• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.166-173
• /
• 2002

The wheel bearing hub unit is developed type of wheel bearing unified with the hub parts. It has advantage of reducing the weight and the number of components. And, it also improves uniformity of manufacturing quality, In order to design the wheel bearing hub units, many techniques are used such as load analysis, structure analysis and bearing characteristics analysis and so forth. These techniques need highly accurate load conditions founded on service conditions. In this study, to design the wheel bearing hub units used widespread in passenger cars, the service load was measured through driving tests on the public roads and in the special events. The public roads are classified into highway, intercity road, rural road, urban road, and unpaved road so as to know what the characteristics of the road loads are. The results of the tests showed that the wheel force was relative to the lateral acceleration, and also could be calculated from the lateral acceleration. The lateral acceleration was measured from 0.0G to 0.6G in general driving on the public roads, with different distributions in each road type. In special events, the maximum lateral acceleration was measured from 0.8G to 1.3G.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.5
• /
• pp.512-519
• /
• 2016

In this study, the tire road friction estimation(TRFE) algorithm for controlling the rear wheel driving force of a 4WD vehicle during acceleration is developed using a standard sensor in an ordinary 4WD passenger car and a speed sensor. The algorithm is constructed for the wheel shaft torque, longitudinal tire force, vertical tire force and maximum tire road friction estimation. The estimation results of shaft torque and tire force were validated using a torque sensor and wheel force transducer. In the algorithm, the current road friction is defined as the proportion calculated between longitudinal and vertical tire force. Slip slop methods using current road friction and slip ratio are applied to estimate the road friction coefficient. Based on this study's results, the traction performance, fuel consumption and drive shaft strength performance of a 4WD vehicle are improved by applying the tire road friction estimation algorithm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.205-215
• /
• 2001

In this study, modeling and analysis procedure for the dynamic analysis of a high mobility tracked vehicle system were studied. The vehicle model used in this investigation is assumed to be consist of two kinematically decoupled subsystems. The chassis subsystem consists of chassis frame, sprocket, support rollers, road wheels, idler wheel, road wheel arms and idle wheel arm, while the track subsystem is represented as a closed kinematic chain consisting of track links and end connectors interconnected by revolute joints with bushing. Nonlinear contact force module describing the interaction between track link, and sprocket, idler wheel, road wheel, support roller, ground was used. The effects of road wheel arms and idler wheel arm due to tension adjuster are also considered.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.12-18
• /
• 2014

This paper describes about the development of new concept's rear wheel guards for the reduction of Road Noise in the passenger vehicle using test. The new wheel guards are proposed by various frequency chamber concept and different textile layers concept. Two wheel guards were verified by small cabin resonance test and vehicle test. Through new developing process without vehicle test, Result of road noise will be expected when new concepts and materials of wheel guard is applied into automotive vehicle. As a result of the application of Aimed Helmholtz and Multi-layers concept, this paper classifies the road noise, cost and weight are reduced by new concepts and the solutions are adopted into the 2 cars.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.612-617
• /
• 2014

It is generally known that the automotive road wheel involves the non-proportional multiaxial loading condition, therefore the measuring dynamic stress and strain in driving state is very important to predict an endurance characteristic of the automotive road wheel. In this study, the ultimate driving test using F1 circuit with respect to 2 kinds of velocity conditions have been carried out in order to measure dynamic stress, strain of the wheel and acceleration of a vehicle. Based on the measured results, the characteristics of dynamic stress generation have been analyzed, and factors which have effect on the dynamic stress generation have been studied.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.78-85
• /
• 2013

This paper presents the sliding mode control methods for anti-lock brake system (ABS) with the friction force observer. Using a simplified quarter car model, the sliding mode controller for ABS is designed to track the desired wheel slip ratio. Here, new method to find the desired wheel slip ratio which produces the maximum friction force between road and tire is suggested. The desired wheel slip ratio is varying according road and tire conditions to produce maximum friction force. In order to find optimum desired wheel slip ratio, the sliding mode observer for friction force is used. The proposed sliding mode controller with observer is evaluated in simulation, and the control design is shown to have high performance on roads with constant and varying adhesion coefficients.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.517-523
• /
• 2004

Recently, wheel slip controllers with controlling the wheel slip directly has been studied using the brake-by-wire actuator. The wheel slip controller is able to control the braking force more accurately and can be adapted to various different vehicles more easily than the conventional ABS systems. The wheel slip controller requires the information about the tire braking force and road condition in order to achieve the control performance. In this paper, the tire braking forces are estimated considering the variation of the friction between brake pad and disk due to aging of the brake, moisture on the contact area or heating. In addition, the road friction coefficient is estimated without using tire models. The estimated performance of tire braking forces and the road friction coefficient is evaluated in simulations.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.3
• /
• pp.47-52
• /
• 2011

A tracked vehicle is dependent on performance of power pack and suspension systems. Especially, road wheels which are components of suspension system contribute distributing vehicle weight on soil and preventing from misguiding tracks. In this study, the maximum force was calculated that a tracked vehicle is driven on the worst condition. And then, FE analyses were carried out to evaluate strength road wheel under maximum force condition. In standard of quality evaluation for road wheel, FE simulations and experimental works were carried out under thirty degree slant load of normal direction of shaft. And then, A relationship residual deformation for slant load was investigated. The result of this research is applicable to evaluate strength and to make use of basis data.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.73-79
• /
• 1998

For the design and development of the wheel type excavator, the dynamic effects of travelling on the performance of the equipment should be first analyzed and conside- red in the initial design stage. In order to test the durability of the equipment in a short period, th travelling test should be performed over accelerated durability test tracks. which is more severe than general field roads such as city road, paved road, unpaved road and rough road. In this paper, a parametric study is performed in order to determine important design parameters of durability test track of a wheel type excavator. A rigid body model is developed using DADS and dynamic analysis is performed for the equipment travelling over several test roads with different severity. A comparison of test and analysis results is also presented.

• Transactions of Materials Processing
• /
• v.23 no.2
• /
• pp.116-121
• /
• 2014

Low pressure die casting and flow forming have been successfully used to produce sound road wheels from magnesium alloy AM80. In the current study, high speed compression testing was initially conducted to simulate the flow forming of a Mg wheel. Subsequently the flow forming was simulated with "Forge$^{TM}$", an FEM software package. On the basis of flow forming simulations, the flow forming of the Mg wheel was performed under different conditions. For the flow forming experiments, the preform castings were made by low pressure die casting from AM80, a commercial magnesium alloy. In flow forming of the magnesium preform wheel, the flow forming of the Mg wheel was successfully accomplished when the feed rate was less than half that for the forming of an aluminum road wheel. The reduction in feed rate was 52%. Finally, a comparison with the flow forming simulations was made.