• 한국지진공학회논문집
• /
• 제9권2호통권42호
• /
• pp.59-69
• /
• 2005

용접 철골 모멘트접합부는 일반적으로 평면유지의 가정을 전제한 초등휨이론에 의해 설계되어 왔다. 그러나 1994년 노스리지 지진 이후 보-기둥 접합부의 설계에 초등휨이론을 적용하는 것은 타당치 않음이 몇몇 연구자에 의해 제기된 바가 있다. 본 연구에서는 필자의 최근 해석 및 실험연구를 주 근거로 하여 다양한 형식의 접합부의 응력전달 메커니즘을 재평가하고, 거의 모든 용접 모멘트접합부의 설계에 초등휨이론을 적용하는 것이 부적절함을 보이고자 하였다. 보의 웨브, 수평헌치의 웨브, 리브 등과 같은 수직 플레이트 접합요소는 모두 스트럿 작용에 의해 응력을 전달하는 유사성이 있음을 해석적, 실험적으로 확인하였다. 또한 최근 가장 큰 주목을 받고 있는 고연성 RBS 접합부의 전단력 응력전달 메커니즘은 PN형식 접합부의 그것과 크게 다르지 않음을 확인하였다. 아울러 접합부 설계에 유용하게 활용될 수 있는 단순화된 해석적 응력전달 모형을 소개하였다.

• 한국수자원학회논문집
• /
• 제52권4호
• /
• pp.255-264
• /
• 2019

산지하천 만곡부의 홍수피해를 줄이고자 사다리꼴 단면의 돌출줄눈을 하천옹벽에 설치하였다. 본 연구에서는 사다리꼴 형상에 의한 흐름저항 효과를 파악하고자 개수로 측벽에 사다리꼴 돌출줄눈을 설치하여 수리실험을 수행하였다. 벽면조도가 k형에 해당하는 ${\lambda}_{nv}$가 6, 9, 12인 경우에 대해 유량에 따른 흐름특성을 파악하였다. 흐름저항은 돌줄줄눈의 설치간격이 멀어짐에 따라 전반적으로 증가하였다. 고유량 조건에서 최대마찰계수는 ${\lambda}_{nv}$가 9일 때 발생하였다. 사다리꼴 돌출줄눈은 정사각형 돌출줄눈과 비교해 흐름저항은 상대적으로 작았지만, 사다리꼴의 형상저항은 전체 흐름저항의 평균 62%를 차지했다. 벽면조도 증가에 따른 흐름저항 효과를 극대화하기 위한 사다리꼴 돌출줄눈의 최적 설치간격은 돌출줄눈 높이의 9~12배 범위임을 확인하였다.

• 한국태양에너지학회 논문집
• /
• 제39권1호
• /
• pp.77-89
• /
• 2019

The solar air heater has various performances according to an obstacle installed in the air duct. Many studies on thermal performance have been conducted. But many of these studies were using a kind of rib type obstacle attached at the bottom of absorbing plate, but they are so hard to be manufactured. In this study, characteristics of the heat transfer and pressure drop in the solar air heater with various horizontal rectangular obstacles was investigated by CFD (Computational Fluid Dynamics) analysis. As a result, the heat transfer performance was improved from 1.2 to 3.32 times depending on installation conditions of rectangular obstacle. The pressure drop, however, also increased with increment of heat transfer performance from 2.8 to 180 times only by changing installation conditions of rectangular obstacle. Thus, the performance factor presenting the thermal performance enhancement on the same pressure drop was also confirmed. As a result, the highest value of 0.828 as better performance factor was obtained at the lower height of rectangular obstacle and this value has started to decrease with increment of heat transfer performance. In the end, it could be confirmed that the pressure drop was carried higher than the quantity of improvement of the heat transfer performance when the heat transfer performance was increased by change of installation conditions of rectangular obstacle. Both heat transfer enhancement and pressure drop to be required for system need to be considered before the rectangular obstacles are applied to the solar air heater.

• 한국식생활문화학회지
• /
• 제37권3호
• /
• pp.213-238
• /
• 2022

This study aims to investigate protein consumption market trends in Korea. Protein consumption was divided according to the protein source into meat, fishery, and plant-based protein. To accomplish the goal of this study, food purchase data from 525 households panels collected by the Rural Development Administration over the last 10 years were used. The results of the study showed an increase or decrease in protein consumption by protein type over the last 10 years, and a reason to explain this change has been suggested. Specifically, this study found a dramatic increase in the consumption of several proteins, including beef sirloin, beef tenderloin, seasoned beef & steak, pork belly, pork shoulder, pork neck, seasoned pork, pork cutlet, sweet and sour pork, canned ham, chicken drumstick, chicken breast, dak gangjeong, Chinese fried chili chicken, salmon, eel, abalone, squid, octopus, webfoot octopus, octopus minor, canned whelk, tofu, cold bean soup,and plant-based milk. Some items showed no increase in consumption (such as beef jerky, pork rib, sausage, bacon, whole raw chicken, cutlass fish, oyster, fish cake, crab stick, surimi sausage,and canned fishery), whereas a few items showed decreased consumption (e.g., mackerel, pollack, cod,and canned tuna)

• Nuclear Engineering and Technology
• /
• 제53권6호
• /
• pp.1970-1978
• /
• 2021

The aim of this study was to optimize the target, moderator, and collimator (TMC) in a neutron beam generator for the accelerator-based BNCT (A-BNCT) system. The optimization employed the Monte Carlo Neutron and Photon (MCNP) simulation. The optimal geometry for the target was decided as the one with the highest neutron flux among nominates, which were called as angled, rib, and tube in this study. The moderator was optimized in terms of consisting material to produce appropriate neutron energy distribution for the treatment. The optimization of the collimator, which wrapped around the target, was carried out by deciding the material to effectively prevent the leakage radiations. As results, characteristic of the neutron beam from the optimized TMC was compared to the recommendation by the International Atomic Energy Agent (IAEA). The tube type target showed the highest neutron flux among nominates. The optimal material for the moderator and collimator were combination of Fluental (Al₂0₃+AlF₃) with ⁶⁰Ni filter and lead, respectively. The optimized TMC satisfied the IAEA recommendations such as the minimum production rate of epithermal neutrons from thermal neutrons: that was 2.5 times higher. The results can be used as source terms for shielding designs of treatment rooms.

• Structural Engineering and Mechanics
• /
• 제81권6호
• /
• pp.715-728
• /
• 2022

A new type of buckling-restrained braces (BRBs) with a longitudinally profiled steel plate working as the core (LPBRB) is proposed and experimentally investigated. Different from conventional BRBs with a constant thickness core, both stiffness and strength of the longitudinally profiled steel core along its longitudinal direction can change through itself variable thickness, thus the construction of LPBRB saves material and reduces the processing cost. Four full-scale component tests were conducted under quasi-static cyclic loading to evaluate the seismic performance of LPBRB. Three stiffening methods were used to improve the fatigue performance of LPBRBs, which were bolt-assembled T-shaped stiffening ribs, partly-welded stiffening ribs and stiffening segment without rib. The experimental results showed LPBRB specimens displayed stable hysteretic behavior and satisfactory seismic property. There was no instability or rupture until the axial ductility ratio achieved 11.0. Failure modes included the out-of-plane buckling of the stiffening part outside the restraining member and core plate fatigue fracture around the longitudinally profiled segment. The effect of the stiffening methods on the fatigue performance is discussed. The critical buckling load of longitudinally profiled segment is derived using Euler theory. The local bulging behavior of the outer steel tube is analyzed with an equivalent beam model. The design recommendations for LPBRB are presented finally.

• The Journal of Advanced Prosthodontics
• /
• 제1권1호
• /
• pp.19-25
• /
• 2009

STATEMENT OF PROBLEM. Primary stability at the time of implant placement is related to the level of primary bone contact. The level of bone contact with implant is affected by thread design, surgical procedure and bone quality, etc. PURPOSE. The aim of this study was to compare the initial stability of the various taper implants according to the thread designs, half of which were engaged to inferior cortical wall of type IV bone(Group 1) and the rest of which were not engaged to inferior cortical wall(Group 2) by measuring the implant stability quotient(ISQ) and the removal torque value(RTV). MATERIAL AND METHODS. In this study, 6 different implant fixtures with 10 mm length were installed. In order to simulate the sinus inferior wall of type IV bone, one side cortical bone of swine rib was removed. 6 different implants were installed in the same bone block following manufacturer s recommended procedures. Total 10 bone blocks were made for each group. The height of Group 1 bone block was 10 mm for engagement and that of group 2 was 13 mm. The initial stability was measured with ISQ value using Osstell $mentor^{(R)}$ and with removal torque using MGT50 torque gauge. RESULTS. In this study, we found the following results. 1. In Group 1 with fixtures engaged to the inferior cortical wall, there was no significant difference in RTV and ISQ value among the 6 types of implants. 2. In Group 2 with fixtures not engaged to the inferior cortical wall, there was significant difference in RTV and ISQ value among the 6 types of implants(P < .05). 3. There was significant difference in RTV and ISQ value according to whether fixtures were engaged to the inferior cortical wall or not(P < .05). 4. Under-drilling made RTV and ISQ value increase significantly in the NT implants which had lower RTV and ISQ value in Group 2(P < .05). CONCLUSIONS. Without being engaged to the inferior cortical wall fixtures had initial stability affected by implant types. Also in poor quality bone, under-drilling improved initial stability.

• 한국초지조사료학회지
• /
• 제32권3호
• /
• pp.293-300
• /
• 2012

본 시험은 수수${\times}$수단그라스 교잡종 품종의 생육특성, 사초수량 및 품질을 비교하기 위하여 2009년 경북 성주와 충남 천안에서 수행하였다. 시험구 배치는 8처리 3반복의 난괴법 배치로 하였다. 시험구의 처리는 품종으로 하였으며, 공시한 품종은 'Sordan79', 'SX17', 'Honey chew', 'Honey grazer', 'G7', 'Jumbo', 'Green star' 및 'GT56'를 공시하였다. 2지역 모두에서 출수형 4품종은 출수를 하였다. 그 외 생육특성에서는 품종 간에 차이가 없었으나 출수형과 BMR 품종이 다른 품종보다 당도가 높았다. 건물률 및 초장은 출수형이 비출수형 보다 높았다. 생초수량, 건물수량 및 TDN 수량도 출수형이 비출수형 보다 높았고 BMR 품종은 다른 품종보다 적었다. 조단백질과 조회분 함량은 출수형 품종이 비출수형 품종보다 많았으나 비섬유성탄수화물(NFC)은 상반된 결과를 보였다. BMR 품종의 ADF 및 NFC 함량은 다른 폼종 보다 작았다. 이상의 결과를 종합해 볼 때 출수형이 비출수형에 비하여 사초 생산성이 우수하고, 품질은 비출수형과 BMR 품종이 우수한 경향을 보였다. 그리고 BMR 품종은 당도가 높고 ADF 함량이 낮아 사초 품질 이 우수한 것으로 판단되었다.

• 사상체질의학회지
• /
• 제25권3호
• /
• pp.145-157
• /
• 2013

Objectives This study was aimed to reveal the characteristics of the body shape, face, voice and temperament in Taeyangin. Methods The subjects were recruited from November 2005 to August 2012. Sasang constitutional specialist in each clinics confirmed the Sasang Constitution. Taeyangin (TY) became a standard guidance to be compared with each other Sasang type. Anova test was used in analyzing continuous variables and factor analysis was conducted in temperament questionnaire in advance. Generalized propensity score with age and body mass index (BMI) was used in adjusted model. Significant level was .05 Results 1. The TY body shape were generally smaller than Taeeumin (TE) (p<0.001) and Soyangin (SY) (p<0.05) in crude. The TY body shape were still smaller than TE (p<0.05) and there was no significant difference between TY and SY except rib circumference in males and forehead circumference (p<0.05) in females in adjusted model. 2. The size of face and nose in TY was smaller than in TE and there was different between males and females' TY and others in the characteristics of eye, nose and forehead variables in crude (p<0.05). Most of differences between TY and TE were disappeared in adjusted model. 3. The vocal height and speed of TY was different other types and there was different between males and females' TY in some of frequency change rate in crude (p<0.05). Most of differences between TY and other types were similar before and after adjusted model. 4. The temperament of TY was different with SE before and after adjusted mode 1 (p<0.05). TY males showed difference in expression factor and TY females showed difference in behavior factor compared with TE respectively (p<0.05). Conclusions This study reveals characteristics of body shape, face, voice and character in the TY males females compared with each other type respectively.

• Tuberculosis and Respiratory Diseases
• /
• 제44권1호
• /
• pp.59-68
• /
• 1997

배 경 : 결핵성 흉벽 농양은 결핵의 드문 합병증이다. 결핵성 흉벽 농양은 다양한 병인에 따라 CT 소견에 차이가 있을 것으로 생각되며 이러한 차이를 밝히는 것이 결핵성 흉벽농양의 진단 뿐만 병인을 이해하는 것에도 도움이 될 것으로 생각된다. 대상 및 방법 : 결핵성 농양으로 확진된 20명의 환자를 대상으로 하였다. 20명 환자의 29개 농양을 활동성 폐실질 혹은 흉막 병변의 유무와 이들 병변과 농양의 접촉 여부에 따라 3가지 유형으로 분류하였다. l형은 폐실질 또는 흉막에 활동성 결핵성 병변이 없는 경우로, 2형은 활동성 폐결핵이나 흉막병변이 흉벽농양과 접하고 있는 경우로, 3형은 폐결핵이나 흉막병변이 있으나 농양과 접하고 있지 않는 경우로 각각 정의하였다. CT 유형에 따른 농양의 크기, 모양 및 위치 등의 차이를 분석하였다. 결 과 : l형에는 6명 환자의 6개의 농양이 속하였다. 이틀 농양은 늑골이나 늑연골의 파괴를 동반하며, 이것을 중심으로 크기가 크고 비교적 구형에 가까운 모양이었다. 2형은 10명 환자의 13개의 농양이 속하였다. 흉막 병변과 접하고 있는 7예와 종격동 림프절염과 접하고 있는 1예는 농양의 중심이 외근육층에 있고, 상하 길이가 긴 타원형의 모양이었다. 폐실질 병변과 접하고 있던 5예는 농양의 중심이 흉막외공간에 있고 크기가 작고 횡축이 긴 타원형이었다. 3형에는 6명 환자에서 10개의 농양이 속하였다. 이것들은 주로 흉막외공간에 생기며 크기가 작고 늑골의 장축을 따라 횡측의 길이가 긴 타원의 모양이고, 다발성의 빈도가 높았다. 결 론 : 결핵성 흉벽 농양은 농양의 모양과 동반된 폐실질 및 흉막 병변에 따라 몇개의 유형으로 나눌 수 있었다. 이러한, 유형의 차이는 다양한 병인에 따른 것으로 추정되며, 결핵성 흉벽 농양의 다양한 형태를 이해하는 것 이 진단 뿐만 아니라 병인을 이해하는데 도움이 될 것으로 생각된다. CT는 결핵성 농양의 진단 뿐만 아니라 농양의 범위, 동반된 폐실질및 흉막병변을 보는데 유용하다.