• 한국농공학회논문집
• /
• 제51권3호
• /
• pp.71-78
• /
• 2009

Pipe section of bending part at the arch type pipe-house showed an ellipse with oblateness of 0.076 on the average. Flexural rigidity of bending part decreased by average 6.3% than that of an original round shape section. The deflection of arch type pipe-house measured by model experiments showed much bigger than the result of structural analysis. In case of arch type pipe-house, we supposed that the decrease of flexural rigidity for the bending part of pipes had an effect on deflection of roof under the working load. This effect should be considered in the structural analysis. Bending resistance of gable type pipe-house used a prefabricated connector which developed in this study showed about $1.5{\sim}1.8$ times stronger than that of the existing arch type or gable type processed bending. Therefore, we supposed that the gable-roofed prefabricated pipe-house is safer than arch type or bent gable type in case of heavy snowfall. According to house scales and section properties of steel pipe in use, safe snow depths and rafter intervals were presented for design of gable-roofed prefabricated pipe-house. Their standards were established in the range of the durable models recommended by RDA, and the comparative examinations were conducted by means of structural analysis. It was evaluated that the developed greenhouse model had a high applicability in the field.

• 한국지반신소재학회논문집
• /
• 제5권3호
• /
• pp.9-15
• /
• 2006

그린월 공법은 독립식 콘크리트 보형식의 옹벽으로, 전, 후면 가로보와 세로 방향으로 버팀보를 연속적으로 쌓아 올려 내부에 다짐성토를 시행함으로써 구조체가 일체 거동하도록 강성벽체(rigid body)를 형성시키는 옹벽 구조물이다. 최근의 그린월공사는 원지반 절취량을 최소화 할 수 있다는 장점으로 절토 공사현장에 다양하게 적용되고 있으며, 주로 앵커 및 쏘일네일 등과 함께 시공하는 추세이다. 이처럼 그린월과 함께 쏘일네일이 시공되는 경우에는 전면벽체의 강성이 크기 때문에 연성전면벽체의 경우 보다 전체 시스템의 안정성 증대가 예상되나 실제 설계에서는 이를 반영하지 않고 쏘일네일만 설계하므로 비경제적인 요소가 많은 실정이다. 따라서 본 연구에서는 그린월과 같은 강성전면벽체와 쏘일네일 공법이 함께 시공되는 경우에 대하여 강성전면벽체로 인한 전체 시스템의 안정성 증대효과를 평가해 보았다. 본 연구에서는 전면벽체의 강성변화에 따른 전체 시스템의 안정성 증대효과를 평가하기 위하여 실내모형실험을 수행하였으며, 한계평형해석을 시행하여 그린월과 같은 전면벽체의 강성이 전체 활동에 대한 안전율에 미치는 영향을 평가하였다.

• 디지털융복합연구
• /
• 제14권11호
• /
• pp.45-51
• /
• 2016

개인정보 유출 사고를 불러일으키는 근거를 과학적으로 발굴해 보려는 연구는 아직까지 전무한 실정이다. 본 논문은 해킹을 통한 주민 정보 유출의 정도를 결정짓는 근거 요인을 찾아내기 위해 시도됐다. 연구의 중요도에 비추어 이를 위한 연구가 문헌상에 나타나지 않았던 점은 과학적인 연구방법론을 찾아내고 적용하기 곤란한 연구주제인 점에서 본 논문에서는 과학적 분석 모형을 제안하였고 그에 기반 한 분석 방법론을 개발하였다. 연구결과, 개인 식별에 동원되는 데이터의 경직성 요인이 유출 수위에 가장 결정적 역할을 하는 것으로 드러났다. 강도가 강할수록 해킹건수와 비례하는 것이 증명됐다. '주민 데이터 자유도' 개념을 정립함으로써 국가별 주민식별관련 주민 자유도 허용 순위를 결정할 수 있었다. 영국과 한국이 순위 열 양단에 위치하는 것으로 드러났으며 자유도 면에서 영국이 국민에게 가장 많은 자유를 허용하는 국가로, 또한 한국이 가장 좁은 의미의 자유를 허용하는 국가로 매겨졌다.

• 한국농공학회지
• /
• 제34권1호
• /
• pp.49-56
• /
• 1992

This study was carried out to investigate the mechanical behaviour of the plate on a Winkler's foundation according to the soil-structures relative stiffness and the applicability of the conventional analysis method. For the above purpose, Winkler's constant of 4, 15, 25 and 100kg/$cm^2$/cm was considered and the plate thickness of 20, 30, 50, 100 and 150cm was adopted. Results obtained from the numerical examples are summarized as follow: 1. The effects of elastic foundation is considerable for plates with small flexural rigidity. 2. As the Winkler's constant increases, the bending moment in the plate becomes localized near the loading point. 3. The stresses evaluated by the conventional method not correct even for rigid ground such as rock. 4. If the relative stiffness of the plate is very large, for example the plate thickness is larger than 100cm, the conventional analysis method can be justified for the design purposes. 5. On assumption the flexural rigidity of the plate is infinite, the interaction of soil and plate can be ignored in design consideration. The numerical examples in this paper show that when the plate thickness is more than 100cm, the effects of elastic foundation almost disappear. In practical design, soil-plate interaction should be taken into account, because the 100cm-thickness of the plate will not be practical value in usual sites.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.78-83
• /
• 2016

The development of an exclusive 8-axis multi-tasking machine to finish multiple cutting processes by a single piece of power equipment for securing the high-precision machining and high productivity of the series of shafts (a core part of the automotive powertrain that delivers engine power) is needed. The rigidity of the structure must be improved and the weight of the structure must be reduced to develop a multi-tasking machine with high precision and high productivity. In this paper, we perform a static structural analysis of the initial design of the multi-tasking machines and compare the results of the multi-tasking machines improved by the reinforced design and the results of the initial one. According to the results of the structural analysis, the rigidity of the reinforced machine was increased and the overall weight was decreased. Therefore, the productivity was increased.

• Journal of Astronomy and Space Sciences
• /
• 제35권4호
• /
• pp.219-225
• /
• 2018

Cosmic rays are ions that move at relativistic speeds. They generate secondary cosmic rays by successive collisions with atmospheric particles, and then, the secondary particles reach the ground. The secondary particles are mainly neutrons and muons, and the neutrons are observed by the ground neutron monitor. This study compared the diurnal variation in cosmic ray intensity obtained via harmonic analysis and that obtained through the pile-up method, which was examined in a previous study. In addition, we analyzed the maximum phase of the diurnal variation using four neutron monitors with a cutoff rigidity below approximately 6 GV, located at similar longitudes to the Oulu and Rome neutron monitors. Expanding the data of solar cycles 20-24, we examined the time of the maximum cosmic ray intensity, that is, the maximum phase regarding the solar cyclic modulation. During solar cycles 20-24, the maximum phase derived by harmonic analysis showed no significant difference with that derived by the pile-up method. Thus, the pile-up method, a relatively straightforward process to analyze diurnal variation, could replace the complex harmonic analysis. In addition, the maximum phase at six neutron monitors shows the 22-year cyclic variation very clearly. The maximum phase tends to appear earlier and increase the width of the variation in solar cycles as the cutoff rigidity increases.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2009년도 정기 학술대회
• /
• pp.425-428
• /
• 2009

This paper presents a sensitivity-based finite element (FE)-model update procedure for prestressed concrete (PSC) girder bridge model using vibration test results. Firstly, the stiffness parameters of the structure such as flexural rigidity of concrete and flexural rigidity of tendon are chosen as updating parameters. Next, the numerical frequencies of first two bending modes are calculated using a three-dimensional FE model which is established for the PSC girder. Then, the corresponding experimental frequencies which are obtained from forced vibration tests are selected. In order to perform the model update, the eigensensitivity-based method is employed. Finally, the effect of prestress-loss on the stiffness parameters is evaluated.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.455-460
• /
• 2001

Generally, the contribution of curbs and median strip is not considered carefully in analysing and designing the girder bridges. There being curbs, the load given on interior girder relatively reduced and on exterior girder increased. Curbs and median strip reduce the load distribution factor by distributing the load given on girder fairly, In this paper, the Influence of curbs and median strip in wheel distribution through parameter study and lateral distribution test of PSC girder bridge was investigated. Finite-element analysis was performed with parameterizing the flexural rigidity of the girder, span length, girder spacing, median strip, curbs. The influence of curbs and median strip would increase with lowering rigidity of girder. In addition, curbs lower the load distribution factor of exterior and interior girders.

• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.39-48
• /
• 2006

In this paper, polymer composites based sandwich structures like beams and plates are optimised by using parametric study. The structures are composed of fibre reinforced composites for facial material and resin concrete and PVC foam for core materials. The stacking sequences and thickness of the composites are controlled as major parameters to find out the optimal condition for machine tool components. For the plate structure of machine tool bed composites-skined sandwich structure which has several ribs are proposed to enhance bending stiffnesses in two major directions at the same time. Dynamic robustness of a machine tool structure is investigated using modal analysis. From the results optimal configuration and materials for high precesion machine tools are proposed. And the plate was made of fiber reforced composite material and PVC foam.

• 복식
• /
• 제26권
• /
• pp.211-220
• /
• 1995

The purpose of this study was to examine the relationships between the interest of apparel ad-vertising direct mail(DM) and the consumers' characteristics ; like their marital state, age, educational level, expenses on clothing purchase, and rigidity. Samples were 243 women(24∼35 years of age) in the Seoul, Korea. The data were analyzed using t-test, one-way ANOVA, Duncan's multiple range test, and discriminant analysis. The results of the study were the followings. 1. The department store sent out the most ap-parel advertising DM and the most common dis-tribution method was carrying the DM with the newspapers, 2/3 consumers paid attention to the contents of the apparel advertising DM with 'some interests'. 2. Jackets and pants were the most purchased items after seeing the apparel advertising DM. 3. The interest in the contents of the apparel advertising DM varied according to the consumers' marital state ad the expenses on cloth-ing purchase. 4. Rigidity, age, educational level, and the clothing purchase expenses contributed to discriminant the interesting or uninteresting group in DM. The accuracy rate of the predicting the groups by the 4 variables was 60.91%.