• Membrane Journal
• /
• v.8 no.2
• /
• pp.102-108
• /
• 1998

Permeation behavior of the semiconductor rinsing wastewater containing Si particles was examined by ultrafiltration using the polysulfone plate membrane. The permeation flux was gradually decreased with time. It was due to the growth of cake deposited on the membrane surface and the pore plugging by Si particles. Permeation flux of cross flow type was 1.4 times higher than that of the dead end flow type. Nitrogen back flushing which is the removing method of membrane fouling was superior to the water sweeping. With nitrogen back flushing, the decrease of permeation flux due to the fouling was recovered about 85 % to the initial flux in the flat plate membrane system. The rejection rate of Si particles was about 90 % and the size of Si particle in the permeate was about 70 nm.

• Journal of Biosystems Engineering
• /
• v.41 no.2
• /
• pp.75-84
• /
• 2016

Purpose: In-situ water quality monitoring based on ion-selective electrodes (ISEs) is a promising technique because ISEs can be used directly in the medium to be tested, have a compact size, and are inexpensive. However, signal drift can be a major concern with on-line management systems because continuous immersion of the ISEs in water causes electrode degradation, affecting the stability, repeatability, and selectivity over time. In this study, a computer-based nitrate monitoring system including automatic electrode rinsing and calibration was developed to measure the nitrate concentration in water samples in real-time. Methods: The capabilities of two different types of poly(vinyl chloride) membrane-based ISEs, an electrode with a liquid filling and a carbon paste-based solid state electrode, were used in the monitoring system and evaluated on their sensitivities, selectivities, and durabilities. A feasibility test for the continuous detection of nitrate ions in water using the developed system was conducted using water samples obtained from various water sources. Results: Both prepared ISEs were capable of detecting low concentrations of nitrate in solution, i.e., 0.7 mg/L $NO_3-N$. Furthermore, the electrodes have the same order of selectivity for nitrate: $NO_3{^-}{\gg}HCO_3{^-}$ > $Cl^-$ > $H_2PO_4{^-}$ > $SO{_4}^{2-}$, and maintain their sensitivity by > 40 mV/decade over a period of 90 days. Conclusions: The use of an automated ISE-based nitrate measurement system that includes automatic electrode rinsing and two-point normalization proved to be feasible in measuring $NO_3-N$ in water samples obtained from different water sources. A one-to-one relationship between the levels of $NO_3-N$ measured with the ISEs and standard analytical instruments was obtained.

• The Korean Journal of Food And Nutrition
• /
• v.21 no.2
• /
• pp.176-183
• /
• 2008

This study examined the anti-microbiological effects of chlorine treatment on the surface of fresh fruits, in order to improve microbiological safety in school foodservice operations. Non-peeled fruit(strawberries) and peeled fruit(bananas) were treated with different concentrations of chlorinated water and rinsing numbers, followed by microbiological testing. The fruits were immersed at different concentrations of chlorinated water(0 ppm, 50 ppm, and 100 ppm) and durations(3 min and 5 min), and were then rinsed with tap water(one time, two times, or three times). The total viable cell counts of both the strawberries and bananas ranged from $10^3$ CFU/g to $10^4$ CFU/g, and coliform levels ranged from $10^2$ CFU/g to $10^3$ CFU/g. As the chlorine concentration, immersion time, and rinsing number increased, anti-microbiological activity increased. The largest microbial reduction was shown with immersion for 5 min in 100 ppm chlorinated water and three rinsings. In the strawberries, this treatment reduced the initial population of total viable cells and coliforms by 3.29 log CFU/g and to an undetectable level, respectively, no total viable cells or coliforms were detected on the banana surface following this treatment. However, after a sterilization treatment with immersion for 5 min in 50 ppm chlorinated water and three rinsings, the total viable cell counts and coliform counts of the strawberries and bananas decreased to acceptable levels, based on the microbiological standards for ready-to-eat foods. Overall, it was shown that the sterilization treatment of 50 ppm chlorinated water, soaking for 5 min, and three rinsings provided an effective reduction in surface microbes, and enhanced the microbiological safety of the fruit.

• Membrane Journal
• /
• v.9 no.1
• /
• pp.36-42
• /
• 1999

Permeation behavior of the semiconductor rinsing wastewater contammg Si particles was examined by ultrafiltration using the polyolefin tubular membrane. Flux decline with time was due to the growth of Si cake deposited on the membrane surface and the pore plugging by Si particles. Cake filtration from the cross flow application is compared to the combination of pore blocking and cake filtration from the dead-end application. The cake resistance is 3.16 x $10^{12}$ -4.34 X $\times$$10^{12}$ $m^{-1}$ for the cross flow and 6.6 x $\times$$10^{12}$ -12.19 X $\times$$10^{12}$ $\times$$m^{-1}$for the dead-end flow, respectively. At the initial stage of operation, permeation flux of cross flow type was 1.7 time higher than that of the dead end flow type. Permeation flux of cross flow was about 42 e 1m2 hr and the rejection rate of Si particles was about 96 %. The average particle size of Si particle in the permeate was 20 nm.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.557-564
• /
• 2015

The previous etching, rinsing and drying processes of wafers for MEMS (microelectromechanical system) using SC-$CO_2$ (supercritical-$CO_2$) consists of two steps. Firstly, MEMS-wafers are etched by organic solvent in a separate etching equipment from the high pressure dryer and then moved to the high pressure dryer to rinse and dry them using SC-$CO_2$. We found that the previous two step process could be applied to etch and dry wafers for MEMS but could not confirm the reproducibility through several experiments. We thought the cause of that was the stiction of structures occurring due to vaporization of the etching solvent during moving MEMS wafer to high pressure dryer after etching it outside. In order to improve the structure stiction problem, we designed a continuous process for etching, rinsing and drying MEMS-wafers using SC-$CO_2$ without moving them. And we also wanted to know relations of states of carbon dioxide (gas, liquid, supercritical fluid) to the structure stiction problem. In the case of using gas carbon dioxide (3 MPa, $25^{\circ}C$) as an etching solvent, we could obtain well-treated MEMS-wafers without stiction and confirm the reproducibility of experimental results. The quantity of rinsing solvent used could be also reduced compared with the previous technology. In the case of using liquid carbon dioxide (3 MPa, $5^{\circ}C$, we could not obtain well-treated MEMS-wafers without stiction due to the phase separation of between liquid carbon dioxide and etching co-solvent(acetone). In the case of using SC-$CO_2$ (7.5 Mpa, $40^{\circ}C$), we had as good results as those of the case using gas-$CO_2$. Besides the processing time was shortened compared with that of the case of using gas-$CO_2$.

• Journal of Oral Medicine and Pain
• /
• v.36 no.4
• /
• pp.245-252
• /
• 2011

The aim of this study is to clinically evaluate the effect of a mouthwash containing cetylpyridinium and zinc chloride on reduction of morning oral malodor in healthy subjects measured by organoleptic measurement and a portable sulfide monitor. A total of 8 healthy non-smoking male volunteers were enrolled in this study of crossover design consisting of two experimental phases. The subjects were instructed to rinse the mouth with 10 mL of the experimental mouthwash containing cetylpyridinium and zinc chloride for 30 seconds at the first phase. At the second phase after a one-week washout period, each subject rinsed with distilled water as a control. All experiments were conducted at around 8:30 a.m. and oral malodor was measured using organoleptic measurement and a portable sulfide monitor just before rinsing with the experimental mouthwash or control (baseline), 1 hr, 2 hrs, and 3 hrs after rinsing. The mouthwash containing cetylpyridinium and zinc chloride reduced morning oral malodor up to 3 hrs after rinsing. Organoleptic score and concentrations of volatile sulfur compounds after use of the experimental mouthwash significantly decreased with time, and the decreases were significantly different between the mouthwash and control. In conclusion, the mouthwash containing cetylpyridinium and zinc chloride is significantly effective on reduction of morning oral malodor in healthy subjects by 3 hrs.

• Composites Research
• /
• v.32 no.6
• /
• pp.314-318
• /
• 2019

A simple and very flexible automatic dipping machine was constructed for producing functional multilayer films on wide substrates via the layer-by-layer (LbL) assembly technique. The proposed machine exhibits several features that allow a fully automated coating operation, such as various depositing recipes, control of the dipping depth and time, operating speed, and rinsing flow, air-assist drying nozzles, and an operation display. The machine uniformly dips a substrate into aqueous mixtures containing complementary (e.g., oppositely charged, capable of hydrogen bonding, or capable of covalent bonding) species. Between the dipping of each species, the sample is spray cleaned with deionized water and blow-dried with air. The dipping, rinsing, and drying areas and times are adjustable by a computer program. Graphene-based thin films up to ten-bilayers were prepared and characterized. This film exhibits the highly filled multilayer structures and low thermal resistance, indicating that the robotic dipping system is simple to produce functional thin film coatings with a variety of different layers.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.31 no.8
• /
• pp.1231-1239
• /
• 2007

The purpose of this study was to investigate consumer's behaviors on the laundering of baby's clothing according to washing machine types. The subjects were 255 consumers with babies(0-2 years) in Korea. The data were collected with a self-administered questionnaire and analyzed by Chi-square test and multiple response analysis, and SPSS 12.0 statistics package was used. Consumers were separated into two groups according to washing machine types with general pulsator type and drum-type. Consumer's behaviors between general pulsator type group and drum-type group of washing machines were also examined. The results of this study were as follows. In the consumer satisfaction for washing machine, mostly drum-type group of consumers were satisfied with their washing machines. As the reasons of washing machine's dissatisfaction, noise, washing time and low washing efficiency were high in the pulsator type group, and washing time, noise and high price in the drum-type washing machine group. The consumers concerned about separation of clothing and laundering label while they washed laundry by washing machine. However, they didn't separate clothing because the small volume of laundry and a long washing time. The most interest and required thing of consumers was complete rinsing without any detergents used in washing as well as the removal of soils for baby's clothing regardless of two washing machine types. And they complained food soils like milk and mother's milk etc. were not completely removed by washing machine. As a whole the washing frequency of baby's laundry was once per a day and the rinsing also more than three times per a laundry. Most of the consumers used a private detergents for baby's clothing(detergents for baby's clothing only), and preferred to the high or boiled temperature washing as a desirable baby's laundering. There were significant differences between general pulsator type group and drum-type group of washing machines on the laundering of baby's clothing in this study.

• Journal of Korean Society on Water Environment
• /
• v.22 no.3
• /
• pp.437-443
• /
• 2006

The Water usage is relationship which is close with the administrative cost from industrial facility. It is not easy to reduce a water usage. This research is the optimization of the waste water quantity which process waste water integration of the standard thermal power plant in system operate time. The turbine rotates by force of the steam and it produces an electricity. Demineralization Water is manufacture purity manufacturing equipment and it is supplied in power plant channel. We knew a possibility of reducing from pure control process. When it is reduced the Back Washing time, Rinsing time of the gravity filter and the activated carbon filter. Also, It is possible even from regeneration phase in Condensate Polishing Demineralization System. In addition, There is also the water which the drain of the sampling water for watching the condition of power plant process will be able to use. Integrates these processes it will be able to reduce an annual 30,000 ton degree. The research is want to use the fundamental data for the water curtailment of the power plant.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.295-298
• /
• 2015

Ozone micro-bubble cleaning system was designed, and made to develop a unique technique to clean wafers by using ozone micro-bubbles. The ozone micro-bubble cleaning system consisted of loading, cleaning, rinsing, drying and un-loading zones, respectively. In case of the cleaning the silicon wafers of a solar cell, more than 99 % of cleaning efficiency was obtained by dipping the wafers at 10 ppm of ozone for 10 minutes. Both of long cleaning time and high ozone concentration in the wet-solution with ozone micro-bubbles reduced cleaning efficiency because of the re-sorption of debris. The cleaning technique by ozone micro-bubbles can be also applied to various wafers for an ingot and LED as an eco-friendly method.