road image to the grid model according to the number of lanes and the kind of surface. Data of buildings from the GIS are abstracted. Each shape and height of buildings is determined according to kind of buildings, the final graphic model of buildings is constructed. Then, the graphic model of roadside tree is also constructed. Finally, the driving environment for driving simulator is constructed by converting the three graphic models with the graphic format of Direct-X and by joining the three graphic models.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.725-730
• /
• 2005

In case of the national roads which is opened in the past, there are carried out the expansion and improvement for enlargement of the traffic demand by industrial development and safety road operation to narrow of road width and serious change of the road alignment with effect of topography and graphical features of a mountain. A protection method using vegetation in the cut-slope has been constructed for harmony of ambient environment after cutting the slope recently. But it requires a study because the surface lose and the failure have been occurred in the large cut-slope which is covered by vegetation. In this study it was presented a countermeasure and examined a stability of contained uncertainty in the cut-slope according to the failure example of the cut-slope which is covered by vegetation. The additional research will be necessary against the development of the investigation technique which executes the stability investigation of the cut-slope which is covered by vegetation.

• Journal of Korean Society for Geospatial Information Science
• /
• v.10 no.4 s.22
• /
• pp.77-84
• /
• 2002

Recently, damage of pavement represented by crack is depened by the increase of traffic demand up to ten million and wight, and interest about the efficient management of pavement is being increased gradually according to the growth of maintenance expense of road surface. In this study, the possibility of application for acquisition of crack information was tested by appling DCRP and digital image processing technique and measuring crack on road surface precisely. Based on this, objective and efficient road surface measurement was planned and done. Measuring crack width, acquire result of comparative high accuracy. So, it is considered that it can be utilized as plan draft data for deterioration estimation and repair reinforcement work of pavement.