• 한국산학기술학회논문지
• /
• 제15권12호
• /
• pp.6967-6972
• /
• 2014

기계적 체결 방식으로 볼트와 너트를 이용한 결합 방식과 리벳이나 핀이 널리 사용되고 있다. 압입 방식은 다른 생산방법에 비하여 쉽게 가공 가능하며 재료의 인성이 우수하다. 하지만 실제적으로 압입방식으로 생산하는 과정에서 균열이 발생될 수 있는 경우가 많다. 따라서 본 연구에서는 CATIA 프로그램을 이용하여 핀이 PCB 판으로 들어가고 나가는 두 가지 경우의 모델을 만들고 ANSYS 프로그램을 이용하여 유한요소 해석을 수행하였다. Case 1 및 2의 경우에 핀이 PCB판에 들어갈 때, PCB판에서 작용되는 최대 하중은 각각 79.708N과 90.277N이다. 그리고 Case 1 및 2의 경우에, PCB판이 Pin에서 빠져나올 때의 최대 하중은 각각 63.783N과 33. 75N으로 각각 나타났다. 본 연구의 결과를 실제 압입 공정의 설계에 응용한다면 그 파손방지 및 내구성을 평가하는 데에 활용이 클 것으로 사료된다.

• 한국농공학회지
• /
• 제27권4호
• /
• pp.42-52
• /
• 1985

This study was attempted to derivate empirical formulas for the runoff: ratio during ilood. season at three watersheds of Dan Yang, Chung Ju, and Yeo Ju are located at upper, middle, and lower portion of Nam Han river basin, respectively. Obtained formulas for flood runoff ratio can be applied as an element for the estimation, peak discharge for the design of various hydraulics structures which can be concidented with meteorological and topographical condition. The obtained through this study were analyzed as follows. 1.It was found that the magnitude of runoff ratio depends on the amount of rainfall for all studying basins. 2.Empirical formulas 'for the runoff' ratio were derivated as 1- 2,707 Rt0.345, 1-1.691 Rt0.242 and 1-1.807 Rt0.227 at Dan Yang, Chung Ju and Yeo Ju watershed, respectively. 3.The magnitude of runoff ratio was appeared in the order of Dan Yang, Chung Ju, and Yeo Ju are located at upper, middle and lower portion of Nam Han rivet basin, respectively. 4.It was assumed that in general the more it rains, the lesser becomes the ratio of loss rainfall. Especially, the ratio of loss rainfall for Dan Yang, upper portion of river basin was shown as the lowest among three watersheds. Besides, the magnitude of that was appeared in the order of Chung Ju and Yeo Ju watershed located at middle, and lower part of river basin, respectively. 5.Relative and standard errors of runoff ratio calculated by empirical formulas were shown to be within ten percent to the observed runoff ratio in all watersheds. 6.It is urgently essential that the effect of antecedent rainfall have an influence on the next coming flood should be studied in near future.

• 한국환경과학회지
• /
• 제15권11호
• /
• pp.1017-1025
• /
• 2006

This study was conducted to evaluate characteristic of water duality in coastal sea of Incheon using a multivariate analysis. The analysis data in coastal sea of Incheon was aquired by the NFRDI data which was surveyed from March 1997 to November 2003. Eleven water quality parameters were determined on each survey The results were summarized as follow : Water quality in Incheon coastal sea could be explained up to 64.62% by three factors which were included in loading of fresh water and nutrients by the land(36.98%), seasonal variation(16.19%), and internal metabolism (11.24%). The results of time series analysis by factor score, in case of factor 1, station 1 influenced by Han river was shown to high factor score and station 3 located by outer sea was shown to low factor score. In case of factor 2, station 1 was appeared to high variation and station 3 was appeared to low variation. The result of cluster analysis by station was classified into three group that has different water quality characteristics. Especially, station 1 which affected by Han river and station 4 which affected by sewage treatment plant was appeared to considerable water quality characteristics against other station. In yearly cluster analysis, three group was classified and water quality in 2003 years due to high precipitation was different to another year. It could be suggested from these results that it is important to control discharge of fresh water by Han rivet and sewage treatment plant for water quality management of coastal sea of Incheon.

• 소음진동
• /
• 제8권1호
• /
• pp.57-74
• /
• 1998

구조체의 연결부위에서 미지의 결합강성으로 인하여, 실험과 유한 요소법으로 구한 모달 매개변수들은 종종 일치하지 않는다. 본 논문은 실험으로 추출된 동특성 데이타에 근거하여, 해석적인 방법을 통해 새로운 모델링 방법을 제시하고 있다. 대표적인 연결방법으로 리벳을 이용한 Lap이음보에서 동강성을 측정하기 위한 비선형 진동실험이 제안 되었으며, 이를 Lap 이음판에 적용하기 위하여 동강성에 해당하는 설계변수로서 빔요소를 도입하였다. 이 유한요소 모델링은 범용 패키지인 PATRAN과 ABAQUS를 사용하였으며, 빔요소의 직경을 실험치의 고유진동수와 일치하도록 조절함으로써 직경의 최적치 경향을 관찰하였다. 제시된 모델링 기법과 기존의 모델링 기법으로 얻은 결과치들을 실험치와 비교하였다.

• 한국수산과학회지
• /
• 제33권6호
• /
• pp.585-590
• /
• 2000

A hemolysin producing strain was isolated from Kum rivet estuary located in west part of Korea. In the process of identification the isolated strain was similar to V. mimicus but did not show characteristics of known Vibrio species; therefore, the strain was designated as Vibrio sp. D9 ( V. kumkang) tentatively and further identification study was carried out by comparing its bacteriological characteristics, Morphologically Vibrio sp. D9 was a typical straight roe with a polar flagellium. Among known Vibrio species no identical strains were found when using automatic bacteria identification system ($MicioLog^(TM)$system, release 4.0, Biolog Inc., USA) which evaluated the ability of metabolizing 95 kinds of carbon and nitrogen sources. Vibrio sp. D9 showed 18 and 13 different responses as compared to V. mimicus and V. cholerae, respectively. Clear hemolysis zones were observed with the strain against human and sheep blood agar plate, Hemolytic toxicity was confirmed by strong vascular permeability and fatal toxicity against mouse was also observed. Thus the strain was a pathogenic vibrio. Growth conditions for Vibrio sp. D9 were salinity of $0{\~}5.0{\%}$, pH of $6.4{\~}9.8$, temperature of $15{\~}41^{\circ}C$, respectively.

• 박물관보존과학
• /
• 제7권
• /
• pp.11-24
• /
• 2006

판갑은 고대의 무기와 철제품 제작기술을 그대로 반영하는 중요한 문화재이다. 철제갑옷 중 횡장판갑의 출토사례는 매우 드물며 망이산성 출토 판갑처럼 그 형태가 완형인 유물은 그리 많지 않다. 이번 보고서에서는 응용 가능한 비파괴 방사선 조사에 의한 횡장판갑의 방사선사진 및 과학적 보존처리를 통하여 나타나는 고대 판갑제작기술을 검토해 보았다. 7단 구성의 망이산성 출토 판갑은 고리경첩으로 우전동이 개폐되는 형식이다. X-선 사진의 판독결과 판겹침과 천공간격으로 고대판의 철포복륜 및 우측협부의 혁포복륜이 확인되었으며, 착장시 어깨걸이를 연결한 것으로 보이는 투공도 관찰되었다. 특히 천공과 병뉴기법에 있어, 하나의 병이 세판 이상을 연접하는 것을 피하고 있음을 확인하였다. 이는 기술적인 한계를 극복하고 판갑의 기능을 살렸음을 보여주는 중요한 자료이다.

• 한국전산구조공학회논문집
• /
• 제29권6호
• /
• pp.491-498
• /
• 2016

리벳이나 볼트가 결합되는 구멍은 항공기, 선박 및 기타 구조물에 사용되는 판재의 응력 집중을 유발한다. 과도한 응력 집중 현상이 지속되면 종래에는 파단이 일어날 수 있으므로 설계 단계에서 응력 집중 현상의 명확한 해석이 중요하다. 이 논문에서는 판재위에 리벳을 배치하는 간단한 최적화 방법이 제시되었다. 첫째로 응력 집중 현상 해석에서 FEM 구조 해석이 얼마나 정확한지 검증하였다. 평판 위에 존재하는 단일 구멍의 반경을 바꿔가며 응력 집중 계수의 변화를 분석하였다. 같은 방법으로 일렬로 존재하는 구멍들 사이에서의 응력 집중 계수를 수치 해석하였다. 각각의 응력 집중 계수를 이론값과 비교하여 정확도를 확인하였다. 마지막으로 두 응력 집중 현상을 독립적으로 적용하는 최적화 방법을 확인 및 검증하였다. 이 결과들은 이론적인 예측과 밀접한 경향성을 보여 앞으로의 리벳 배치 최적화에도 활용될 수 있을 것으로 예상된다.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.25-34
• /
• 2010

Fretting damage reduces fatigue life of the material due to low amplitude cyclic sliding and changes in the contact surfaces of strongly connected machine and structures such as bolt, key, fixed rivet and connected shaft, which have relative slip of repeatedly very low frequency amplitude. In this study, the fretting fatigue behavior of 7050-T7451 aluminum alloys used mainly in aircraft and automobile industry were evaluated. The plain fatigue test and fretting fatigue test under cyclic bending load carried out commercial bending fatigue tester and specially devised equipments to cause fretting damage. From these experimental work, the following results obtained: (1) The plain fatigue limit for stress ratio R=-l was about 151MPa. (2) In case of fretting fatigue, fatigue limit for stress ratio R=-l about 72MPa, the fatigue limit for R=0 about 81MPa, and the fatigue limit for R=0.3 about 93MPa. (3) The fatigue limit reduction rates by the fretting damage were about 52%(R=-1), 46%(R=0) and 38%(R=0.3) respectively. (4) The fatigue limit reduction rate decreased with stress ratio increase. In fretting bending test, as stress ratio increased, occurrence of initial oblique crack by fretting decreased or phased out, so that fracture surfaces were formed by plain fatigue crack occurrence, and such tendency was notable as stress amplitude increased. (5) Tire tracks and rubbed scars were observed in the fracture surface and contacted surface.

• 한국기계가공학회지
• /
• 제20권5호
• /
• pp.76-84
• /
• 2021

In this study, an optimal stiffness model of the C-frame, which was supporting the mold and tool load, was proposed to obtain quality self-piercing riveting (SPR) joining. First, the load path acting on the C-frame structure was identified using topology optimization. Then, a final suggested model was proposed based on the load path results. Stiffness and strength analyses were performed for a rivet pressing force of 7.3 [t] to compare the design performance of the final proposed model with that of the initial model. Moreover, to examine the reliability of continuous and repeated processes, vibration analysis was performed and the dynamic stiffness of the final proposed model was reviewed. Additionally, fatigue analysis was performed to ascertain the fatigue characteristics due to simple repetitive loading. Finally, stiffness test was performed for the final proposed model to verify the analysis results. The obtained results differed from the analysis result by 2.9%. Consequently, the performance of the final proposed model was superior to that of the initial model with respect to not only the SPR fastening quality but also the reliability of continuous and repetitive processes.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.155-156
• /
• 2023

In the case of steel door frames commonly found in general buildings, there are various assembly methods such as rivets, bolts, and welding, but the welding method is generally used. However, this welding joint method has many problems, such as distortion due to heat and damage due to external shock. In particular, when used as a fire door, problems may occur in the event of a fire due to distortion caused by heat from welding and the weak welded joint area. In the case of rivet or welded joints, when moved after assembly, joint loosening due to external shock may occur. Problems may arise where the bonding strength becomes weak. In addition, with the recent increase in high-rise buildings and larger buildings, when assembly is completed and brought to the site, a place is needed to store it, and in addition, there is a problem in that it has to be transported several times in small quantities to the installation site, which is another problem of time and cost loss. This is coming to the fore. In order to fundamentally solve this problem, we have researched and developed a non-welding door frame that can be assembled on site. We have researched and developed three assembly methods: screw-type, insert-type, and protrusion-type. Non-welded door frames are small in size and easy to package, making them advantageous for domestic and overseas exports.