• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.9
• /
• pp.1285-1291
• /
• 2013

In this paper, a double circular ring monopole antenna for wideband applications is designed and fabricated. The proposed antenna is based on a planar monopole design, and composed of double circular ring of radiating patches and ground plane to obtain the wideband characteristics. To get the optimized parameters, we used the simulator, Ansoft's High Frequency Structure Simulator(HFSS) and found the parameters that effect antenna characteristics. Using the obtained parameters, the proposed antenna is fabricated. The fabricated antenna is measured at the operating frequencies, and the return loss coefficient, gain, and radiation patterns are determined. The results of measurement, -10dB impedance bandwidth, measured return loss is 4,530 MHz(2,510-7,040 MHz) and antenna peak and average gains for the frequencies are obtained 0.71~3.38 dBi, -3.85~0.3 dBi, respectively. In case of radiation patterns, the proposed antenna displays nearly omnidirectional radiation characteristics in the E-plane, and monopole-like radiation pattern characteristics in the H-plane.

• Journal of Navigation and Port Research
• /
• v.26 no.5
• /
• pp.529-535
• /
• 2002

Design and implementation methodologies on the performance evaluation system of Two-Channel Ring-Core Flux-Gate Compass (TCRC FG-Compass) are described, with evaluation procedures and methods based on the polynomial regression models. Performance evaluation system consists of a step motor driving unit, a bearing transmitting unit and evaluation programs derived from polynomial regression formulae. Newly designed performance evaluation system enabled the accuracy of TCRC FG-Compass to be ascertained. It was confirmed that the size of residual deviation of TCRC FG-Compass is $2^{\circ}$, while that of the conventional one is $4^{\circ}$. In addition, the design methodology to the self estimation and correction of residual deviations is also discussed.

• Journal for History of Mathematics
• /
• v.32 no.4
• /
• pp.159-173
• /
• 2019

In this paper, we examine the brief history of the ring of four almonds regarding Mesopotamian mathematics, and present reasons why the Omar Khayyam's triangle, a special right triangle in a ring of four almonds, was essential for artisans due to its unique pattern. We presume that the ring of four almonds originated from a point symmetry figure given two concentric squares used in the proto-Sumerian Jemdet Nasr period (approximately 3000 B.C.) and a square halfway between two given concentric squares used during the time of the Old Akkadian period (2340-2200 B.C.) and the Old Babylonian age (2000-1600 B.C.). Artisans tried to create a new intricate pattern as almonds and 6-pointed stars by subdividing right triangles in the pattern of the popular altered Old Akkadian square band at the time. Therefore, artisans needed the Omar Khayyam's triangle, whose hypotenuse equals the sum of the short side and the perpendicular to the hypotenuse. We presume that artisans asked mathematicians how to construct the Omar Khayyam's triangle at a meeting between artisans and mathematicians in Isfahan. The construction of Omar Khayyam's triangle requires solving an irreducible cubic polynomial. Omar Khayyam was the first to classify equations of integer polynomials of degree up to three and then proceeded to solve all types of cubic equations by means of intersections of conic sections. Omar Khayyam's triangle gave practical meaning to the type of cubic equation $x^3+bx=cx^2+a$. The work of Omar Khayyam was completed by Descartes in the 17th century.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1275-1277
• /
• 1995

We designed and constructed an extremly high power s-band traveling wave resonator for the test of high power microwave components using 80MW pulsed klystron with $4{\mu}s$ pulse width. The 10dB directional coupler for the input power coupling was used, and the ring consists of phase shifter, tuner, H-band, and other microwave components. The designed total electrical length of the system is 10 times of the waveguide wavelength, ${\lambda}_g$=15.3cm, and the measured total insertion loss is 0.15dB. The low power test measurment showed the power multiplication of 14.69. The design goal is to achieve the peak power of 300MW, pulse width $4{\mu}s$ with 30 pulse repetition rate. In this article we discuss the treveling wave resonant ring constructed at the PAL laboratory together with the test results.

• Journal of the Korea Furniture Society
• /
• v.16 no.1
• /
• pp.17-23
• /
• 2005

European maple is famous for the optimum solid wood for making bridge which is the most important part in violin acoustics. This study was carried out to investigate the variation of main features, i. e. annual ring width and cutting direction of costly imported violin bridge blanks and to examine the effect of these features of the blanks on the vibrational characteristics of bridge blanks. Imported violin bridge blanks had somewhat large variation in major macroscopical and physical properties and there was little relationship between annual ring density and weight of maple blanks. Resonant frequency of violin bridge blanks had some positive correlation with weight, however, damping having negative relationship with frequency was seldom affected by any physical properties of the maple blanks. Deviation from the radial cutting of tail side(ray direction from top toward feet on the edge of bridge blank) lowered the resonant frequency. Consequently, weight and ray direction should be taken for the critical quality decisive factors(QDF) of incoming bridge blanks by not only inspectors also luthiers who tune the bridge by shaping and are responsible for the final timbre quality of this complicate instrument.

• Journal of the Korean Society of Industry Convergence
• /
• v.15 no.1
• /
• pp.13-19
• /
• 2012

Due to a low stiffness of cranktrain and a failure experience from a history within short development time, a viscous torsional vibration damper was applied in order to reduce the torsional vibration and keep the high reliability for the durability of cranktrain system in the direct injection diesel engine. As an improvement of the crankshaft stiffness by increasing the diameter of main and pin journal, a rubber type damper could be considered. In this study, the control factors of rubber damper, the moment of inertia ring, stiffness of damper and damping coefficient of ring, were investigated by DFSS method through the analysis work and the measurement in the real engine condition.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.215-216
• /
• 2008

In this paper, we describe a UHF-band CMOS fractional-N frequency synthesizer using a ring - type VCO. It has been designed using $0.18{\m}m$ CMOS technology. First, The newly designed charge-pump circuit includes an OTA for matching between the upper current and the lower current In addition, a ring - type VCO is also used for small chip sire. The simulation results show that the designed circuit has a phase noise of -109.53dBc/Hz at 1MHz offset and consumes 19.4mA from a 1.8V supply. The lock time is less than 30usec and the chip size is $0.45mm{\times}0.5mm$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.8A
• /
• pp.688-696
• /
• 2005

An antenna was designed and manufactured for the DBS receiver system. This antenna is a planar or flat antenna which shows many advantages over the conventional parabolic antenna such as higher aperture efficiency, easier installation and improved aesthetics to name a few. The antenna is a novel design employing microstrip annular ring resonating antenna elements and a radial waveguide feeder network. The LNB(Low Noise Blockdown Converter) is can integrate with the antenna iしt the back of the radial waveguide. The 35cm diameter antenna works at 31.8dBi minimum gain which implies an aperture efficiency of around $80\%$.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.4
• /
• pp.357-364
• /
• 2011

In this study, ring-shaped acoustic resonators were proposed to be installed in a silencer to increase the acoustic performance of silencer in the low-frequency range. Evaluation of noise reduction performance of acoustic resonator arrays was carried out by measuring the random-incidence absorption coefficient. It was found that the absorption coefficient of resonator array was measured up to 1 at 125 Hz of 1/3-octave band center frequency. Insertion losses of silencers with ring-shaped acoustic resonator arrays were measured based on ISO 7235. The results were shown that the ring-shaped resonator could increase the insertion loss up to 13 dB without flow, whereas 7 dB when flow speed reached 15 m/s. As increasing the flow speed above 15 m/s, the effect of acoustic resonator decreased due to the effect of nonlinear air damping of the resonator. It was also found that the increment of pressure drop by the presence of resonator arrays was about 9 % at flow speed of 25 m/s.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.11
• /
• pp.960-967
• /
• 2013

Shape recognition of solder ball bumps in a BGA (Ball Grid Array) is an important issue in flip chip bonding technology. In particular, the semiconductor industry has required faster and more accurate inspection of micron-size solder bumps in flip chip bonding as the density of balls has increased dramatically. The difficulty of this issue comes from specular reflection on the metal ball. Shape recognition of a metal ball is a very realproblem for computer vision systems. Specular reflection of the metal ball appears, disappears, or changes its image abruptly due to tiny movementson behalf of the viewer. This paper presents a practical shape recognition method for three dimensional (3-D) inspection of a BGA using a 5-step ring illumination device. When the ring light illuminates the balls, distinctive specularity images of the balls, which are referred to as "iso-slope contours" in this paper, are shown. By using a mathematical reflectance model, we can drive the 3-D shape information of the ball in aquantitative manner. The experimental results show the usefulness of the method for industrial application in terms of time and accuracy.